Display Messages - Yamaha MOXF6 Owner's Manual

Display Messages

LCD indication
All remote templates stored. Appears when you store the Control Template in the Remote mode.
Are you sure? Confirms whether you want to execute a specified operation or not.
Arpeggio memory full. The internal memory for Arpeggio data is full.
Arpeggio type copied. The Arpeggio Types are copied to the [SF1] – [SF6] buttons.
Bad USB device. The USB flash memory device connected to this instrument is unusable. Format the USB flash memory device and try
again.
Bulk protected. Bulk data cannot be received because of the setting in the Utility mode.
Can't undo. OK? When certain Song/Pattern Jobs are executed, internal memory becomes too full for use of the Undo operation.
Completed. The specified load, save, format, or other Job has been completed.
Device number is off. Bulk data cannot be transmitted/received since the device number is off.
Device number mismatch. Bulk data cannot be transmitted/received since the device numbers don't match.
Edited data will be Prompts you to confirm whether or not to erase the edited data.
discarded.
Edits will be stored by Confirms whether or not you want to continue the Load operation. If you select yes, the current edits will be stored.
loading.
Edits will be stored by Confirms whether or not you want to continue the Save operation. If you select yes, the current edits will be stored.
saving.
Empty Favorite! Appears when you press the [FAVORITE] button with no program registered to the Favorite Category.
[SHIFT]+[FAVORITE] to add.
Executing... A format operation or Job is being executed. Please wait.
File already exists. A file having the same name as the one you are about to save already exists.
File not found. The file of the specified type cannot be found.
Folder is too deep. Directories below this level cannot be accessed.
Illegal file name. The specified file name is invalid. Try entering a different name.
Illegal file. The file specified for loading is unusable by this instrument or cannot be loaded in the current mode.
Illegal input. An invalid input or value has been specified. Check the input method or value.
Illegal measure. An invalid measure number has been specified in the Song/Pattern mode. Select the measure again.
Illegal phrase number. An invalid phrase number has been specified in the Pattern mode. Select the phrase again.
Illegal Track number. An invalid Track number has been specified in the Song/Pattern mode. Select the Track again.
Incompatible USB device A USB device which cannot be used with this instrument has been connected to the USB [TO DEVICE] terminal.
MIDI buffer full. Failed to process the MIDI data because too much data was received at one time.
MIDI checksum error. An error occurred when receiving bulk data.
MIDI data error. An error occurred when receiving MIDI data.
Mixing Voice full. The Mixing Voice cannot be stored because the number of Voices already stored has exceeded the maximum capacity.
New Flash Memory Module. This message appears when the Flash Memory Expansion Module (FL512M/FL1024M) which was installed in a different
Please load waveform data. MOXF has been installed to the current MOXF. If this message appears, you should save the Waveform data (including the
parameter settings) of the previous MOXF to a USB storage device, connect the USB storage device to the current MOXF,
then load the Waveform data. This occurs because the Sample without the parameter settings cannot produce the proper
sound.
No data. When a Song/Pattern Job is executed, the selected Track or range contains no data. Select an appropriate Track or range.
In addition, this message appears when a Job related to a Mixing Voice cannot be executed because the specified Mixing
Voice is not available.
No F7 (End of Exc.) Exclusive data has been entered or changed without the necessary "End of Exclusive" byte (F7). Make sure the F7
message is included.
No Flash Memory Module This message appears when no Flash Memory Expansion Module is installed or the unformatted Module has been
installed or module is installed.
unformatted.
No response from USB There is no response from the USB device connected to the USB [TO DEVICE] terminal.
device
No sample data. This message appears when you try loading Waveform data with the "with sample" checkmark removed, even when the
corresponding Sample is not available on the Flash Memory Expansion Module.
Not empty folder You have attempted to delete a folder that contains data.
Not empty waveform. You have attempted to load Waveform data to a Waveform that already contains data.
Description
Appendix
MOXF6/MOXF8 Owner's Manual
63