Yamaha S90 Owner's Manual page 103

Ref.
Display Parameter Name
#
115 OutputSel Output Select
116 (InsEF)
Insertion Effect
117 ElementSw
Controller Set 1-6 Element
Switch
118 Source Controller Set 1-6 Source
119 Dest Controller Set 1-6
Destination
120 Depth Controller Set 1-6 Depth
121 Filter
MW/AT(CAT)/AC(AC1)
Filter Control
122 PMod
MW/AT(CAT)/AC(AC1)
LFO Pitch Modulation
Depth
123 FMod
MW/AT(CAT)/AC(AC1)
LFO Filter Modulation
Depth
124 AMod
MW/AT(CAT)/AC(AC1)
LFO Amplitude Modulation
Depth
125 Pitch (AT)
AT (CAT) Pitch Control
126 Src AC Source
(AC1 Control Number)
127 (ARP) Switch/Hold
Arpeggio Switch/Hold
Control Number
128 ASA/ASB
Assignable A/B Slider
Control Number
129 Dest
Assignable A/B Slider
Destination
130 FS FS Control Number/
FS Function Assignment
131 Set Remote Set Remote Mode
Template Type
Template Type
132 BankMSB/LSB Bank Select MSB/LSB
133 PgmChange
Program Change
(Program Number 1-128)
134
CtrlSlider Control Slider Control
Number
135 Level Element Level
Determines the specific output(s) for the individual part (Performance/Mixing Part Edit). Determines the specific output(s) for the
individual Drum key signal (Drum Key Edit).
Indicates whether the Insertion effect is applied or not for each part. This is for display purposes only and cannot be set here.
Determines whether or not the selected controller affects each individual element.
"-"...disabled.
Determines which panel controller is to be assigned and used for the selected Set. This controller then is used to control the
parameter set in Destination below.
Determines the parameter that is controlled by the Source
controller (above).
Determines the degree to which the Source controller affects the Destination parameter.
Determines the depth of control of the Modulation Wheel ([SF2])/Aftertouch ([SF3])/Assignable Controller ([SF4]) over the filter cutoff
frequency.
Determines the depth of control of the Modulation Wheel ([SF2])/Aftertouch ([SF3])/Assignable Controller ([SF4]) has over pitch
modulation (vibrato effect).
Determines the depth of control of the Modulation Wheel ([SF2])/Aftertouch ([SF3])/Assignable Controller ([SF4]) has over filter cutoff
modulation (wah effect).
Determines the depth of control of the Modulation Wheel ([SF2])/Aftertouch ([SF3])/Assignable Controller ([SF4]) has over amplitude
modulation (tremolo effect).
Determines the depth of control of keyboard aftertouch over pitch. You can set a value (in semitones) of up to two octaves.
Determines the MIDI Control number used to control the filter, PMod, FMod, and Amod.
Determines the Control Number that controls the Arpeggio playback on/off and Arpeggio Hold on/off.
Determines the Control number to be controlled by the ASSIGN A/B sliders. This is available when controlling an external MIDI
device.
Determines the function to be controlled by the Control Change number set above. See the separate Data List.
Assign a specific function and control number to the Footswitch.
Select the template for your particular sequence software.
Select the Voice for each zone by specifying these three MIDI messages. Refer to the Voice List in the separate Data List.
Determine which Control numbers are used for the Sliders for each zone. These settings are available only when the ZoneSwitch
(Master Play Mode [F2] ) is set to on and the CONTORL FUNCTION on the panel is set to "zone."
Adjusts the output level for the selected Element/drum key, letting you control the level balance among the Elements/keys.
Appendix
Explanation
Reference Quick Guide
Related
Page
*16
*46
55 *47
*48
55
*49
55 *50
55
*50
56 *51
57
53 *6
Basics Section