Display Messages - Yamaha S90 Owner's Manual

Messages
Are you sure? [YES]/[NO]
Bad Card.
Bulk protected.
Can't make folder.
Card full.
Card not ready.
Card read/write error.
Card unformatted.
Card write protected.
Completed.
Device number is off.
Device number mismatch.
Effect plug-in is not in slot 1.
Executing...
File not found.
Folder is too deep.
Illegal Card.
Illegal file.
Illegal file name.
MIDI buffer full.
MIDI checksum error.
MIDI data error.
mLAN connection error.
mLAN error (xxx).
mLAN network error.
mLAN now in Mixer mode.
Multi plug-in is not in slot 3.
Not empty folder.
Now checking plug-in board.
Now loading... (xxxx)
Now saving... (xxxx)
Now working...
Overwrite? [YES]/[NO]
Please keep power on.
116

Display Messages

Display Messages
Confirms whether you want to execute a specified operation or not. Press [INC/YES] or [DEC/NO] as
required.
The card is unusable. Format the card and try again.
Bulk data was received when RcvBulk was set to "protect." (Utility [F5] [SF2] Ref. #184)
No more directories can be created below the current level.
The card is full and no more data can be saved. Use a new card, or make space by erasing unwanted
data from the card.
A card is not properly inserted in or connected to the S90.
An error occurred while reading or writing to/from or Memory card.
The card is not formatted, or the format is unusable by the S90. Check the card contents.
The card is write protected.
The specified load, save, format, or other job has been completed.
Bulk data cannot be transmitted/received since the device number is off.
Bulk data cannot be transmitted/received since the device numbers don't match.
The Effect Plug-in board does not work because it has not been installed to slot 1. The Effect Plug-in
board should be installed to slot 1.
Never attempt to turn off the power while data is being written to Flash ROM. Turning the power off in
this state results in loss of all user data and may cause the system to freeze (due to corruption of data in
the Flash ROM).
The specified file was not found on the card during a load operation. Try again after re-inserting/re-
connecting the card.
Directories below this level cannot be accessed.
The format type of the Memory card is wrong.
The file specified for loading is unusable by the S90.
The specified file name is unacceptable. Try entering a different name.
Failed to process the MIDI data because too much data was received at one time.
An error occurred when receiving bulk data.
An error occurred when receiving MIDI data.
Indicates a problem in the mLAN8E connection. Check the on/off status of the LED lamps on the
mLAN8E and refer to the Owner's Manual of the mLAN8E.
Indicates an unspecified problem related to the mLAN8E.
Indicates a problem in the mLAN8E network. Check the on/off status of the LED lamps on the mLAN8E
and refer to the Owner's Manual of the mLAN8E.
The mLAN8E board is set to the Mixer mode by your computer, and the S90 cannot control the
mLAN8E.
The Multi-Part Plug-in board does not work because it has not been installed to slot 3. The Multi-Part
Plug-in board should be installed to slot 3.
You attempt to delete a folder that contains data.
The S90 is checking the Plug-in board installation status when powering the S90 on.
Indicates that a file is being loaded.
Indicates that a file is being saved.
Indicates that the S90 is currently engaged in some operation, such as writing to/reading from the card,
etc.
A save operation will overwrite data on the card, and this message confirms whether it is OK to continue
or not. Press [INC/YES] or [DEC/NO] as required.
Never attempt to turn off the power while data is being written to Flash ROM. Turning the power off in
this state results in loss of all user data and may cause the system to freeze (due to corruption of data in
the Flash ROM).
Information