X-Over (Crossover); Setting The Crossover - Yamaha SP2060 Owner's Manual

Panel Operation

X-OVER (Crossover)

Setting the Crossover

Input signals can be divided into specified frequency ranges
to suit speaker response characteristics prior to output.
The number of division is determined to 1-way through 6-
way, depending on the selected component.
Parameter Range
∞
– , –138.00 through
LEVEL
+10.00dB
NORMAL
POLARITY
INVERTED
HPF
Refer to Step 4.
LPF
1.
Press the [X-OVER] key repeatedly until the X-
Over display appears on the screen.
OUT 1
FREQ = 20.0kHz
2.
Press the [SEL] key for the target Output
channel.
The [SEL] key LED of the selected channel lights up,
and the corresponding channel name is displayed.
OUT 3
FREQ = 20.0kHz
3.
Press the [NEXT]/[BACK] keys to select a
parameter to edit.
OUT 3
TYPE =24AdjustGc
Function
Adjusts the level of the
signal input to the
Crossover. The same
Level setting is used
for the output channels
of a component.
The output signal
phase for each
frequency range is
inverted.
LPF
LPF
LPF
4.
Press the [▲INC]/[▼DEC] keys to set the
parameter value.
Parameter Range
Thru
6dB/Oct
12dB/Oct AdjustGc
12dB/Oct Butrwrth
12dB/Oct Bessel
12dB/Oct Linkwitz
18dB/Oct AdjustGc
18dB/Oct Butrwrth
18dB/Oct Bessel
24dB/Oct AdjustGc
TYPE
24dB/Oct Butrwrth
24dB/Oct Bessel
24dB/Oct Linkwitz
36dB/Oct AdjustGc
36dB/Oct Butrwrth
36dB/Oct Bessel
48dB/Oct AdjustGc
HPF
48dB/Oct Butrwrth
48dB/Oct Bessel
48dB/Oct Linkwitz
FREQ
20.0Hz–20.0kHz
(Frequency)
Gc –6dB through +6dB
Thru
6dB/Oct
12dB/Oct AdjustGc
12dB/Oct Butrwrth
12dB/Oct Bessel
12dB/Oct Linkwitz
18dB/Oct AdjustGc
18dB/Oct Butrwrth
18dB/Oct Bessel
24dB/Oct AdjustGc
TYPE
24dB/Oct Butrwrth
24dB/Oct Bessel
24dB/Oct Linkwitz
36dB/Oct AdjustGc
36dB/Oct Butrwrth
36dB/Oct Bessel
48dB/Oct AdjustGc
LPF
48dB/Oct Butrwrth
48dB/Oct Bessel
48dB/Oct Linkwitz
FREQ
20.0Hz–20.0kHz
(Frequency)
Gc –6dB through +6dB
Function
Selects an
attenuation
amount per
octave, and a
type of filter.
If you select
"Thru," no filter
will be applied.
Specifies the
cutoff frequency
of the high pass
filter.
You can set the
gain for the cutoff
frequency (Gc)
when you select
"AdjustGc
(Adjustable Gc)"
for the Type
parameter.
Selects an
attenuation
amount per
octave, and a
type of filter.
If you select
"Thru," no filter
will be applied.
Specifies the
cutoff frequency
of the low pass
filter.
You can set the
gain for the cutoff
frequency (Gc)
when you select
"AdjustGc
(Adjustable Gc)"
for the Type
parameter.
SP2060 Owner's Manual
27