Milnor MWF63C7 Installation And Service
  1. Manuals
  2. Brands
  3. Milnor Manuals
  4. Washer
  5. MWF63C7
  6. Installation and service

Milnor MWF63C7 Installation And Service

Hide thumbs Also See for MWF63C7:
Table of Contents

Advertisement

Quick Links

Published Manual Number/ECN: MPIMWFC7AE/2018215A
• Publishing System: TPAS2
• Access date: 05/28/2018
• Document ECNs: Latest
Installation and Service
MWF63C7, MWF63Y7
MWF77C7, MWF77Y7
Washer Extractors
PELLERIN MILNOR CORPORATION
POST OFFICE BOX 400, KENNER, LOUISIANA 70063-0400, U.S.A.

Advertisement

Table of Contents
loading

Related Manuals for Milnor MWF63C7

Summary of Contents for Milnor MWF63C7

  • Page 1 Published Manual Number/ECN: MPIMWFC7AE/2018215A • Publishing System: TPAS2 • Access date: 05/28/2018 • Document ECNs: Latest Installation and Service MWF63C7, MWF63Y7 MWF77C7, MWF77Y7 Washer Extractors PELLERIN MILNOR CORPORATION POST OFFICE BOX 400, KENNER, LOUISIANA 70063-0400, U.S.A.

  • Page 3: Table Of Contents

    MWF63_, MWF77_ BMP150057/2018195A Safety Placards and Locations - MWF27_, MWF45_, MWF63_, MWF77_ BMP130066/2018195A 1. Installation Washer-Extractor Installation BIMUUI01/20030213 About the Forces Transmitted by Milnor® Washer-extractors BIWUUI02/20001108 Shipping Brackets BPWCDJ03/2019197A Guards and Covers BPWCDM01/2018195A Prevent Damage from Chemical Supplies and Chemical Systems BIWUUI03/2017353A 2.

  • Page 4: Mpimwfc7Ae/18215A

    Table of Contents, continued MPIMWFC7AE/18215A Page Description Document Peristaltic Supply BMP130080/2018195A 5 Compartment Supply BMP130081/2018195A 9. Dimensional Drawings Dimensional Drawing - MWF63C7, MWF63Y7 BDMWF63CY7BE/2018215D Dimensional Drawing - MWF77CY, MWF77Y7 BDMWF77CY7BE/2018215D...

  • Page 5: Limited Standard Warranty

    (unless the time period is specifically extended for certain parts pursuant to a specific MILNOR published extended warranty) from our factory with no operating hour limitation. This warranty is contingent upon the equipment being installed, operated and serviced as specified in the operating manual supplied with the equipment, and operated under normal conditions by competent operators.

  • Page 6: How To Get The Necessary Repair Components

    • If the component is an electrical component, give the schematic number if known. • If the component is a motor or an electrical control, give the nameplate data from the used component. To write to the Milnor factory: Pellerin Milnor Corporation Post Office Box 400...

  • Page 7: Trademarks

    BNUUUU02 / 2017285A BNUUUU02 0000158094 A.3 7/13/17 1:53 PM Released Trademarks BNUUUU02.R01 0000158093 A.2 7/13/17 1:11 PM Released These words are trademarks of Pellerin Milnor Corporation and other entities: Table 1 Trademarks AutoSpot™ GreenTurn™ Milnor® PulseFlow® CBW® GreenFlex™ MilMetrix® PurePulse®...
  • Page 8 Paper tags on the machine provide installation guidelines and precautions. The tags can be tie-on or adhesive. You can remove tie-on tags and white, adhesive tags after installation. Yellow adhesive tags must remain on the machine. PELLERIN MILNOR CORPORATION...
  • Page 9 Read the manuals before proceeding. This symbol appears on most tags. The machine ships with safety, operator, and routine maintenance guides for customer use. Milnor dealer manuals for installing, servicing, and commissioning this machine are also available from the Milnor Parts department.
  • Page 10 A tag will also appear on the restraint to help identify it. Most, but not all shipping restraints display the color red. Some shipping restraints are also safety stands. Do not discard these. PELLERIN MILNOR CORPORATION...
  • Page 11 B2T2003001: Hold the side of the connection stationary with a wrench as you tighten the connection with another wrench. Otherwise, you may twist components, such as valves, damaging them. B2T2004027: Steam connection (optional) — End of BIUUUI02 — PELLERIN MILNOR CORPORATION...

  • Page 12: Safety-Tilting Washer-Extractors

    The owner/user must familiarize himself with the contents of all machine instruction manuals. The owner/user should direct any questions about these instructions to a Milnor® dealer or the Milnor® Service department.
  • Page 13 The Safety Guide and other machine manuals must be available at all times to the appropriate personnel. See the machine service manual for safety placard part numbers. Contact the Milnor Parts department for replacement placards or manuals. Maintenance —Ensure the machine is inspected and serviced in accordance with the norms of 1.5.
  • Page 14 The following are instructions about hazards related to the cylinder and laundering process. DANGER 7 : Entangle and Sever Hazards—Contact with goods being processed can cause the goods to wrap around your body or limbs and dismember you. The goods are normally isolated by the locked cylinder door. PELLERIN MILNOR CORPORATION...
  • Page 15 • Do not operate the machine with any evidence of damage or malfunction. PELLERIN MILNOR CORPORATION...
  • Page 16 • Do not tamper with or disable any safety device or operate the machine with a malfunctioning safety device. Request authorized service. • Do not operate a damaged or malfunctioning machine. Request authorized service. • Do not attempt unauthorized servicing, repairs, or modification. PELLERIN MILNOR CORPORATION...
  • Page 17 Hazards include but are not limited to panic, burns, poisoning, suffocation, heat prostration, biological contamination, electrocution, and crushing. • Do not enter the cylinder until it has been thoroughly purged, flushed, drained, cooled, and immobilized. — End of BIUUUS27 — PELLERIN MILNOR CORPORATION...
  • Page 18 Safety Placards and Locations- ISO MWF27J8, MWF27Z8; MWF45J8, MWF45Z8; MWF63J7, MWF63Z7; MWF77J7, MWF77Z7 MWF63C7, MWF63Y7; MWF77C7, MWF77Y7 If the placard is removed or you cannot read it, replace the placard immediately. If the placard is aluminum, the mounting holes are on the machine. Use self-tapping screws.
  • Page 19 BMPXX/XXA BMP150057/2018195A Page (x / x) Page (2 / 3) Safety Placards and Locations- ISO MWF27J8, MWF27Z8; MWF45J8, MWF45Z8; MWF63J7, MWF63Z7; MWF77J7, MWF77Z7 MWF63C7, MWF63Y7; MWF77C7, MWF77Y7 MWF63J7, MWF63Z7 MWF77J7, MWF77Z7 (alternate location) Front View Rear View MWF63 7, MWF63 7...
  • Page 20 Safety Placards and Locations- ISO MWF27J8, MWF27Z8; MWF45J8, MWF45Z8; MWF63J7, MWF63Z7; MWF77J7, MWF77Z7 MWF63C7, MWF63Y7; MWF77C7, MWF77Y7 Parts List Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In"...
  • Page 22 Safety Placards and Locations- MWF27J8, MWF27Z8; MWF45J8, MWF45Z8; MWF63J7, MWF63Z7; MWF77J7, MWF77Z7 MWF63C7, MWF63Y7; MWF77C7, MWF77Y7 If the placard is removed or you cannot read it, replace the placard immediately. If the placard is aluminum, the mounting holes are on the machine. Use self-tapping screws.
  • Page 23 BMPXX/XXA BMP130066/2018195A Page (2 / 3) Safety Placards and Locations- MWF27J8, MWF27Z8; MWF45J8, MWF45Z8; MWF63J7, MWF63Z7; MWF77J7, MWF77Z7 MWF63C7, MWF63Y7; MWF77C7, MWF77Y7 MWF63J7, MWF63Z7 MWF77J7, MWF77Z7 (alternate location) Front View Rear View MWF63 7, MWF63 7 MWF77C7, MWF77Y7 Front View...
  • Page 24 Safety Placards and Locations- MWF27J8, MWF27Z8; MWF45J8, MWF45Z8; MWF63J7, MWF63Z7; MWF77J7, MWF77Z7 MWF63C7, MWF63Y7; MWF77C7, MWF77Y7 Parts List Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In"...

  • Page 25: Installation

    Installation...
  • Page 26 Do not hesitate to file a claim with the carrier if the machine is damaged in any way during shipment. Milnor will be glad to assist you in filing your claim, but is not responsible for any shipping damage to the machine once it has been delivered to the carrier in good condition.
  • Page 27 GQcXUb5hdbQSd_b 9^cdQ\\QdY_^ Figure 1: Vibration warning 20DC8>= ) <PRWX]T 3P\PVT 7PiPaSb —Improperly installed suspension type machines can “walk” out of position during extract, endangering personnel and damaging equipment. • Roughen floor. Install anchor bolts and grout under all base pads to prevent “teeter-totter” and sideways movement.
  • Page 28 • Remove the red shipping bracket stands. • Remove the tie wrap that secures the vibration safety switch. • Check the perforated cylinder for smoothness before placing machine in service. Milnor cannot accept cylinder finish damage claims after machine is in service.

  • Page 29: About The Forces Transmitted By Milnor® Washer-Extractors

    • the liquor level and chemical conditions in the bath preceding extraction, and • other miscellaneous factors. ® Estimates of the maximum force normally encountered are available for each Milnor model and ® size upon request. Floor or foundation sizes shown on any Milnor...
  • Page 30 All data is subject to change without notice and may have changed since last printed. It is the sole responsibility of every potential owner to obtain written ® confirmation that any data furnished by Milnor applies for the model(s) and serial number(s) of the specific machines.

  • Page 31: Shipping Brackets

    BPWCDJ03 / 2018197A BPWCDJ03 0000184050 5/7/18 7:45 AM Released Shipping Brackets 1 of 2 MWF63C7, MWF63Y7, MWF77C7, MWF77Y7 BPWCDJ03.R01 0000184049 B.2 5/7/18 7:45 AM Released Figure 1. Installed Views Legend Section View of Shipping Brackets Typical hardware Pellerin Milnor Corporation...
  • Page 32 Released Shipping Brackets 2 of 2 MWF63C7, MWF63Y7, MWF77C7, MWF77Y7 Table 1 Parts List— Find the assembly for your machine and the letter shown in the "Item" column. The components for your machine will show this let- ter or the word "all" in the "Used In" column. The numbers shown in the "Item" column are those shown in the illustrations.

  • Page 33: Guards And Covers

    Released Guards and Covers 1 of 2 MWF63C7, MWF63Y7, MWF77C7, MWF77Y7 BPWCDM01.R01 0000183826 A.2 A.4 5/2/18 1:15 PM Released Table 1 Parts List— Find the assembly for your machine and the letter shown in the "Item" column. The components for your machine will show this let- ter or the word "all"...
  • Page 34 Released Guards and Covers 2 of 2 MWF63C7, MWF63Y7, MWF77C7, MWF77Y7 Table 2 Parts List— Find the assembly for your machine and the letter shown in the "Item" column. The components for your machine will show this let- ter or the word "all" in the "Used In" column. The numbers shown in the "Item" column are those shown in the illustrations.

  • Page 35: Prevent Damage From Chemical Supplies And Chemical Systems

    The company that does these procedures must make sure that these procedures do not cause dam- age. Pellerin Milnor Corporation accepts no responsibility for chemical damage to the ma- chines it makes or to the goods in a machine.
  • Page 36 Figure 1. Incorrect Configurations That Let the Chemical Supply Go In the Machine by a Siphon Schematic Views Legend Pump Chemical tank The siphon occurs above here. Liquid in the gray parts of the chemical tube and tank can go in the machine. Pellerin Milnor Corporation...
  • Page 37 BNUUUR02.R02 0000160545 A.2 A.8 8/30/17 3:28 PM Released Use the chemical manifold supplied. There is a manifold on the machine to attach chemical tubes from a chemical pump system. The manifold has a source of water to flush the chemical supplies with water. Pellerin Milnor Corporation...
  • Page 38 Figure 4. A Configuration that Prevents Flow in the Machine When the Pump is Off (if the chemical tube and tank have no pressure) Schematic View Legend Chemical inlet on the machine Chemical tube Pump Chemical tank Pellerin Milnor Corporation...
  • Page 39 Prevent leaks. When you do maintenance on the chemical pump system: • Use the correct components. • Make sure that all connections are the correct fit. • Make sure that all connections are tight. End of document: BNUUUR02 Pellerin Milnor Corporation...

  • Page 41: 37 2. Service And Maintenance

    Service and Maintenance...

  • Page 42: Service Connections

    Figure 1: Flush water valve pressure regulator CAUTION 2 : Machine Damage Hazards—Pumped chemical systems, if not properly installed, can cause corrosion damage. • See the reference manual for precautions and additional information before making any chemical connections. PELLERIN MILNOR CORPORATION...
  • Page 43 5. Make power and liquid supply electrical connections within junction boxes on the rear of the machine. 6. Verify motor rotation (Figure 2). See the operating and trouble shooting manual for more information. If the cylinder turns in the wrong direction, interchange the wires connected to PELLERIN MILNOR CORPORATION...
  • Page 44 Remove Shipping Restraints Remove all shipping restraints (usually marked in red). Restraints may be located behind access panels. Restraints may include the vibration switch restraint (Figure 4). Figure 4: Typical Vibration Switch Showing Restraint in Place PELLERIN MILNOR CORPORATION...
  • Page 45 Service Connections Check Cylinder Surface Check the perforated cylinder for smoothness. Milnor will not accept responsibility for the cylinder finish after the machine is placed in service. — End of BIMUUI02 — PELLERIN MILNOR CORPORATION...

  • Page 46: Torque Requirements For Fasteners

    These tables give the standard dimension, grade, threadlocker, and torque requirements for ® fasteners frequently used on Milnor equipment. ® Note 1: Data from the Pellerin Milnor Corporation “Bolt Torque Specification” (bolt_torque_milnor.xls/2002096). Fasteners Made of Carbon Steel 1.1. Without a Threadlocker 1.1.1.
  • Page 47 Table 3: Torque Values for Plated Fasteners with Maximum 5/16-inch Diameters and No Lubricant The Grade of the Bolt Grade 2 Grade 5 Grade 8 Grade BC Dimension Pound-Inches Pound-Inches Pound-Inches Pound-Inches 1/4 x 20 1/4 x 28 5/16 x 18 5/16 x 24 PELLERIN MILNOR CORPORATION...
  • Page 48 Specific applications sometime require that a LocTite product is applied to a bolt size outside the ranges shown here. For example, Milnor specifies LocTite 242 for use on certain 1" bolt applications and has confirmed this usage with the LocTite manufacturer. You may see variances such as this in the documentation for specific machine assemblies.
  • Page 49 Table 8: Torque Values if You Apply LocTite 262 The Grade of the Bolt Grade 2 Grade 5 Grade 8 Grade BC Dimension Pound-feet Pound-feet Pound-feet Pound-feet 3/4 x 10 3/4 x 16 7/8 x 9 7/8 x 14 PELLERIN MILNOR CORPORATION...
  • Page 50 1.2. Table 11: Torque Values for Stainless Steel Fasteners 5/16-inch and Smaller 18-8 Stainless with 316 Stainless 18-8 Stainless Loctite 767 Pound-Inc Pound-Inc Pound-Inc Dimension 1/4 x 20 1/4 x 28 5/16 x 18 5/16 x 24 PELLERIN MILNOR CORPORATION...
  • Page 51 CAUTION 3 : Malfunction Hazard—Heat, vibration, or mechanical shocks can let the fasteners loosen if you do not apply the threadlocker correctly. Loose fasteners can cause malfunctions of the equipment. • Read the threadlocker manufacturer's instructions and warnings. Obey these instructions. PELLERIN MILNOR CORPORATION...
  • Page 52 No threadlocker here Apply the threadlocker to this area Nut depth Disassembly —For high-strength threadlocker, apply heat for five minutes. Disassemble with 3.3. hand tools while the parts are hot. For low-strength and moderate-strength threadlocker, disassemble with hand tools. PELLERIN MILNOR CORPORATION...
  • Page 53 Torque Requirements for Fasteners Figure 4: Disassembly Apply Heat to a Small Area Legend How to apply heat to a small fastener How to apply heat to a large fastener — End of BIUUUM04 — PELLERIN MILNOR CORPORATION...

  • Page 55: Drive Assemblies Drive

    Drive Assemblies...
  • Page 56 Drive MWF63J , MWF63Z , 7 MWF77J7, MWF77Z7 MWF63C7, MWF63Y7, MWF77C7, MWF77Y7 3,4,5 Parts List—Drive Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In"...

  • Page 57: Bearing Assembly & Installation Mwf45, Mwf63, Mwf77

    BPWMCB01 / 2017366A BPWMCB01 0000161056 12/7/17 3:32 PM Released Bearing Assembly & Installation MWF45, MWF63, MWF77 1 of 6 BPWMCB01.R02 0000161885 A.3 A.2 12/7/17 4:37 PM Released Figure 1. Lubrication Lines Pellerin Milnor Corporation...
  • Page 58 BPWMCB01 / 2017366A BPWMCB01 0000161056 12/7/17 3:32 PM Released Bearing Assembly & Installation MWF45, MWF63, MWF77 2 of 6 Figure 2. Shell Cross-section Legend Top connection between the shell front and the shell side sheet Connection between the shell rear and the bearing housing Connection between the cylinder rear and the bearing housing...
  • Page 59 3 of 6 Figure 4. Shell Cross-section Details D and E Legend Connection between the cylinder rear and the bearing housing Connection between the bearing housing and the pulley Apply adhesive to the bolt, torque to 282 FT. LBS. Pellerin Milnor Corporation...
  • Page 60 BPWMCB01 / 2017366A BPWMCB01 0000161056 12/7/17 3:32 PM Released Bearing Assembly & Installation MWF45, MWF63, MWF77 4 of 6 Figure 5. Bearing Housing Cross-section and Details...
  • Page 61 54AT101190 TIMK HH221449/HH221410=4"BORE 98MW3611 MACH=MAIN SHAFT MWF45 98MW4211 MACH=MAIN SHAFT MWF77 98CMCR3612 MACH=FRONT SEAL HOLDER 36X 98CMCR4214 MACH=FRONT SEAL HOLDER 42X 98CMCR3613 SEAL SLEEVE=BRG ASSY 36X 98CMCR4215 SEAL SLEEVE=BRG ASSY 42X 02 21542 FRONT GREASE SHIELD 3630F Pellerin Milnor Corporation...
  • Page 62 BPWMCB01 / 2017366A BPWMCB01 0000161056 12/7/17 3:32 PM Released Bearing Assembly & Installation MWF45, MWF63, MWF77 6 of 6 Find the assembly for your machine and the letter shown in the "Item" column. The components for your machine will show this letter or the word "all"...

  • Page 63: Suspension

    Suspension...
  • Page 64 BPWCDJ01 0000183866 5/9/18 9:13 AM Released Suspension 1 of 2 MWF63C7, MWF63Y7, MWF77C7, MWF77Y7 BPWCDJ01.R01 0000183865 B.3 5/9/18 9:13 AM Released Figure 1. Marshmellow Springs Legend Left Side View MWF63C7 Left Side View MWF77C7 Detailed View, Cable Tie Down, Typical 2 places...
  • Page 65 Released Suspension 2 of 2 MWF63C7, MWF63Y7, MWF77C7, MWF77Y7 Table 1 Parts List— Find the assembly for your machine and the letter shown in the "Item" column. The components for your machine will show this let- ter or the word "all" in the "Used In" column. The numbers shown in the "Item" column are those shown in the illustrations.

  • Page 66: Shocks

    BPWCDJ02 / 2018197A BPWCDJ02 0000183936 5/7/18 7:39 AM Released Shocks 1 of 1 MWF63C7, MWF63Y7, MWF77C7, MWF77Y7 BPWCDJ02.R01 0000183935 C.2 5/7/18 7:39 AM Released Figure 1. Installed Views Legend Rear Shocks Front Shocks Table 1 Parts List— Find the assembly for your machine and the letter shown in the "Item" column. The components for your machine will show this letter or the word "all"...

  • Page 67: 63 5. Shell And Door Assemblies

    Shell and Door Assemblies...
  • Page 68 BMP130086/2018195A Page (1 / 4) Door 26” MWF63J , MWF63Z , 7 MWF77J7, MWF77Z7 MWF63C7, MWF63Y7, MWF77C7, MWF77Y7 PELLERIN MILNOR CORPORATION PELLERIN MILNOR CORPORATION...
  • Page 69 BMP130086/2018195A Page (2 / 4) Door 26” MWF63J , MWF63Z , 7 MWF77J7, MWF77Z7 MWF63C7, MWF63Y7, MWF77C7, MWF77Y7 PELLERIN MILNOR CORPORATION PELLERIN MILNOR CORPORATION...
  • Page 70 BMP130086/2018195A Page (3 / 4) Door 26” MWF63J , MWF63Z , 7 MWF77J7, MWF77Z7 MWF63C7, MWF63Y7, MWF77C7, MWF77Y7 Section Section Section Section Section Section PELLERIN MILNOR CORPORATION...
  • Page 71 Door 26” MWF63J , MWF63Z , 7 MWF77J7, MWF77Z7 MWF63C7, MWF63Y7, MWF77C7, MWF77Y7 Parts List—Door 26” Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In"...

  • Page 72: Door Latch

    Door Latch MWF45J8, MWF45Z8, MWF63J7, MWF63Z7, MWF77J7, MWF77Z7 MWF63C7, MWF63Y7, MWF77C7, MWF77Y7 Parts List—Door Latch Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In"...

  • Page 73: Door Open Lock

    5/8/18 7:32 AM Released Door Open Lock 1 of 1 MWF63C7, MWF63Y7, MWF77C7, MWF77Y7 BPWCDD01.R01 0000184147 A.3 A.4 5/8/18 7:32 AM Released Figure 1. Door Open Lock and Secondary Door Switch (Tilt Models) Table 1 Parts List— Find the assembly for your machine and the letter shown in the "Item" column. The components for your machine will show this let- ter or the word "all"...
  • Page 75 Water and Steam Piping and Assemblies...

  • Page 76: Water And Steam

    BMP130087/2018195A Page (1 / 3) Water and Steam MWF63J8, MWF63Z8, MWF63C7, MWF63Y7, MWF77J8, MWF77Z8, MWF77C7, MWF77Y7 Shell Tilt Models Shell Non-Tilt Models Soap Chute or Hot water 5 Compartment Supply for supply Cold Steam Drain trough PELLERIN MILNOR CORPORATION...
  • Page 77 BMP130087/2018195A Page (2 / 3) Water and Steam MWF63J8, MWF63Z8, MWF63C7, MWF63Y7, MWF77J8, MWF77Z8, MWF77C7, MWF77Y7 Hot water for supply Cold Steam Steam Water from Peristaltic PELLERIN MILNOR CORPORATION...
  • Page 78 Page (3 / 3) Water and Steam MWF63J8, MWF63Z8, MWF63C7, MWF63Y7, MWF77J8, MWF77Z8, MWF77C7, MWF77Y7 Parts List—Water and Steam Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In"...

  • Page 79: Drain Valve 4 Inch

    "all" in the "Used In" column. The numbers shown in the "Item" column are those shown in the illustrations. Description/Nomenclature Used In Item Part Number Comments Components A14 06500 *DUMP VALVE ASSY=4"NPT SS Pellerin Milnor Corporation...

  • Page 81: 77 7. Pneumatic Assemblies

    Pneumatic Assemblies...

  • Page 82: Pneumatic Schematic

    BMP180006/2018195A Page (1 / 2) Pneumatic Schematic MWF63C7, MWF63Y7, MWF77C7, MWF77Y7 Figure 1: Schematic Diagram PELLERIN MILNOR CORPORATION PELLERIN MILNOR CORPORATION PELLERIN MILNOR CORPORATION...
  • Page 83 BMP180006/2018195A Page (2 / 2) Pneumatic Schematic MWF63C7, MWF63Y7, MWF77C7, MWF77Y7 Parts List Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In" column to identify which components belong to an assembly. The item numbers (1, 2, 3, etc.) assigned to components relate the parts list to the illustration.

  • Page 85: 81 8. Chemical Supply Devices

    Chemical Supply Devices...

  • Page 86: Soap Chute

    BMP130079/2018195A Page (1 / 2) Soap Chute MWF45J8, MWF45Z8, MWF63J7, MWF63Z7, MWF77J7, MWF77Z7 MWF63C7, MWF63Y7, MWF77C7, MWF77Y7 PELLERIN MILNOR CORPORATION...
  • Page 87 Soap Chute MWF45J8, MWF45Z8, MWF63J7, MWF63Z7, MWF77J7, MWF77Z7 MWF63C7, MWF63Y7, MWF77C7, MWF77Y7 Parts List—Soap Chute Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In"...
  • Page 88 BMP130080/2018195A Page (1 / 2) Peristaltic Supply MWF45J8, MWF45Z8, MWF63J7, MWF63Z7, MWF77J7, MWF77Z7 MWF63C7, MWF63Y7, MWF77C7, MWF77Y7 Figure 1: Peristaltic Diagram View A-A Cross section Cold water line Hot water line Hot water to flush the chemical supplies Water and chemical supplies to the shell Hot and cold water to the shell Apply adhesive to the surfaces that connect.
  • Page 89 BMP130080/2018195A Page (2 / 2) Peristaltic Supply MWF45J8, MWF45Z8, MWF63J7, MWF63Z7, MWF77J7, MWF77Z7 MWF63C7, MWF63Y7, MWF77C7, MWF77Y7 Figure 2: Peristaltic Inlet Cross Section Legend BB. Cross section Vent Air space: 1 inch(25MM) Parts List—Peristaltic Supply Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In"...
  • Page 90 BMP130081/2018195A Page (1 / 2) 5 Compartment Supply MWF45J8, MWF45Z8, MWF63J7, MWF63Z7, MWF77J7, MWF77Z7 MWF63C7, MWF63Y7, MWF77C7, MWF77Y7 PELLERIN MILNOR CORPORATION PELLERIN MILNOR CORPORATION...
  • Page 91 5 Compartment Supply MWF45J8, MWF45Z8, MWF63J7, MWF63Z7, MWF77J7, MWF77Z7 MWF63C7, MWF63Y7, MWF77C7, MWF77Y7 Parts List—5 Compartment Supply Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In"...
  • Page 93 Dimensional Drawings...

This manual is also suitable for:

Mwf63y7Mwf77c7Mwf77y7Mwf27j8Mwf27z8Mwf45j8 ... Show all

Table of Contents