Yamaha S90 Owner's Manual page 101

Ref.
Display Parameter Name
#
70 PitchSens Pitch Key Follow Sensitivity Determines the sensitivity of the Key Follow effect (the interval of adjacent notes). At +100, adjacent notes are pitched one semitone
71 CenterKey
Pitch Key Follow Center
Key
72 EGTimeSens
PEG Time Key Follow
Sensitivity
73 CenterKey PEG Time Key Follow
Center Key
74 Bank Arpeggio Type Bank
75 Type
Arpeggio Type
76 Tempo
Arpeggio Tempo
77 Switch (ArpSwitch) Arpeggio Switch
78 Hold
Arpeggio Hold
79 KeyMode
Arpeggio Key Mode
80 VelMode Arpeggio Velocity Mode
81 NoteLimit
Arpeggio Note Limit Low/
High
82 VelocityLimit
Arpeggio Velocity Limit
Low/High
83 UnitMultiply Arpeggio Unit Multiply
84 VelocityRate Arpeggio Velocity Rate
85 GateTimeRate Arpeggio Gate Time Rate
86 OutputSwitch
Arpeggio MIDI Out Switch
87 TransmitCh
Arpeggio MIDI Transmit
Channel
88 BC/AS1/AS2/ BC/Assign1/Assign2/FC1/
FC1/FC2
FC2
Control Number
89 (Transmit Switch) Transmit Switch
90 Type
Filter Type
(100 cents) apart. At 0, all notes are the same pitch (for the percussion sounds,etc.). At +50, one octave is stretched out over twenty-
four notes. For negative values, the settings are reversed.
Determines the basic pitch (note number) used by the PitchSens parameter (above). The note number in this setting is the same
pitch as normal (100%).
Determines the sensitivity of the PEG time (the speed of the PEG change) to velocity.
Determines the basic pitch (note number) used by the EGTimeSens parameter (above). When the center note is played, the PEG
time behaves according to its actual settings. For other notes, the speed varies in proportion to the key played and its interval away
from the center key.
Determines the Arpeggio bank.
pre1: preset 1, pre2: preset 2, user: User Arpeggio data (page 83) saved by MOTIF series (when loaded from a Memory Card)
Determines the Arpeggio type. The two-letter prefix before the name indicates the general Arpeggio category.
Determines the Arpeggio Tempo. When MIDI sync (Utility [F5] [SF3]) is turned on, "MIDI" is displayed here and cannot be set. In
the Sequence Play mode, the tempo is synchronized to that of the song (page 76).
Determines whether Arpeggio is on or off. You can control the switch by using the Foot Switch (Utility [F4] [SF3] FS=96).
Determines whether Arpeggio playback is "held" or not. When set to "on," the Arpeggio cycles automatically, even if you release
your fingers from the keys, and it continues to cycle until the next key is pressed. You can control this setting by using the Foot
Switch (Utility [F4] [SF3] FS=97).
Determines how the Arpeggio plays back when playing the keyboard.
Determines the playback velocity of the Arpeggio, or how it responds to your own playing strength.
Determines the lowest and highest notes in the Arpeggio's note range.
Determines the lowest and highest velocity in the Arpeggio's velocity range. This lets you control when the Arpeggio sounds by your
playing strength.
Adjust the Arpeggio playback time. For example, if you set a value of 200%, the playback time will be doubled and the tempo
halved. If you set a value of 50%, the playback time will be halved and the tempo doubled.
Determines how much the Velocity of the Arpeggio playback is offset from the original value. For example, a setting of 100% means
the original values are used.
Determines how much the Gate Time (length) of the Arpeggio notes is offset from the original value. A setting of 100% means the
original values are used.
When set to on, Arpeggio playback data is output from the MIDI terminal.
Determines the MIDI transmit channel for Arpeggio playback data.
KbdCh...Arpeggio playback data is transmitted by KBDTransCh ([F5] [SF1] Keyboard Transmit Channel) in the Utility mode
(Performance/Mixing)
Sets the control number for the Breath Controller (BC), Assign 1/2 sliders (AS1/2), and Foot Controllers 1/2 (FC1/2).
When the relevant parameter is set to "on," playing the selected zone will transmit the corresponding MIDI data, such as Control
Change and Program Change messages. Pressing the [F5] button switches between display of all four Zones and one single Zone
(in which all transmit channel settings are shown). In the four-Zone display, use the cursor buttons to scroll.
Determines the filter type. The parameters differ depending on the selected type.
Appendix
Explanation
Reference Quick Guide
Related
Page
*28
*28
*12
*28
*28
*12
45 *29
*29
45
*34
45
45 *30
45 *31
*32
*33
*34
*35
*36
*12
47 *13
*37
*38
*37
*39
53 *40
63 *41
Basics Section