Table of Contents
Advertisement
Quick Links
Quick Attach Front Frame
Groundsmaster
Model No. 30509—Serial No. 402800001 and Up
Important:
The Groundsmaster 360 must be equipped with the Electrical Accessory Kit, Part 115-0019,
to operate the Quick Attach Front Frame Kit.
This product complies with all relevant European directives. For details, please see the Declaration of
Incorporation (DOI) at the back of this publication.
Safety
Safety and Instructional
Decals
Safety decals and instructions are easily visible to the operator and are located near any area
of potential danger. Replace any decal that is damaged or missing.
© 2018—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
360 Multi-Purpose Machine
133-8061
Register at www.Toro.com.
decal133-8061
Form No. 3425-196 Rev A
Installation Instructions
Original Instructions (EN)
All Rights Reserved *3425-196* A
Printed in the USA
Advertisement
Table of Contents
Related Manuals for Toro 30509
Summary of Contents for Toro 30509
- Page 1 Quick Attach Front Frame Groundsmaster ® 360 Multi-Purpose Machine Model No. 30509—Serial No. 402800001 and Up Installation Instructions Important: The Groundsmaster 360 must be equipped with the Electrical Accessory Kit, Part 115-0019, to operate the Quick Attach Front Frame Kit.
-
Page 2: Installation
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. – No parts required Remove the cutting deck. Front attachment frame Mount the hydraulic tubes to the front Hydraulic tube, shorter attachment frame. Hydraulic tube, longer Screw (1/2 x 1-1/4 inches) Flange nut (1/2 inch) - Page 3 Note the location of the height-of-cut pin in the height-of-cut bracket for re-assembly purposes (Figure 2). Remove the height-of-cut pin from the height-of-cut bracket. Removing the Cutting Deck No Parts Required Procedure Park machine on a level surface with the cutting deck in the fully raised position.
- Page 4 Disconnect the end yoke of the PTO shaft from cutting deck gearbox shaft as follows. • Remove the roll pin from the end yoke and the gearbox shaft (Figure 3). Retain the roll Mounting the Hydraulic pin for re-use. Tubes to the Front Attachment Frame Parts needed for this procedure: Front attachment frame...
- Page 5 Position the front attachment frame under the front of the machine (Figure Raise the front attachment frame while aligning the mounting holes with the mounting holes in Mounting the Front the frame channels and the front frame cross plate (Figure Attachment Frame Parts needed for this procedure: Screw (1/2 x 1-1/4 inches)
- Page 6 Secure the top link assembly to the axle support with a screw (1/2 x 3-1/4 inches), 2 support washers, spacer, and a locknut (1/2 inch) as shown in Figure 5 Figure Installing the Hydraulic Note: The washers are to be positioned on the outside of the ears on the axle support.
-
Page 7: Mounting The Driveshaft
Connect the rear end of the shorter hydraulic tube to the tube on the machine (Figure Mounting the Driveshaft No Parts Required Procedure While aligning the driveshaft mounting holes with the jack shaft hole, slide the driveshaft onto the attachment jack shaft (Figure 10). -
Page 8: Installing The Switches
Installing the Switches Testing the Quick Attach Front Frame Parts needed for this procedure: Switch No Parts Required Decal Procedure Procedure Test the machine to ensure that all controls and parts are working as expected. Use a knife to cut out the provided decal. Start the engine. -
Page 9: Operation
Operating the Front Operation Attachment Note: Determine the left and right sides of the machine from the normal operating position. To operate the front attachment, use the rocker switches as indicated in Figure Think Safety First Please read all safety instructions and symbols in the safety section. - Page 10 To use the mower: Front Attach to Mower Deck Clean and grease all front attachments. Conversion Remove the driveshaft. Removing the deck Install the front deck. On a flat level surface raise deck to highest position. Attachments Place 2 furniture dollies under each end of the deck and lower it so it rests on the dollies.
-
Page 11: Recommended Maintenance Schedule(S)
Maintenance Recommended Maintenance Schedule(s) Maintenance Service Maintenance Procedure Interval • Torque the frame mounting bolts. After the first 10 hours • Torque wheel lug nuts. • Lubricate grease fittings Every 50 hours • Torque wheel lug nuts. Every 200 hours CAUTION If you leave the key in the ignition switch, someone could accidently start the engine and seriously injure you or other bystanders. -
Page 12: Electrical System Maintenance
Electrical System Storage Maintenance Machine • Disconnect the battery before repairing the machine. Disconnect the negative terminal first Thoroughly clean the machine and cab, paying and the positive last. Connect the positive terminal special attention to the following areas: first and the negative last. •... - Page 13 Notes:...
- Page 14 The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.
- Page 15 The Toro Company (“Toro”) respects your privacy. When you purchase our products, we may collect certain personal information about you, either directly from you or through your local Toro company or dealer. Toro uses this information to fulfil contractual obligations - such as to register your warranty, process your warranty claim or to contact you in the event of a product recall - and for legitimate business purposes - such as to gauge customer satisfaction, improve our products or provide you with product information which may be of interest.
- Page 16 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact the Toro importer.