Table of Contents
Advertisement
Quick Links
Universal Sunshade
Groundsmaster
Turf Sprayer
Model No. 30669
Model No. 30671
Important:
If you install the Universal Sunshade on a Reelmaster 3100 traction unit or a Groundsmaster
3500/3505 traction unit, install the Wheel Weight Kit. Contact your authorized Toro distributor for
the correct Wheel Weight Kit.
Safety
General
Before Operating
1.
Review and understand the contents of the
Installation Instructions before installing the
sunshade.
2.
Keep all shields, safety devices and decals
in place. If a shield, safety device or decal
is defective, illegible, or damaged, repair or
replace it before operating the machine.
3.
Do not weld, cut, drill, modify, or remove the roll
bar in any manner.
4.
Tighten any loose nuts, bolts, or screws to
ensure that the machine is in safe operating
condition.
While Operating
1.
Use extreme care when working close to fences,
ditches, or on hillsides.
2.
Check carefully for overhead clearances (i.e.,
branches, doorways, electrical wires) before
driving under any objects and do not contact
them.
3.
Tie down the sunshade frame when transporting
the machine.
4.
Wear hearing protection when operating any
machine with a sunshade.
© 2019—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
or Reelmaster
Maintenance and Service
Register at www.Toro.com.
®
Traction Units or Multi Pro
1.
Before servicing or making adjustments, lower
the implement, shut off the engine, engage the
parking brake, and remove the key.
2.
Make sure that the machine is in safe operating
condition by keeping all nuts, bolts, and screws
tight.
3.
When working on the sunshade installation,
wear eye protection.
4.
Replace a damaged sunshade. Do not repair
or revise.
5.
When installing the sunshade or performing
service, use correct supports, hoists, and jacks.
If the sunshade is not properly supported, it may
move or fall, which may result in personal injury.
6.
To ensure optimum performance and safety,
always purchase genuine Toro replacement
parts and accessories. Replacement parts and
accessories made by other manufacturers could
be dangerous. Such use could void the product
warranty of The Toro Company.
Original Instructions (EN)
All Rights Reserved *3434-434* A
Printed in the USA
Form No. 3434-434 Rev A
®
1750
Installation Instructions
Advertisement
Table of Contents
Related Manuals for Toro 30669
Summary of Contents for Toro 30669
- Page 1 Installation Instructions Important: If you install the Universal Sunshade on a Reelmaster 3100 traction unit or a Groundsmaster 3500/3505 traction unit, install the Wheel Weight Kit. Contact your authorized Toro distributor for the correct Wheel Weight Kit. Safety Maintenance and Service...
-
Page 2: Table Of Contents
Safety and Instructional Decals Safety and instruction decals are affixed to your sunshade. If any decal becomes illegible or damaged, install a new decal. decal98-4387 98-4387 1. Warning—wear hearing protection. Installation Loose Parts Use the chart below to verify that all parts have been shipped. Description Qty. - Page 3 Preparing the Machine Installing the Sunshade Park the machine on a level surface. Groundsmaster 5900 Machine Lower the cutting units and engage the parking Position the ROPS-mount bracket onto the top brake. of the traction unit roll bar (Figure Shut off the engine and remove the key. Note: Make sure that the roll bar is centered Note:...
- Page 4 Tighten all the remaining flange nuts as follows: • Torque the flange nuts (3/8 inch) 41 to 55 N∙m (34 to 41 ft-lb). • Torque the flange nuts (1/2 inch) 113 to 141 N∙m (84 to 104 ft-lb). While aligning the mounting holes, position the sunshade onto the frame as shown in Figure g246184...
-
Page 5: Bolt (3/4 X 4 Inches)
Installing the Sunshade Position the ROPS-mount bracket onto the top of the turf sprayer roll bar (Figure Groundsmaster 3200 or 3300 Note: Make sure that the roll bar is centered in the ROPS-mount bracket. Machine With the roll bar in the raised position, remove the hairpin cotters and the 2 pins (Figure g246185... - Page 6 On each side of the sunshade frame, loosely flange nuts, securing the mounting brackets to mount an extension link to the fourth hole of the the posts. brace mount with 2 bolts (1/2 x 2-3/4 inches), 2 Note: Use a level to make sure that the frame large washers, and 2 flange nuts (1/2 inch) as is level to the ground.
-
Page 7: Washer (13/16 X 1-1/2 Inches)
Installing the Sunshade Position the ROPS-mount bracket onto the top of the traction unit roll bar (Figure 15). Groundsmaster 3280 Machine Note: Make sure that the roll bar is centered in the ROPS-mount bracket. With the roll bar in the raised position, remove the hairpin cotters and the 2 pins (Figure 13). - Page 8 brace mount with 2 bolts (1/2 x 2-3/4 inches), and 2 flange nuts (1/2 inch) as shown in Figure g245151 Figure 18 1. Flange-head bolt (5/16 x 3. Grommet 1-1/4 inches) 2. Small washer 4. Clip nut g267174 Figure 17 Loosely mount each corner of the sunshade to 1.
- Page 9 Installing the Sunshade In the holes where the pins were removed, install the bolts and washers (Figure 20). Install another washer onto each bolt and Groundsmaster 360 or 7200 secure with nuts (3/4 inch) as shown in Figure Machines 20. Torque the nuts 323 to 396 N∙m (238 to 292 ft-lb).
- Page 10 Move the brace brackets up or down on the vertical roll bar posts until the sunshade frame is level to the floor. Use a level to make sure that the frame is level to the ground. Then, tighten the U-bolt flange nuts, securing the brace brackets to the posts.
- Page 11 Installing the Sunshade Groundsmaster 3500, 3505, 4000, and 4100 Machines or Reelmaster 3100, 3555, and 3575 Machines When you install the Universal Sunshade on a Reelmaster 3100 traction unit or a Groundsmaster 3500/3505 traction unit, install the Wheel Weight Kit. For Reelmaster 3555 and 3575 traction units, skip to step 10.
-
Page 12: Rops-Mount Bracket
Position the ROPS-mount bracket onto the On each side of the sunshade frame, loosely top of the traction unit roll bar (Figure 27). mount a brace to the brace bracket as follows: Make sure that the roll bar is centered in the •... -
Page 13: Brace
g267178 Figure 30 g245151 Figure 31 Models 30446, 30446N, 30447, and 30447N 1. Flange-head bolt (5/16 x 3. Grommet 1. Flange nut (1/2 inch) 5. Bolt (1/2 x 2-1/2 inches) 1-1/4 inches) 2. Mount hole 6. Brace 2. Small washer 4. -
Page 14: U-Bolt (4-7/8 X 2-3/4 Inches)
Insert a washer (13/16 x 1-1/2 inches) onto each Using the mounting holes shown in Figure bolt (3/4 x 4 inches) as shown in Figure loosely secure each of the brace brackets to the roll bar posts with a U-bolt (3-7/8 x 5 inches) and In the holes where the pins were removed, 2 flange nuts. -
Page 15: Sunshade
Installing the Sunshade Loosely install a brace bracket to each brace with a bolt (1/2 x 2-1/2 inches), washer (1/2 inch), and flange nut (1/2 inch) as shown in Reelmaster 5010 Machine or Figure Groundsmaster 4300 Machine Move the brace brackets up or down, on the vertical roll bar posts, until the sunshade frame Position the ROPS-mount brackets onto the is level to the floor. - Page 16 On each side of the sunshade frame, loosely mount a brace to the rear hole of the brace mount with a bolt (1/2 x 2-3/4 inches), 2 washers (1/2 inch), and a flange nut (1/2 inch) as shown Figure g245151 Figure 41 1.
- Page 17 Installing the Sunshade On each side of the sunshade frame, loosely mount an extension link to the fourth hole of the brace mount with 2 bolts (1/2 x 2-3/4 inches), Multi Pro 1750 Machine and 2 flange nuts (1/2 inch) as shown in Figure Position the ROPS-mount bracket onto the top of the turf sprayer roll bar...
- Page 18 Operation Transporting the Machine When transporting the machine, use the 2 holes in the front of the sunshade frame (under the sunshade) to tie down the sunshade to a secure location on the machine and prevent it from raising up in the wind (Figure 46).
- Page 19 Notes:...
- Page 20 The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.