Page 1 MAGNIA Z300 ™ User’s Guide...
Page 2: Fcc Notice
PS/2 mouse port, and monitor port. Changes or modifications made to this equipment not expressly approved by Toshiba, or parties authorized by Toshiba, could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: This device may not cause harmful interference in a commercial area.
Page 3: Warning Label
Warning Label Some warning labels are attached to units of this equipment, as shown below. Read these labels carefully for safe use of this equipment: power supply unit (System Unit) power supply unit (External Unit)
Page 5 Copyright This guide is copyrighted by Toshiba Corporation with all rights reserved. Under the copyright laws, this guide cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, however, with respect to the use of the information contained herein.
Page 6 OF THE FOREGOING. TOSHIBA ASSUMES NO LIABILITY FOR ANY DAMAGES INCURRED DIRECTLY OR INDIRECTLY FROM ANY TECHNICAL OR TYPOGRAPHICAL ERRORS OR OMISSIONS CONTAINED HEREIN. IN NO EVENT SHALL TOSHIBA BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, SPECIAL, OR EXEM- PLARY DAMAGES, WHETHER BASED ON TORT, CONTRACT, OR...
Page 7 Ytterligare information: This product is carrying the CE-Mark in accordance with the related European Directives. Respon- sible for CE-Marking is Toshiba Europe GmbH, Hammfelddamm 8, 41460 Neuss, Germany. Notice to user of EN55022 WARNING: This is a Class A product. In a domestic envi-...
Page 9 Introduction Key features of the MAGNIA Z300 Compact chassis of 2U 1/2 widths Installation flexibility (Rack and Micro Tower) Up to two Pentium III processors (866 MHz, 1 GHz) One 64bit/66MHz PCI slot Main memory expandable to a maximum of 3 GB...
Page 10: About This Guide
MAGNIA Z300 in a home environment. About this guide This guide introduces the features of the MAGNIA Z300 and explains how to set up, configure, and maintain the server. Before using the MAGNIA Z300 server, please read through the guide to gain an overall understanding of operating procedures and safety precautions .
Page 11: Safety Cautions
Safety cautions Before attempting to use your Toshiba MAGNIA Series Server, all safety instructions must be read carefully and fully understood. This manual contains the safety instructions that must be observed in order to avoid potential hazards that could result in personal injuries or damage to the rack or the units installed in them.
Page 12 ROM) contains Harness Eye/web settings and operation meth- ods. Harness Eye/web runs on Windows NT 4.0, Windows The Toshiba Server Setup Tool User’s Guide (on the Docu- mentation CD-ROM) contains instructions for setting up and optimizing installation of Microsoft ®...
Page 13: Service Options
Read Me First Addendum. Software License Agreement Service options Toshiba offers a full line of service options built around its war- ranty programs. See the warranty and service material included with the server for registration information. Maintenance contracts Periodic maintenance and inspection is essential for keeping the server fully operational and assuring its safe use.
Page 15: Table Of Contents
Contents Chapter 1: Getting Started... 2 Checking the items included with the server... 2 Mounting optional internal devices... 4 Environmental considerations... 5 Micro Tower Type/Rack Type... 5 Micro Tower Type... 7 Rack Type... 8 Power requirements... 9 Front view (with the front panel closed)... 10 Key lock...
Page 16 Rear view... 22 (1) AC connector ...22 (2) Security Loop ...22 I/O connectors... 23 Expansion slot... 24 LAN status indicators... 24 Inside the server... 25 (1) Motherboard... 25 (2) SCSI riser card... 25 (3) Cooling fans... 26 (4) CPU sockets... 26 (5) Memory slots...
Page 17 Setup of system configuration... 39 BIOS setup utility... 39 SCSI utility... 39 IDE RAID Setup utility... 39 Setup of disk array (RAID)... 40 Installing software... 41 Switching off the server... 42 Normal shutdown... 42 Using the automatic shutdown function... 42 Notes on using of the automatic shutdown function...
Page 18 xviii Chapter 3: External Unit Setup... 110 Types of External Unit... 110 Front view of the External Hard Drive Unit Z1 (with the front panel closed)... 111 Key lock... 111 Front view of the External Hard Drive Unit Z1 (with the front panel opened)...
Page 19 SCSI ID... 130 How to Connect an External Unit... 135 Chapter 4: System Configuration Setup... 138 BIOS setup utility... 138 Starting the setup utility... 139 Menu screen... 140 Changing BIOS Settings... 141 BIOS Settings... 141 SCSI Utility... 150 Starting the SCSI Utility... 151 Menu configuration...
Page 20 Installing the network driver... 176 Procedure after installation of the Windows 2000 Server... 177 NetWare... 178 Before installing the NetWare... 178 For installing NetWare 5.1 manually... 180 For installing the NetWare 4.2 manually... 186 Procedure after installation of the NetWare... 190 HarnessEye/web...
Page 21 The power button does not function after abortion... 211 The internal clock does not keep precise time... 211 Trouble with Application Software... 211 Remedy When Windows NT/2000 is Usable... 212 Remedy When Windows NT/2000 is Unusable... 213 Appendix A: Specifications... 216 System Unit...
Page 22 xxii...
Page 23 Chapter Checking the items included with the server ... 2 Mounting optional internal devices ... 4 Environmental considerations ... 5 Power requirements ... 9 Front view (with the front panel closed) ... 10 Front view (with the front panel opened) ... 11 Rear view ...
Page 24: Chapter 1: Getting Started
Checking the items included with the server Check the items in the package according to the accompanying Read Me First Addendum. If any of the items is missing or damaged, please contact your Toshiba dealer as soon as possible.
Page 25 Getting Started Checking the items included with the server NOTE: The Read Me First Addendum provides a listing of all standard accessories and their respective quantities. If you purchased the server together with an optional internal device, the optional device will also be incorporated with the standard accessories listed.
Page 26: Mounting Optional Internal Devices
Getting Started Mounting optional internal devices Mounting optional internal devices If you have purchased an optional internal device together with the server, install it before setting up the server. See “Installing/removing an optional device” on page 52. If you find it difficult to install an optional device yourself, always ask an authorized MAGNIA service provider to do it for you.
Page 27: Environmental Considerations
Environmental considerations Micro Tower Type/Rack Type Install the server in a clean, dust-free and well-ventilated place. Install the server on a level and steady surface. Never install the server upside down. Ensure the following when installing the server: - Do not expose to direct sunlight - Do not install in locations susceptible to vibration or shock.
Page 28 Getting Started Environmental considerations Only operate the server under the following conditions: - Ambient temperature: 50 to 95°F (10 to 35°C) (Micro Tower Type) 50 to 89°F (10 to 32°C) (Rack Type) - Ambient humidity: 30 to 80%Rh (No condensation) NOTE: To avoid condensation when the room temperature is too high or too low, do not start your server for about one hour after the room temperature has fallen within a range of 50 to...
Page 29: Micro Tower Type
Micro Tower Type Leave enough space around the server for maintenance and ventilation. 12 inches (30cm) or more Minimum clearances required for horizontal installation 12 inches (30cm) or more Minimum clearances required for vertical installation Getting Started Environmental considerations 8 inches (20cm) or more 8 inches (20cm) or more...
Page 30: Rack Type
Up to four System Units and External Units can be installed when stacked horizontally. Rack Type Use the optional Toshiba rack and rack mount kit to install a Rack Type. Leave a clearance of more than 24 inches (60 cm) before and behind the rack to ensure good ventilation around the server.
Page 31: Power Requirements
The use of an improper power cable may result in a fire. Do not use any optional part other than a genuine Toshiba parts or those parts recommended by Toshiba. The use of parts other than those recommended by Toshiba may result in a fire.
Page 32: Front View (With The Front Panel Closed)
Getting Started Front view (with the front panel closed) Front view (with the front panel closed) CD-ROM drive Front view with the front panel closed Key lock The front panel can be locked in two ways: full access and no access, depending on the direction of the keyhole.
Page 33: Front View (With The Front Panel Opened)
Front view (with the front panel opened) (2) CD-ROM drive (9) Device (10) HDD/LAN status indicators (1) Front panel Front view of the Micro Tower Type (1) Front panel The front panel can be opened by releasing the key lock, and push- ing its upper center (::) and detached by unhooking its hinges.
Page 34: Operation Buttons
Getting Started Front view (with the front panel opened) Removing the front panel (2) Operation buttons The server has 4 operation buttons on the front panel. Operation buttons Power/sleep button ( Reset button ( NMI button ( Display change button (...
Page 35 Front view (with the front panel opened) Power/ Press this button to turn on or off the server. sleep ON ... Pressing the button once causes the server button to start up. OFF ... Enabling the auto-shutdown function: If you hold your finger continuously for four sec- onds or more and take your finger away, the OS is shut down and the power supply is turned off.
Page 36: System Status Indicators
Getting Started Front view (with the front panel opened) (3) System status indicators Your server has 4 operating status indicators on the front panel. System status indicators Indicator Status Power Out of operation (AC power not supplied) Lit amber Out of operation (AC power supplied) Lit green In operation Disk Out of operation...
Page 37 Indicator Status Auto Out of operation Shut- Lit green Auto Shutdown function is enabled down Auto Shutdown function is ready to start when power switch is turned off Lit amber Auto Shutdown function is out of order - Auto Shutdown is used on Windows NT, Windows 2000 or Linux, and the Auto Shutdown function is not installed - Auto Shutdown is used on Windows NT, Windows...
Page 38: Front Panel Display
Drive Unit Z1, number of External Device Bay Unit Z1) is dis- played (scroll display). Example MAGNIA Z300 TOSHIBA Compact Server Pentium III xm, ExDisk xn, ExBay xi PentiumIII xm : m=number of CPUs ExDisk xn : n=number of External Hard Drive Unit Z1s ExBay xi : i=number of External Device Bay Unit Z1s The number of unit is reflected after power is on.
Page 39 Front view (with the front panel opened) Two messages can be set by Remote Management and Front Panel Display Setup Tool in the case of a Netware environ- ment. See “System Configuration Setup” on page 138. or the “Harness Eye/web User’s Guide” (on the Documentation CD- ROM) 3.
Page 40: Card Slot
Getting Started Front view (with the front panel opened) At shutdown by auto SD Now shutting down system. Holding down the display change button for at least four sec- onds displays the user message or system configuration. (5) Card slot The card slot accepts an optional wireless LAN card.
Page 41: Hdd/Lan Status Indicators
(9) HDD/LAN status indicators When the device bay accomodates hard disk drives, the status of each hard disk drive is indicated by the HDD status indicators placed below the device bay. The network status of the LAN1 and LAN2 connectors are dis- played on the LAN status indicators.
Page 42 Getting Started Front view (with the front panel opened) Indicator LNK 2 (LAN2) STS 1 (HDD1) Lit green Data is being read or written. amber Flashing amber PWR 1 (HDD1) Lit green Power is supplied to the hard disk drive. STS 2 (HDD2) Lit green Data is being read or written.
Page 43 Getting Started Front view (with the front panel opened) NOTE: When a STS indicator is lit amber, the corresponding hard disk drive may be faulty. If it is found to be defective, replace it. If your system is configured in redundancy (RAID1), you can replace the faulty drive without interrupting the system operation.
Page 44: Rear View
Getting Started Rear view Rear view (1) AC connector Rear view of the server (1) AC connector Used to connect the AC power cable. See “Connecting the power cable” on page 31. (2) Security Loop It is possible to attach chains, etc. to prevent the server from theft. Security Loop Security Loop...
Page 45: I/O Connectors
I/O connectors Plug the cables of peripheral devices into their respective I/O ports. (1) Mouse connector ( (2) Keyboard connector ( I/O connectors (1) Mouse connector ( ) Used to connect the PS/2 mouse. (2) Keyboard connector ( Used to connect the PS/2 keyboard. (3) LAN 1 connector ( Used to connect a 100BASE-T or 10BASE-T .
Page 46: Expansion Slot
Getting Started Rear view Expansion slot The server has 1 expansion slot for expansion cards: 64 bit/66 MHz PCI slot. LAN status indicators Activity Indicator Link Activity Link Status Lit green Connected successfully Network cable not connected or incor- rectly connected Lit green Data being transferred No active...
Page 47: Inside The Server
Inside the server (7) IDE HDD Cage (2) SCSI riser card (8) Board for wireless card Inside the server (1) Motherboard The main board can contain 2 CPU modules and 3 memory mod- ules at the maximum. (2) SCSI riser card The SCSI riser card has 1 PCI expansion slot (half length cards only).
Page 48: Cooling Fans
Getting Started Connecting peripheral devices (3) Cooling fans The server contains two cooling fans. (4) CPU sockets Used to mount CPU modules. See “CPU module” on page 78. (5) Memory slots Used to mount up to 3 memory modules to expand the server’s RAM (Random Access Memory).
Page 49 Connecting peripheral devices Connect peripheral devices to the server, according to the follow- ing procedure: NOTE: USB devices can be connected while the server is running. 1 Make sure that all the power buttons of the server and external units are turned off. 2 If the power cables of the server and external units are con- nected to an AC outlet, pull the plug of the power cable out of the AC outlet.
Page 50 AC outlets. WARNING: When connecting optional units, be sure to use genuine Toshiba parts or those recommended by Toshiba. If something other is connected to the server, it may cause an outbreak of fire.
Page 51: Floppy Disk Drive
NOTE: When connecting and disconnecting an interface cable, be sure to hold the cable connector. Some articles and interface cables of other brands cannot be connected to this server as external units and connecting cables. Before purchasing a peripheral unit, ask the manufac- turer or sales office of the article about its compatibility to this server.
Page 52: Maintenance
Getting Started Maintenance Maintenance Maintenance of the server If the outside of the server is dirty or stained, gently wipe it off with a soft cloth. If it is severely dirty, moisten the soft cloth with water and lightly wipe off the dirt.. If benzene, thinner or a similar substances is used for cleaning or a chemical such as an insecticide is applied onto the surface, the server may be deformed or discolored.
Page 53: Connecting The Power Cable
Connecting the power cable NOTE: Use of an uninterruptible power supply (UPS) is rec- ommended to avoid losing data because of unexpected shut- down or power failure. After connection of peripheral devices is complete, connect the power cable to this server following the procedure mentioned below.
Page 54 Getting Started Connecting the power cable WARNING: Be sure to use the power cable supplied with the server. Using another power cable may cause an outbreak of fire. Plug the power cable into an AC outlet with a ground line. If the power cable is plugged into an unspecified AC outlet, it may cause an outbreak of fire or electric shock.
Page 55: Switching On The Server
Switching on the server NOTE: When turning on the server again, turn on the power button at least 10 seconds after the power button was last turned off. If the server is switched on again within 10 sec- onds after it was switched off last, it may cause malfunction of the server or trouble with it.
Page 56: Turning On The Server By The "Remote Management" Function
This server has the function that the server can be started up by a client who is in connection with the network interface. Installing HarnessEye/web contained in the Toshiba Server Setup Tool on the client enables packets to be sent from the client to start up the server.
Page 57: Starting Up The System
Starting up the system The “Toshiba Server Setup Tool” is to be used for almost all of setup procedures for this system, such as installing the operating system (OS), making backup floppy disks etc. The “Toshiba Server Setup Tool” is comprised of the “Toshiba Server Setup Tool CD-ROM”...
Page 58: Starting Up By The Hard Disk Drive Unit (In The Case The Os Has Been Installed)
Getting Started Starting up the system Starting up by the hard disk drive unit (in the case the OS has been installed) To start up the server from the hard disk drive unit, proceed as follows: 1 Make sure that neither the floppy disk nor CD-ROM that is capable of starting up the server is in either drive unit.
Page 59: Starting Up By The Cd-Rom
Starting up by the CD-ROM To start up the server from the CD-ROM, proceed as follows: 1 Make sure that no floppy disk is placed in the floppy disk drive. 2 Switch on the power/sleep button. 3 Immediately after switching on the power/sleep button, press the eject button of the CD-ROM drive unit and place the start up CD-ROM in the drive.
Page 60: Making A Floppy Disk
How to make a backup floppy disk To make a system backup floppy disk using the “Toshiba Server Setup Tool,” proceed as follows (refer also to the on-screen instructions): 1 Place both the “Toshiba Server Setup Tool CD-ROM” and the “Startup Disk floppy disk”...
Page 61: Setup Of System Configuration
Setup of system configuration If the system is used as it was configured at the factory, it was properly set up before shipment. However, if something optional is added to the system after shipment, or it is desired to change the operating condition properly for use, it is required to set up the sys- tem once again.
Page 62: Setup Of Disk Array (Raid)
RAID is configured by minimum setting in this case. When “Detailed setup” or “No setup” is selected, or the RAID is to be configured without use of the Toshiba Server Setup Tool, it is required to set up the RAID.
Page 63: Installing Software
(Integrated server management tool) supplied with the server and the RAID controller software. See “User’s Manual for the Operating System” and “Toshiba Server Setup Tool User’s Guide” (on the Documentation CD- ROM).
Page 64: Switching Off The Server
Getting Started Switching off the server Switching off the server The method for switching off the server varies depending on the operating system used. Check the operating system and switch the server off using the normal method or use the automatic shutdown function.
Page 65 Switch the server off using the automatic shutdown function according to the following procedure: 1 Execute the specified shut down process for the application software running on the operating system.Be sure to save the data used on the application software before quitting. NOTE: As the server is switched off by the automatic shut- down function or ACPI function, the application software cur- rently in use is closed and unsaved data is deleted.
Page 66: Notes On Using Of The Automatic Shutdown Function
Getting Started Switching off the server Notes on using of the automatic shutdown function Hints on operation of the power/sleep button If the power/sleep button is used during the operation of the oper- ating system, during the shutdown operation or if the power/sleep button is operated in a wrong way, it may cause malfunction of the server.
Page 67 Logon by a user without shutdown rights If an unauthorized user logs on, the automatic shutdown function with the power/sleep button is disabled. If the server enters into this mode, log on to the server as the sys- tem administrator and then carry out the normal manual shutdown operation and switch off the power.
Page 68: Abnormal System Shutdown
Getting Started Switching off the server Abnormal system shutdown If the server is not shutdown using the normal method, the system can be forcibly stopped. However, this operation deletes unsaved data. To shut down the system forcibly, press the reset button. NOTE: If the server was forcibly shutdown, unplug the power cable from the AC outlet once and plug it in again.
Page 69 Chapter Before starting operation ... 48 Removing and replacing the server panels ... 54 Power Supply Unit ... 69 Memory module ... 72 CPU module ... 78 Internal battery ... 94 Hard Disk Drive (HDD) –IDE HDD– ... 98 Expansion cards ... 103...
Page 70: Chapter 2: Installing And Removing Hardware
Installing and Removing Hardware This chapter explains the different methods used to install and remove optional devices. Before starting operation Install optional devices before setting up the server.
Page 71: Before Starting Operation
Before starting operation Before starting operation WARNING: When installing an optional device, be sure to use genuine Toshiba parts or those recommended by Toshiba. If any other device is used, it may result in a fire hazard. For more information about optional devices, consult an authorized MAGNIA service provider.
Page 72 Installing and Removing Hardware Before starting operation The installation or removal of an optional device should be carried out at ambient temperatures of 50 to 95°F (10 to 35°C) for Micro Tower Types, or 50 to 89°F (10 to 32°C) for Rack Types, and at ambient humidity of 30 to 80%.
Page 73 Installing and Removing Hardware Before starting operation When connecting a cable to the server, pay careful attention to the shape of the connector. If a incorrect connector is forc- ibly connected, it may bend or damage the connector pins. If the cable connector has thumb screws for fastening, tighten them to secure the connection.
Page 74: Installing/Removing An Optional Device
Installing and Removing Hardware Before starting operation Installing/removing an optional device WARNING: When installing a peripheral unit, don't open any part other than those specified by the instructions. If an irrelevant part is opened, it may cause an electric shock. Install or remove an optional device following the procedure men- tioned below: 1 Carefully read the precautions mentioned in this chapter...
Page 75 Installing and Removing Hardware 8 Attach the server panels and outer covers to the server. In case of the Rack Type, fit the panels to the server before mounting it on the rack. 9 Connect the peripheral units and switch them on. 10 Plug the server's power cable connector into an AC outlet (or UPS) and then switch on the server.
Page 76: Removing And Replacing The Server Panels
Installing and Removing Hardware Removing and replacing the server panels Removing and replacing the server panels To mount optional devices inside the server, you need to remove the top panel depending on the option you are mounting. CAUTION: When sliding a server panel, be careful not to catch you finger between it and the server.
Page 77: Replacing The Top Panels (For Micro Tower Types)
Removing and replacing the server panels 4 Remove the front panel. See “Front panel” on page 11 5 Remove nine screws and the top panel. Removing the top panel Replacing the top panels (for Micro Tower Types) Follow these steps to replace the top panel: 1 Replace the top panel to the server carefully so that it does not catch any cable.
Page 78: When Using A Rack Type
Installing and Removing Hardware Removing and replacing the server panels When using a Rack Type Rack assembly procedure Quantity check Rack Mount Tray Parts provided with the System Unit or External Unit Name Base Assy Rail R Support Bracket(L) Support Bracket(R) Rail F WD(L) Rail F WD(R) PIN CATCH TRAY...
Page 79 Installing and Removing Hardware Removing and replacing the server panels Parts provided with the rack blank module BLANK BRACKET FRONT BRACKET FLAT SCREW(GRIP) 1 Decide on where to assemble the server. Installation position Screw (M6) temporary fastening positions Decide on where to assemble the server...
Page 80 Installing and Removing Hardware Removing and replacing the server panels 2 Temporarily fasten Rail R to the posts on the left and right of the rack rear, and Rail F (L) and Rail F (R) to the posts on the left and right at the front with Screws (M6).
Page 81 Installing and Removing Hardware Removing and replacing the server panels 4 Attach Pin Catch Tray to Rail F (L) and Rail F (R) with two Screws (M5). Pin Catch Tray Attach Pin Catch Tray 5 Attach Washer, Spring Washer and Guide Pin (M6) at two locations to the Base assembly.
Page 82 Installing and Removing Hardware Removing and replacing the server panels 6 Insert the Base Assembly into the Rail, and insert Guide Pin (M6) into the Pin Catch Tray. Insert the Base Assembly 7 Attach the Support Bracket (L) and Support Bracket (R) on the Base Assembly and fix them with two screws (M5).
Page 83 Installing and Removing Hardware Removing and replacing the server panels 8 Fix the Base Assembly to the rack with the claw screws on the front. Claw screw Fix the Base Assembly 9 Tighten the eight screws temporarily fastened in step 2. Fix Rails...
Page 84 Installing and Removing Hardware Removing and replacing the server panels 10 Attach Washer, Spring Washer and Guide Pin (M6) on the back. Attaching the Guide Pin 11 Attach the Front Bracket (L) or Front Bracket (R) to the server bay with Screws (M3). Screws (M3) Front Bracket Attach the Front Bracket...
Page 85 Installing and Removing Hardware Removing and replacing the server panels 12 Place the server bay on the Base Assembly and insert. Insert the server bay 13 Loosen the claw screw to draw out the Base Assembly by about 100 mm. Claw screw Drawing out the Base Assembly When turning the claw screws, remove the front panel so that you...
Page 86 Installing and Removing Hardware Removing and replacing the server panels 14 Fix the Base Assembly to the server housing with a screw (M3). Screw (M3) Fixing the Server Housing When using the rack blank module, attach the Front Bracket to the Blank Bracket using the two flat screws, and place both on the Base Assembly and fix with two flat screws.
Page 87 Installing and Removing Hardware Removing and replacing the server panels 15 Insert the entire Base Assembly into the rack. Inserting Into Rack Blank Module 16 Fix the housing on the left and right with the claw screws of Front Bracket (L) and Front Bracket (R). Claw screw Fix the housing on the left and right When turning the claw screws, remove the front panel so that you...
Page 88 Installing and Removing Hardware Removing and replacing the server panels Sliding the server out of or into the rack When installing an optional device to a Rack Type server, follow the instructions mentioned. WARNING: Don't slide more than two Rack Mount Trays out of the rack at the same time.
Page 89 Installing and Removing Hardware Removing and replacing the server panels Sliding the server (Rack Type) out of the rack Slide the server out of the rack in the procedure described below, while referring to “Before starting operation” on page 48. 1 If the server is running, shut it down and switch off the power.
Page 90 Installing and Removing Hardware Removing and replacing the server panels Removing the screw 7 Slide the server out of the rack. Sliding the server (Rack Type) into the rack 1 Gently slide the server into the rack, according to the rack assembly procedure step 10 - 15.
Page 91: Power Supply Unit
Power Supply Unit Removing the power supply unit The power supply unit must be removed and attached when replacing or adding on memory or batteries. NOTE: The installation and replacement of the power supply unit requires special technology and knowledge. If you have no experience in installing the power supply unit or if you need assistance, consult your authorized MAGNIA service provider.
Page 92: Installing The Power Supply Unit
Installing and Removing Hardware Power Supply Unit 5 Disconnect the power cable and signal cable. Disconnecting the cables Installing the power supply unit NOTE: The installation and replacement of the power supply unit requires special technology and knowledge. If you have no experience in installing the power supply unit or if you need assistance, consult your authorized MAGNIA service provider.
Page 93 Installing and Removing Hardware Power Supply Unit 4 Connect the power cable and signal cable. Connecting the cables 5 Install the power supply unit, slide back slightly and fix it with six screws. Installing the power supply unit 6 Attach the server panels and outer covers.
Page 94: Memory Module
Installing and Removing Hardware Memory module Memory module Your server can accommodate a maximum of three 128-MB, 256- MB, 512-MB or 1-GB DIMMs (Dual In-line Memory Modules) with the ECC (Error Correction Control), which operate at a sys- tem bus clock frequency of 133 MHz. See “Specifications”...
Page 95 Installing and Removing Hardware Slot1 Slot2 1024 1024 Memory module Unit : MB Slot3 Total 1152 1152 1024 1024 1024...
Page 96: Installing An Additional Memory Module
Installing and Removing Hardware Memory module Memory slots WARNING: When installing a peripheral unit, don't open any part other than those specified by the instructions. Touching unspecified parts may cause an electric shock. CAUTION: Do not install or remove additional memory mod- ules when the server has just been switched off.
Page 97 Installing and Removing Hardware Before installing an additional memory module, carefully read “Before starting operation” on page 48 and proceed as follows: 1 If the server is in operation, first shut it down and switch off the power supply to it. 2 Unplug the power cable from the AC outlet.
Page 98 Installing and Removing Hardware Memory module 6 Insert the memory module into the proper memory slot, paying attention to the position of each notch on the memory module. Insert the memory module until it is locked by the hooks on both sides.
Page 99: Removing A Memory Module
Removing a memory module Before removing a memory module, carefully read “Before start- ing operation” on page 48 and proceed to the job following the procedure mentioned below: 1 If the server is in operation, shut it down and switch off the power.
Page 100: Cpu Module
Installing and Removing Hardware CPU module 6 Install the power supply unit. See “Power Supply Unit” on page 69 7 Fit the server panels and outer covers to the server. 8 Connect the power cable of the server to the power supply and switch on the server CPU module The server is classified into 2 models, each having different CPU...
Page 101: Installing The Cpu Module
Installing the CPU module NOTE: The CPU module may be fatally damaged by static electricity because it consists of precise electronic parts. The human body contains static electricity. Therefore, discharge the static electricity before installing the CPU module. Static electricity can be discharged by touching a nearby metallic object with your fingers.
Page 102 Installing and Removing Hardware CPU module Removing the PCI bracket...
Page 103 Installing and Removing Hardware 5 Remove one screw that fix the riser card and remove the riser card. Removing the riser card NOTE: Lift up the riser card with a screwdriver to remove. CPU module...
Page 104 Installing and Removing Hardware CPU module 6 Remove two screws and the fan duct. Removing the fan duct 7 Raise the lock lever of the expansion CPU socket. Raising the lock lever...
Page 105 Installing and Removing Hardware 8 Align the CPU pins correctly with the holes in the socket, and insert the CPU module as far as it will go. Inserting the CPU module NOTE: A standard CPU module is installed in the socket 1. To extend the CPU module, install it in the socket 2.
Page 106 Installing and Removing Hardware CPU module 11 Lightly push the heat sink in the direction of the socket, and fix it by engaging the clips with the upper and lower hooks of the socket. Attaching the heat sink Fixing the clips NOTE: Do not push the fin section of heat sink of the CPU module.
Page 107 Installing and Removing Hardware CPU module 12 Attach the fan duct and fix it with two screws. Attaching the fan duct 13 Attach the riser card and fix it with one screw. Attaching the riser card 14 Fix the PCI bracket with two screws.
Page 108 Installing and Removing Hardware CPU module Fixing the PCI bracket 15 Install the server panels. 16 Connect the power cable of the server to the power supply and switch on the server. 17 Confirm that the CPU module is recognized properly with the display on the screen.
Page 109: Replacing The Cpu Module
Replacing the CPU module NOTE: The CPU module may be fatally damaged by static electricity because it consists of precise electronic parts. The human body contains static electricity. Therefore, discharge the static electricity before installing the CPU module. Static electricity can be discharged by only touching a nearby metallic object with your fingers.
Page 110 Installing and Removing Hardware CPU module Removing the PCI bracket 5 Remove one screw that fix the riser card, and remove the riser card. Removing the riser card...
Page 111 Installing and Removing Hardware NOTE: Lift up the riser card with a screwdriver to remove. 6 Remove two screws and the fan duct. Removing the fan duct. 7 Release the clips that secure the heat sink for the CPU module to be removed, and remove the heat sink.
Page 112 Installing and Removing Hardware CPU module Releasing the clips Removing the heat sink 8 Raise the lock levers of the socket in which the CPU module you want to remove is mounted. Raising the lock lever...
Page 113 Installing and Removing Hardware 9 Remove the CPU module. Removing the CPU module 10 Install a new CPU module following the same procedure as for extension modules. NOTE: Do not push the fin section of heat sink of the CPU module.
Page 114 Installing and Removing Hardware CPU module 12 Install the riser card on the motherboard and fix it with one screw. Installing the PCI riser card 13 Attach the PCI bracket with two screws. Fixing the PCI bracket 14 Install the server panels. 15 Connect the power cable of the server to the power supply and switch on the server.
Page 115 Installing and Removing Hardware The example below shows a 866 MHz, 2-CPU configuration. Phoenix Server BIOS 4 Release 6.0 Copyright 1985-2000 Phoenix Technologies Ltd. All Rights Reserved BIOS-Version X.XX CPU=2 Pentium(R)III Processor 866MHz XXXK System RAM Passed XXXM Extended RAM Passed NOTE: When a CPU module is extended, the operating sys- tem (OS) may have to be reinstalled to recognize a new CPU module.
Page 116: Internal Battery
This server has an internal battery to store the information on a timer and system configuration. The replacement of a battery requires special technology and knowledge. Toshiba recommends that you ask your authorized MAGNIA service provider to replace the internal battery.
Page 117: Replacing The Internal Battery
Replacing the internal battery Replace the battery in the procedure described below, while refer- ring to “Before starting operation” on page 48: 1 Write down the system configuration information. 2 Shut down and switch off your server. 3 Unplug the power cable. NOTE: Don't replace the battery when your server is on, oth- erwise your server or the internal battery could be damaged.
Page 118 Installing and Removing Hardware Internal battery 7 Put your fingers below the battery, and pull it up. Removing the battery 8 Install a new battery with polarity (+) up. Installing the battery...
Page 119 Installing and Removing Hardware 9 Install the board for the wireless card and fix it with four screws. Installing the board for the wireless card 10 Install the power supply unit. 11 Install the server panels. 12 Connect the power cable of the server to the power supply, and switch on the server.
Page 120: Hard Disk Drive (Hdd) -Ide Hdd
Installing and Removing Hardware Hard Disk Drive (HDD) –IDE HDD– Hard Disk Drive (HDD) –IDE HDD– Slot numbers (of 1 to 2 from bottom) are assigned to each slot of a hard disk drive. Installing the hard disk drive NOTE: The installation and replacement of a hard disk drive requires special technology or knowledge.
Page 121 Installing and Removing Hardware Hard Disk Drive (HDD) –IDE HDD– 5 Pull out the HDD slot spacer that was partially extracted. 6 Push the hard disk drive completely into the slot where you want to mount it. Installing the hard disk drive 7 Close the detachable lever and fix it.
Page 122: Replacing A Hard Disk Drive During Operation
NOTE: The installation and replacement of a hard disk drive requires special technology and knowledge. Toshiba recom- mends that you ask your authorized MAGNIA service pro- vider to replace the hard disk drive.
Page 123 Installing and Removing Hardware Hard Disk Drive (HDD) –IDE HDD– 2 Confirm the position of a faulty device. The STS indicator of the faulty device is lit amber. CAUTION: The hard disk drive generates heat when in use. To avoid burns, hold the disk tray when removing the hard disk drive.
Page 124 Installing and Removing Hardware Hard Disk Drive (HDD) –IDE HDD– Pulling out the hard disk drive 5 Install a new hard disk drive in the same procedure as for extension. See “Installing the hard disk drive” on page 98. 6 After a short time, confirm that the PWR indicator lights up. 7 Attach the front panel.
Page 125: Expansion Cards
Expansion cards One PCI expansion card can be installed in the server. Expansion slots Restrictions on PCI expansion cards The PCI slot support 64 bit/66 MHz and less than 194mm long PCI cards. Installing and Removing Hardware Expansion cards PCI slot...
Page 126: Installing The Scsi Riser Card
Installing and Removing Hardware Expansion cards Installing the SCSI riser card WARNING: Do not touch any parts except those necessary for installing the device. There are many high-voltage parts that may cause an electric shock. When installing or removing the expansion card, shut the server down, switch off the power, and pull out the power plug from the wall outlet.
Page 127 Installing and Removing Hardware Expansion cards 5 Install the SCSI cable. Installing the SCSI cable 6 Connect the SCSI cable of the SCSI riser card. Connecting the SCSI cable of the SCSI riser card...
Page 128 Installing and Removing Hardware Expansion cards 7 Insert the expansion card in the SCSI riser card. Inserting the expansion card 8 Install the SCSI riser card on the motherboard and fix it by one screw. Installing the SCSI riser card...
Page 129 Installing and Removing Hardware Expansion cards 9 Fix the PCI bracket with two screws. Fixing the PCI bracket 10 Install the power supply unit. 11 Install the server panels. 12 Connect the power cable of the server to the power supply, switch on the server.
Page 130 Installing and Removing Hardware Expansion cards...
Page 131 Chapter Types of External Unit ... 110 Front view of the External Hard Drive Unit Z1 (with the front panel closed) ... 111 Front view of the External Hard Drive Unit Z1 (with the front panel opened) ... 112 Rear view of the External Hard Drive Unit Z1 ... 117 Installing and Removing Hard Disk Drive (HDD) -SCSI HDD- ...
Page 132: Chapter 3: External Unit Setup
External Unit Setup Types of External Unit The following two types of External Unit (sold separately) are available for this server: External Hard Drive Unit Z1 External Device Bay Unit Z1...
Page 133: Front View Of The External Hard Drive Unit Z1 (With The Front Panel Closed)
Front view of the External Hard Drive Unit Z1 (with the front panel closed) Front view of the External Hard Drive Unit Z1 (with the front panel closed) Front view with the front panel closed Key lock The front panel can be locked at two levels: full access and no access, depending on the direction of the keyhole.
Page 134: Front View Of The External Hard Drive Unit Z1 (With The Front Panel Opened)
External Unit Setup Front view of the External Hard Drive Unit Z1 (with the front panel opened) Front view of the External Hard Drive Unit Z1 (with the front panel opened) (3) System status indicator (2) Power switch HDD 2 HDD 1 Front view of the Micro Tower Type (1) Front panel...
Page 135: Power Button
Front view of the External Hard Drive Unit Z1 (with the front panel opened) (2) Power button The server has an power button on the front panel. Power button Power button Power button See “Switching on the server” on page 33 and “Switching off the server”...
Page 136: System Status Indicators
External Unit Setup Front view of the External Hard Drive Unit Z1 (with the front panel opened) (3) System status indicators This server has 2 operating status indicators on the front panel. System status indicators Indicator Power Disk/Fault NOTE: If any trouble has occurred, contact an authorized MAGNIA service provider.
Page 137: Hdd Status Indicators
Front view of the External Hard Drive Unit Z1 (with the front panel opened) (4) HDD status indicators If the device bay accommodates hard disk drives, the status of each hard disk drive is indicated by the power indicator and the status indicator located above the device bay.
Page 138 External Unit Setup Front view of the External Hard Drive Unit Z1 (with the front panel opened) NOTE: When a status indicator is lit amber, the correspond- ing hard disk drive may be faulty. If it is found to be defective, replace it.
Page 139: Rear View Of The External Hard Drive Unit Z1
Rear view of the External Hard Drive Unit Z1 AC power connector Rear view of the External Hard Drive Unit Z1 AC power connector Used to connect the AC power cable. See “Connecting the power cable” on page 31. I/O connectors Plug the cables of peripheral devices into their respective I/O ports.
Page 140: Installing And Removing Hard Disk Drive (Hdd) -Scsi Hdd
External Unit Setup Installing and Removing Hard Disk Drive (HDD) -SCSI HDD- Installing and Removing Hard Disk Drive (HDD) -SCSI HDD- The slot numbers (of 1 to 4) are assigned to each slot of a hard disk drive. Read “Before starting operation” on page 48 before installing additional hard disk drives, and mount them in the slots, starting from the bottom left.
Page 141 Installing and Removing Hard Disk Drive (HDD) -SCSI HDD- 2 Tilt over the detachable lever of the slot where you want to install a hard disk drive, by pulling its knob toward you. Pulling the detachable lever toward you 3 Pull out the HDD slot spacer that was partially extracted. 4 Push the hard disk drive completely into the slot where you want to mount it.
Page 142: Replacing A Hard Disk Drive During Operation
External Unit Setup Installing and Removing Hard Disk Drive (HDD) -SCSI HDD- 5 Close the detachable lever and fix it. Push in the detachable lever so that the hard disk drive is firmly fixed. Fixing the detachable lever 6 Attach the front panel. NOTE: The setting of an operating system (OS) or application software may have to be changed when the hard disk drive is extended.
Page 143 See “MegaRAID Software Guide.” The installation and replacement of a hard disk drive requires special technology and knowledge. Toshiba recommends that you ask your authorized MAGNIA service provider to replace the hard disk drive. Especially, pay careful attention when replacing the hard disk drive while the system is in operation.
Page 144 External Unit Setup Installing and Removing Hard Disk Drive (HDD) -SCSI HDD- Removing the front panel See “Front panel” on page 11. 2 Confirm the position of a faulty disk. The STATUS indicator ( CAUTION: The hard disk drive generates heat when in use. To avoid burns, hold the disk tray when removing the hard disk drive.
Page 145 Installing and Removing Hard Disk Drive (HDD) -SCSI HDD- NOTE: Before pulling out the hard disk drive, make sure that it is faulty. If a normally operating disk is pulled out by mis- take, it may damage the server or destroy and lose important programs or data.
Page 146: Setup Of Disk Array (Raid)
RAID is configured by minimum setting in this case. When “Detailed setup” or “No setup” is selected, or the RAID is to be configured without use of the Toshiba Server Setup Tool, it is required to set up the RAID.
Page 147: Front View Of The External Device Bay Unit Z1 (With The Front Panel Closed)
Front view of the External Device Bay Unit Z1 (with the front panel closed) Front view of the External Device Bay Unit Z1 (with the front panel closed) Front view with the front panel closed Key lock The front panel can be locked at two levels: full access and no access, depending on the direction of the keyhole.
Page 148: Front View Of The External Device Bay Unit Z1 (With The Front Panel Opened)
External Unit Setup Front view of the External Device Bay Unit Z1 (with the front panel opened) Front view of the External Device Bay Unit Z1 (with the front panel opened) (2) Power switch Front view of the Micro Tower Type (1) Front panel The front panel can be opened by releasing the key lock, pushing its upper center (::) and detached by unhooking its hinges.
Page 149: Power Button
Front view of the External Device Bay Unit Z1 (with the front panel opened) (2) Power button The server has an power button on the front panel. Power button Power button Power button See “Switching on the server” on page 33 and “Switching off the server”...
Page 150: System Status Indicators
External Unit Setup Front view of the External Device Bay Unit Z1 (with the front panel opened) (3) System status indicators This server has 2 operating status indicators on the front panel. System status indicators Indicator Power Fault NOTE: If any problem has occurred, contact an authorized MAGNIA service provider.
Page 151: Rear View Of The External Device Bay Unit Z1
Rear view of the External Device Bay Unit Z1 AC power connector Rear view of the External Device Bay Unit Z1 AC power connector Used to connect the AC power cable. See “Connecting the power cable” on page 31. I/O connectors Plug the cables of peripheral devices into their respective I/O ports.
Page 152: Scsi Connector ()
External Unit Setup Installing SCSI device (2) SCSI connector ( Used to connect the System Unit. See “How to connect peripheral devices” on page 26. Installing SCSI device The installation of a SCSI device requires special knowledge or technology. If you have no experience in installing a SCSI device or require assistance, consult your authorized MAGNIA service provider.
Page 153 External Unit Setup Installing SCSI device 3 Open the front panel. 4 Remove four screws and remove the outer cover (upper). Removing the outer cover 5 Remove seven screws and remove the top cover. Removing the top cover...
Page 154 External Unit Setup Installing SCSI device 6 Remove the power and signal cables. When removing the signal cable, disconnect it from the Exter- nal Device Bay Unit Z1. Removing the cables 7 Remove four screws that fix the SCSI device. Removing the screws...
Page 155 External Unit Setup Installing SCSI device 8 Pull out the SCSI device completely. Remove the SCSI device 9 Set the SCSI ID so that it would not be the same as other device. 10 Insert the SCSI device into the unit. 11 Attach the four screws and fix the SCSI device.
Page 156 External Unit Setup Installing SCSI device 12 Connect the power and signal cables. Connecting the cables 13 Attach the top cover and fix it with seven screws. Attaching the top cover...
Page 157: How To Connect An External Unit
External Unit Setup How to Connect an External Unit 14 Attach the outer cover (upper) and fix it with four screws. Attaching the outer cover 15 Close the front panel. 16 Connect the power cable of the server to the power supply and switch on the server.
Page 158 External Unit control connector (IN) Connecting the External Units External Hard Drive Unit Z1 PCI card (SCSI card) SCSI connector (IN) External Unit Control Cable External MAGNIA Z300 (System Unit) SCSI connector External Hard Drive Unit Z1 External Device Bay Unit Z1...
Page 159 Chapter BIOS setup utility ... 138 SCSI Utility ... 150 Remote Management and Front Panel Display Setup Tool 156 Configuring MegaRAID IDE ... 160...
Page 160: Chapter 4: System Configuration Setup
System Configuration Setup BIOS setup utility NOTE: The menus shown in this chapter are just examples. The BIOS Setup Utility is a menu type of program designed to verify and modify the basic settings of the motherboard.
Page 161: Starting The Setup Utility
Starting the setup utility The BIOS screen will appear when the server is started. Phoenix BIOS 4.0 Release X.X.X.XX Copyright 1985-2000 Phoenix Technologies Ltd., All Rights Reserved BIOS Version X.X VIA Apollo Pro133AX ( VT82C694X + VTA686B ) CPU = Pentium (R) III Processor XXX MHz XXXXXXXX System RAM Passed XXXXXXXX Extended RAM Passed 0256K Cache SRAM Passed...
Page 162: Menu Screen
System Configuration Setup BIOS setup utility Menu screen The following menu will be displayed when the BIOS Setup Util- ity is started: Main Advanced System Time: System Date: Primary Primary FSB Frequency DRAM Frequency Processor Settings Processor 1 Processor 2 Memory Shadow Memory Cache Summary screen...
Page 163: Changing Bios Settings
BIOS Setup Utility Keyboard Commands <F1> <Esc> <Enter> < > < > < >< > Specifies a menu. <F9> <F10> Changing BIOS Settings To change BIOS settings, follow these steps: 1 Move the black bar to the desired item using the arrow keys <...
Page 164: Main Menu
System Configuration Setup BIOS setup utility Main menu System Time: System Date: Primary Primary FSB Frequency DRAM Frequency Processor Settings Processor 1 Memory Shadow Memory Cache Summary screen AC ON state System Memory Extended Memory BIOS Version BMC Version System Time/System Date Enter the system date and time.
Page 165: Memory Cache
DRAM Frequency Displays DRAM Frequency. Processor Settings Processor 1/Processor 2 Displays Processor speed/ID/Cache memory size. Processor 2 is only displayed when there is a second CPU. Memory Shadow The following submenu appears: System shadow: Video shadow: System shadow Do not change this setting. Video shadow Shadow video BIOS and improves performance.
Page 166 System Configuration Setup BIOS setup utility Enables or disables all memory caching. Cache System BIOS area Controls caching of system BIOS area. Cache Video BIOS area Controls caching of video BIOS area. Cache Base 0-512k Controls caching of base memory 0-512k. Cache Base 512k-640k Controls caching of base memory 512k-640k.
Page 167: Advanced Menu
Displays available system memory size. Extended Memory Displays extended memory size. BMC Version Displays BMC version. BIOS Version Displays system BIOS version. Advanced menu This section describes the advanced settings available in the vari- ous BIOS Setup Utility menus. PCI Configuration Advanced Chipset Control I/O Device Configuration PS/2 Mouse...
Page 168 System Configuration Setup BIOS setup utility SCSI Set SCSI riser card setting. Set on-board LAN setting. PCI Device slot #1 The following submenu appears: PCI Device slot #1: Option ROM Scan: Enable Master: Latency Timer: Option ROM Scan Do not change this setting. Enable Master Enables selected device as a PCI bus master.
Page 169 The following submenu appears. Serial port A: Serial port A Do not change this setting. PS/2 Mouse Do not change this setting. Local Bus IDE adapter Set local IDE adapter setting. Legacy USB support When Disabled is set, the USB floppy disk drive can no longer be used.
Page 170: Security Menu
System Configuration Setup BIOS setup utility Security menu This section describes the security settings available in the BIOS Setup Utility. Supervisor Password is: User Password is: Set Supervisor Password Set User Password Diskette Access: Password on Boot: Set Supervisor Password Allows Supervisor Password to be registered, changed, and/or deleted.
Page 171: Boot Menu
Boot menu This section describes the Boot options available in the BIOS Setup Utility. This menu allows you to set the sequence in which the operating system searches devices for the boot files. Do not change these settings. +Removable Devices +Hard Drive CD-ROM Drive Intel(R)Boot Agent Version X.X.XX...
Page 172: Scsi Utility
System Configuration Setup SCSI Utility Exit menu Exit Saving Changes Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes Exit Saving Changes Saves changes and restarts the system. Performs the same function as pressing the F10 key. Exit Discarding Changes Discards all recent configuration changes, then restarts the server.
Page 173: Starting The Scsi Utility
Starting the SCSI Utility When the server is turned on or restarted, the monitor displays the onboard SCSI BIOS initialize message shown below. The display differs based on the type of SCSI device installed in the server. Adaptec AIC-7892 SCSI BIOS vX.XX (C)1998 Adaptec, Inc.
Page 174: Menu Configuration
System Configuration Setup SCSI Utility Menu configuration When the SCSI Utility starts, the monitor enters the following main menu display mode: Adaptec AIC-7892 < SCSISelect (TM) > Utility vX.XX Would you like to configure the host adapter, or run the SCSI disk Utilities? Select the operation and press <Enter>...
Page 175: Changing Scsi Device Settings
Changing SCSI Device Settings 1 Using the arrow keys (< >< >), select the desired item then press the <Enter> key. The submenu or selection menu corre- sponding to the selected item appears. 2 Make any necessary changes then save the changes. 3 Select Exit this Menu to exit the submenu.
Page 176 System Configuration Setup SCSI Utility Host Adapter SCSI Termination Specifies whether the SCSI bus is to be terminated using the SCSI host adapter. Do not change this setting. Boot Device Options Specifies the SCSI device from which the system is to be booted.
Page 177 Specifies whether logical unit numbers are supported. Include in BIOS Scan Specifies whether the device is to be scanned when SCSI BIOS starts. Advanced Configuration Options Sets up detailed data on the SCSI controller. Reset SCSI Bus at IC Initialization Specifies whether or not to reset the SCSI bus during the SCSI controller resetting process.
Page 178: Remote Management And Front Panel Display Setup Tool
When using Remote Management and Front Panel Display Setup Tool, create a floppy disk from the Toshiba Server Setup Tool. How to start up and operate the setup tool Insert the floppy disk created using Toshiba Server Setup Tool into the floppy disk drive, and start up the system.
Page 179 Remote Management and Front Panel Display Setup Tool [To set up the IP address] 1 When the menu appears, select [1] or [2]. The currently held information appears as follows, and the sys- tem waits for entry of the new update values. *** Setup LANx IP Address *** Current LANx IP Address = nnn.nnn.nnn.nnn Change LANx IP Address ? [y/n]...
Page 180 4 Press the <Esc> key. This restarts the system. To set up the front panel display 1 When the menu appears, select 2 TOSHIBA Front Panel Dis- play Setup Tool. >> nnn.nnn.nnn.nnn...
Page 181 Remote Management and Front Panel Display Setup Tool The following screen appears. TOSHIBA Front Panel Display Setup Tool version X.XX COPYRIGHT TOSHIBA CORPORATION 2001. ALL RIGHTS RESERVED. * Current message USER1 LINE1 > USER1 LINE2 > USER2 LINE1 > USER2 LINE2 >...
Page 182: Configuring Megaraid Ide
System Configuration Setup Configuring MegaRAID IDE Configuring MegaRAID IDE Configuring MegaRAID IDE This section explains how to: configure MegaRAID IDE and arrays assign RAID levels plan the array configuration optimize storage use the MegaRAID IDE Setup Utility Configuring Arrays Organize the physical disk drives in arrays after the drives are con- nected to MegaRAID IDE.
Page 183: Selecting A Raid Level
RAID Minimum Number of Level Selecting a RAID Level To ensure the best performance, you should select the optimal RAID level when you create a system drive. The optimal RAID level for your disk array depends on the following factors: Number of drives in the disk array Capacity of the drives in the array Need for data redundancy...
Page 184 System Configuration Setup Configuring MegaRAID IDE 1 Press the <Ctrl> + <M> keys to run the MegaRAID IDE Man- ager. 2 Define and configure one or more logical drives. 3 Create and configure one or more system drives (logical drives). Select the RAID level, write cache policy, virus protec- tion, and DMA transfers.
Page 185: Using The Megaraid Ide Setup Utility
Using the MegaRAID IDE Setup Utility Setup window The Setup window has three sections: array information physical drive information help information Only the Array Information window and Physical Drives Informa- tion window are active. The Array Information window is editable. The Physical Drives Information window is not editable. To access this screen, press the <Ctrl>...
Page 186 System Configuration Setup Configuring MegaRAID IDE Drive numbers of the physical drives included in the array Stripe size (32 KB to 4 MB) which is valid for Stripe configu- rations only Whether the system is bootable from one of the configured arrays Build Array function, which is valid for Mirror array.
Page 187: Switch Windows (Tab)
Boot sector virus protection DMA transfers Enable / Disable Buzzer NOTE: These options apply to all drives attached to Mega- RAID IDE. Help section The Help section of the Setup window screen displays hints on available options. The Help section also provides a list of keys that you can use to perform tasks, such as auto configuring, creating or deleting an array.
Page 188: Create Array (F4)
System Configuration Setup Configuring MegaRAID IDE Create Array (F4) Press the <F2> key to create a disk array. When you create an array, a default array template is created. You must edit the array properties to complete the array creation. Use arrow navigation keys to highlight a property field and press <Enter>...
Page 189: Stripe Size
Configuring MegaRAID IDE DRIVE SELECTION BOX ] Cntlr 0-Primary Master ] Cntlr 0-Secondary Master Use the arrow navigation keys and press the Spacebar to select or deselect the drive or drives to be part of the array. Press <Enter> when done. If you select mirror mode as the array type, you must select two drives to be in the array.
Page 190 System Configuration Setup Configuring MegaRAID IDE Bootable This determines which of the configured arrays should be used for booting the system when MegaRAID IDE is selected as the boot device. The options are Yes or No. BOOT OPTION You can select the boot device from the system BIOS setup. Only one array is allowed to be bootable in a system.
Page 191: Delete Array (F5)
Delete Array (F5) Press the <F5> key to delete a currently configured array. Use arrow keys to go over to the array you want to delete and then press <F5>. CAUTION: Use this option with caution. When you delete an array, you lose the array configuration and the data saved in the array.
Page 192: Save And Exit (F10)
System Configuration Setup Configuring MegaRAID IDE Save and Exit (F10) When you have completed the array configuration, press <F10> to save the configuration and exit. If you do not want to save the con- figuration or any changes that you have made, press the <Esc> key.
Page 193 Chapter Windows Windows NetWare ... 178 HarnessEye/web ... 191 AFT, ALB and IPSec functions ... 192 Auto-shutdown function ... 202 ® NT Server 4.0 ... 172 ® 2000 Server ... 173...
Page 194: Chapter 5: Installing Software
Windows NT You can install Windows NT on your server automatically using the Toshiba Server Setup Tool. See “Toshiba Server Setup Tool User's Guide“ for the procedure of the automatic installation. Setting the motherboard Before proceeding to the installation of Windows NT, start the BIOS Setup Utility on your system, and specify “WinNT2K”...
Page 195: Windows® 2000 Server
Setup Tool or installing it manually, by following the normal installation steps set for Windows 2000. This section explains how to install Windows 2000 manually. See the “Toshiba Server Setup Tool User's Guide” (on the Docu- mentation CD-ROM) for the procedure of the automatic installation.
Page 196: Selecting The Disk Driver
Installing Software Windows® 2000 Server Selecting the disk driver Selecting the IDE CD-ROM Controller driver Use the driver contained on the CD-ROM of the Windows 2000 Server. Selecting a driver for the IDE RAID controller To select the driver, follow these steps. 1 Press the <F6>...
Page 197 8 When the following message appears, select “Adaptec AIC- 7892 Ultra160 SCSI ”. Adaptec ACI-7892 Ultra160 SCSI Selecting a driver for the RAID controller E/F (MR493/MR475) To select the driver, follow these steps. 1 Press the <F6> key after the Windows 2000 Server Setup win- dow has turned entirely to blue.
Page 198: Installing The Display Driver
When installation of the Windows 2000 Server is complete, it is required to change the driver that is automatically detected by the Windows 2000 Server Installer to the display driver contained on the CD-ROM of the Toshiba Server Setup Tool. To change the display driver, follow the procedure mentioned below:...
Page 199: Procedure After Installation Of The Windows 2000 Server
3 Click “Next” in the “Update Device Driver Wizard”. 4 Select “Search for a suitable driver for my device” , click Next 5 Set Server Setup Tool CD into CD-ROM drive, check at “Specify a location”, click “Next”. 6 Type following driver pass to “Copy manufacture's files from:”, then click “Next”...
Page 200: Netware
On the other hand, an MS-DOS disk can be created by use of the Toshiba Server Setup Tool so that the MS-DOS environment can be set up manually without use of the DOS Installer of the Toshiba Server Setup Tool.
Page 201 Setup of the MS-DOS environment Installation of NetWare can be done in the three ways : (1) Install the MS-DOS by use of the Toshiba Server Setup Tool so that the installing environment for the NetWare is automati- cally set up. After the MS-DOS is installed by the Toshiba Server Setup Tool, the environment to read the CD-ROM of NetWare is automatically set up.
Page 202: For Installing Netware 5.1 Manually
To make the MS-DOS recognize the CD-ROM drive, set up the MS-DOS environment as mentioned in the preceding step (1) and set the floppy disk labeled “DOS Disk” (created by the Toshiba Server Setup Tool) on the floppy disk drive. Then, operate as...
Page 203 _Return to driver summary _Modify 3 Insert the AMI IDE RAID NetWare Driver created with the Toshiba Server Setup Tool in the floppy disk drive. 4 Select “Add an unlisted driver <Ins>” by pressing the <Insert> key twice. 5 Press the <Enter> key to retrieve drivers contained in the floppy disk.
Page 204 Installing Software NetWare 6 Input Slot Number “10008” to MEGAIDE property. Proceed with installation by following the instructions that appear on the screen: Selecting the SCSI Riser card driver The installer detects the SCSI controller, and the following menu appears. Select “Modify,”...
Page 205 || Generic ATA/IDE/ATAPI.Adapter Additional Driver Options 3 Insert the Adaptec Ultra160 NetWare Driver created with the Toshiba Server Setup Tool in the floppy disk drive. 4 Select “Add an unlisted driver <Ins>” by pressing the <Insert> key twice. 5 Press the <Enter> key to retrieve drivers contained in the floppy disk.
Page 206 Installing Software NetWare Select “Modify,” and replace the driver according to the following procedure: The following drivers were detected for this server. Add, change,or delete device drivers as needed. Device types Platform Support Module: HotPlug Support Module: Storage adapters 1 Move the cursor to “Storage adapters” on the menu shown above with the arrow keys, and press the <Enter>...
Page 207 <Enter> key. 2 When the “List of network drivers currently selected” appears, delete the drivers with the <Del> key. 3 Insert the Intel LAN driver for NetWare created with Toshiba Server Setup Tool in the floppy disk drive. Installing Software...
Page 208: For Installing The Netware 4.2 Manually
Installing Software NetWare 4 Select “Add an unlisted driver <Ins>” by pressing the <Insert> key. 5 Press the <Enter> key to retrieve drivers contained in the floppy disk. 6 When the drivers are detected, they are added to the “List of network drivers currently selected.”...
Page 209 Selecting the driver to install the NetWare 4.2 When the NetWare installer detects the SCSI disk adapter and the network adapter, it displays a window as shown below. Choose the Server Drivers-Summary This is a summary of automatically or manually selected devices.
Page 210 LAN drivers” on the screen shown above with the arrow keys, and press the <Enter> key. 2 Insert the Adaptec Ultra160 ASPI & SCSI driver for NetWare created with the Toshiba Server Setup Tool in the floppy disk drive. 3 Select “Select an additional driver” first, and select “Install an unlisted driver <Ins>”...
Page 211 Selecting the Onboard Network Adapter driver Use the following file contained on the Intel LAN driver for Net- Ware created with the Toshiba Server Setup Tool as the Onboard NetWare Adapter driver. A: \NWSERVER\E100B.LAN 1 Select “Install an unlisted driver <Ins>” by pressing the <Insert>...
Page 212: Procedure After Installation Of The Netware
Installing Software NetWare 4 When the driver list appears, select the following driver. || CE100B.LAN || Intel(R) PRO PCI Adapter(CHSM spec 1.11)|| || IANS.LAN || Intel(R) Advanced Network Services Driver || 5 Input slot number “10005” to CE100B Parameters. Proceed with installing operation, following the instructions that appear on the screen.
Page 213: Harnesseye/Web
HarnessEye/web HarnessEye/web is a total server management application software. HarnessEye/web functions on Windows NT/2000 Server only. Installing and operation See “HarnessEye/web User's Guide” (on the Documentation CD- ROM) . Installing Software HarnessEye/web...
Page 214: Aft, Alb And Ipsec Functions
Installing Software AFT, ALB and IPSec functions AFT, ALB and IPSec functions The Network Adapter that is mounted in the server as the standard device has the adapter fault tolerance (AFT) function, adaptive load balance (ALB) function and IP Security(IPSec) function. Those functions can be utilized if an optional extension network adapter is installed.
Page 215 AFT, ALB and IPSec functions 1 Start up “Intel(R)PROSet II” from “Start” - “Settings” - “Con- trol panel”. 2 Select one LAN adapter to configure AFT/ALB on from the “Intel(R)PROSet II” adapter list, click the right mouse button, and select “Create New Team” under “Add Team”. 3 The Teaming Wizard screen is displayed.
Page 216 Installing Software AFT, ALB and IPSec functions The LAN card and the device driver for the LAN card are installed. PROSETII is installed. 2 Install AFT/ALB. 3 Open the control panel by “Start” - “Settings” - “Control panel”, and start up “Intel(R)PROSet II”. 4 Select one LAN adapter to use IPSEC functions on from the “Intel(R)PROSet II”...
Page 217: When Using On Windows 2000
13 The Behavior screen is displayed. Set as follows: Mark the “Secure initiator” checkbox at “Behavior”. Enter the temporary shared key at “Pre Shared Key”. NOTE: Any character string (alphabetics, numbers, symbols) of six characters or more can be used as the temporary shared key.
Page 218 AFT, ALB and IPSec functions Creating the PROSetII icon The PROSetII icon is used for setting AFT/ALB. 1 The Toshiba Server Setup Tool CD-ROM (supplied) in the CD-ROM drive. Note: A the screen that is displayed after the CD-ROM is inserted, click “Exit”...
Page 219 AFT, ALB and IPSec functions 2 Select a LAN adapter to which AFT/ALB is to be configured in the list of adapters in “Intel(R)PROSetII”, and select “Right click” “Add Team” 3 The “Teaming Wizard” screen is displayed. Select either “Adapter Fault Tolerance” or “Adaptive Load Balancing”, and select “Next”.
Page 220 Installing Software AFT, ALB and IPSec functions finger from the mouse button. When you do this, the “Wel- come to the IP Security Policy Wizard” screen appears. (3) In the “Welcome to the IP Security Policy Wizard” screen, click “Next”. You will be prompted to enter the name of the policy to create.
Page 221 AFT, ALB and IPSec functions checkbox, and set the same temporary shared key as in (4). When you have set the temporary shared key, select “Next”. (10)When the “IP Filter List” screen is displayed, mark the “All IP Traffic” checkbox, and select “Next”. (11)When the “Filter Action”...
Page 222 Installing Software AFT, ALB and IPSec functions (18)When the “IP Filter List” screen is displayed, make sure that the “All ICMP Traffic” checkbox is marked, and select “Next”. (19)When the “Filter Action” screen is displayed, mark the “Per- mit” checkbox, and select “Next”. The screen changes to the “Completing the New Rule Wiz- ard”...
Page 223: When Using Netware
When using NetWare: Loading of AFT or ALB is supported on NetWare 4.2 or later version. 1 Append by the LOAD statement to the server's AUTOEXEC.NCF file so that AFT or ALB are automatically loaded each time that the server is started up. Example 1: To load AFT LOAD <Dr ive>:\ <Pat h>\ NBI .NL M LOAD <Dr ive>:\ <Pat h>\ MSM .NL M...
Page 224: Auto-Shutdown Function
Manually install the auto-shutdown function by installing Harnes- sEye/web after installation of Windows NT/2000 is completed. NOTE: HarnessEye/web can also be installed automatically by automatically installing Windows 2000/NT by the Toshiba Server Setup Tool. Canceling the auto-shutdown function 1 Log into Windows NT as an Administrator (or user having equivalent privileges).
Page 225 Chapter Troubleshooting ... 204 Trouble with Application Software ... 211 Remedy When Windows NT/2000 is Usable ... 212 Remedy When Windows NT/2000 is Unusable ... 213...
Page 226: Chapter 6: Troubleshooting
Troubleshooting Troubleshooting If you sense some abnormality on the server, carry out the follow- ing checks according to the problem that is occurring. NOTE: Before you check the server cables or expansion cards, switch off the server and peripheral devices. If checks are performed on the cables or expansion cards with the power on, irreparable damage may be caused to the server and peripheral devices.
Page 227: Nothing Happens If You Press The Power Switch. Or, Nothing Appears On Screen Even Though You Can Hear The Server Running
1 Immediately switch the server off, and disconnect the plug from the AC outlet. 2 Does the installation site satisfy the environmental consider- ations (e.g. ambient temperature and humidity)? See “Environmental considerations” on page 5. 3 Are there any foreign objects blocking ventilation holes? Nothing happens if you press the power switch.
Page 228: Characters Are Distorted Or Not Displayed Properly
Troubleshooting Troubleshooting See the operating manual of the display unit. 6 When running Windows NT/2000, boot up in the VGA mode, and make sure that the settings (resolution, synchronizing fre- quency) are as supported by the display unit. Characters are distorted or not displayed properly Probable causes are faulty connection of the display signal cable or power cable, or a problem with the brightness or contrast set- tings.
Page 229: The Disk And Sts Indicators Light And Flash Amber
The power indicator on this server lights with the power cord con- nected to the AC outlet or while the server is in the power save mode in the case of Windows 2000. See “System status indicators” on page 14/page 114/page 128. See “HDD/LAN status indicators”...
Page 230: An Error Is Displayed During Post Operation, Or Post Stops Midway
Troubleshooting Troubleshooting An error is displayed during POST operation, or POST stops midway Probable causes are the motherboard, CPU, memory or keyboard malfunction, or that the BIOS setup is incompatible. Carry out the following procedure to check the cause of the trouble. If Windows NT/2000 can be used, see “Remedy When Windows NT/2000 is Usable”...
Page 231: Cannot Install The Os
See the Software Guide of the RAID controller. Cannot install the OS A probable cause is that the hard disk drive is not recognized. Carry out the following procedure to check the cause of the trouble. If this does not remedy the problem, see “Remedy When Win- dows NT/2000 is Unusable”...
Page 232: Windows Nt/2000 Is Locked Or Cannot Be Used
Troubleshooting Troubleshooting See the operating manual of the expansion card. See the operating manual of the peripheral devices. 1 Are all cables firmly and properly connected? Check only the cables within the scope described in this man- ual, and instruction manuals for expansion cards and periph- eral devices.
Page 233: The Power Button Does Not Function After Abortion
See the operating manual of Harness Eye / web See the operating manual of respective device. The power button does not function after abortion If, after abortion of the system, it cannot be started by pressing the power button, unplug the power cable once and then supply the power to the server again.
Page 234: Remedy When Windows Nt/2000 Is Usable
Disk Drive (HDD) or when the cause of the trouble cannot be specified, shut down the system for fail-safe purposes, switch the server off, and contact your Toshiba Technical Support. 7 On a system equipped with a redundant Hard Disk Drive...
Page 235: Remedy When Windows Nt/2000 Is Unusable
Remedy When Windows NT/2000 is Unusable functioning, contact your Toshiba Technical Support with the system still running. NOTE: If one of the devices has malfunctioned on a system equipped with a redundant Hard Disk Drive (HDD), the mal- functioning device can be hot-swapped.
Page 236 Troubleshooting Remedy When Windows NT/2000 is Unusable...
Page 237 Appendix System Unit ... 216 External Hard Drive Unit Z1 ... 218 External Device Bay Unit Z1 ... 219...
Page 238: Appendix A: Specifications
Unit of expansion Auxiliary Maximum capacity storage (built-in) units Additional HDD Standard disk chassis 3.5” x 2 (hot-swap specs.) FDD Option(USB) MAGNIA Z300 Pentium III 866MHz, 1 GHz 32KB/CPU 256KB/CPU 3GB (1GB x 3) 128MB/256MB/512MB/1GB 152GB (76GB x 2) 20GB, 40GB,76GB...
Page 239 RAID controller Max. disk cache capacity SCSI controller Power Standard supplies CD-ROM Keyboard Mouse LAN interface Display VRAM I/O ports Serial port USB port Mouse port Keyboard port CRT interface Device bay Expansion slots 64bit/66MHz PCI Uninterruptible power supply (UPS) Power and frequency Power consumption Environmental...
Page 240: External Hard Drive Unit Z1
External Hard Drive Unit Z1 SCSI Maximum capacity Additional HDD Expantion disk chassis Remote Power Control Remote Sensing Interface Power Standard supplies Uninterruptible power supply (UPS) Power and frequency Power consumption Environmental Micro Tower Type conditions Rack Type Dimensions (mm) Micro Tower Type Rack Type Maximum server Micro Tower Type...
Page 241: External Device Bay Unit Z1
External Device Bay Unit Z1 Support Device Remote Power Control Remote Sensing Interface Power Standard supplies Uninterruptible power supply (UPS) Power and frequency Power consumption Environmental Micro Tower Type conditions Rack Type Dimensions (mm) Micro Tower Type Rack Type Maximum server Micro Tower Type weight Rack Type...
Page 243 Appendix RGB interface ... 222 Serial interface ... 224 Keyboard/mouse interface ... 225 LAN-1/2 interface ... 226 USB-1/2 interface ... 226 Expansion slots (64bit/66MHz PCI slot) ... 227...
Page 244: Appendix B: Interfaces
Interfaces The output voltages from the I/O connectors on the back of chassis do not exceed 12V. RGB interface NOTE: In the table below, “I/O” denotes the input/output when seen from the server. Pin number Signal name Unused Meaning Red Video Signal Green Video Signal Blue Video Signal Not used...
Page 245: Rgb Interface Synchronizing Signals
Pin number Signal name Unused Unused Unused _CHSYNC _CVSYNC Unused RGB interface synchronizing signals Resolution Colors Scanning Horizontal sync (kHz) Vertical sync(Hz) The usable display mode differs according to the types of OS (operating system) and display unit used. Meaning Signal ground Not used Signal Ground...
Page 246: Serial Interface
Serial interface NOTE: In the table below, “I/O” denotes the input/output when seen from the server. Pin number Signal name Shield After converting cable Pin number Signal name Meaning Data Terminal Ready Data Set Ready Transmit Data Request To Send Receive Data Clear To Send Receive Carrier Detect...
Page 247: Keyboard/Mouse Interface
Pin number Signal name Keyboard/mouse interface NOTE: In the table below, “I/O” denotes the input/output when seen from the server. Pin number Signal name DATA Unused CLOCK Unused Meaning Request To Send Clear To Send Call Indicator Meaning Data Not used Signal ground Clock Not used...
Page 248: Lan-1/2 Interface
LAN-1/2 interface NOTE: In the table below, “I/O” denotes the input/output when seen from the server. Pin number Signal name Unused Unused Unused Unused USB-1/2 interface Pin number Signal name DATA- DATA+ Meaning Transmit Data (+) Transmit Data (-) Receive Data (+) Not used Not used Receive Data (-)
Page 249: Expansion Slots (64Bit/66Mhz Pci Slot)
Expansion slots (64bit/66MHz PCI slot) NOTE: In the table below, “I/O” denotes the input/output when seen from the server. Expansion slots (for expansion PCI cards) Pin number -12V INTB_L INTD_L PRSNT1_L Reserved PRSNT2_L Connector key Connector key Reserved PCICLK REQ_L +3.3V AD31 AD29...
Page 250 Pin number AD27 AD25 +3.3V C/BE3_L AD23 AD21 AD19 +3.3V AD17 C/BE3_L IRDY_L +3.3V DEVSEL_L LOCK_L PERR_L +3.3V SERR_L +3.3V CBEI_L AD14 AD12 AD10 3.3V-system environment Side B AD26 AD24 IDSEL +3.3V AD22 AD20 AD18 AD16 +3.3V FRAME_L TRDY_L STOP_L +3.3V SDONE SBO_L...
Page 251 Pin number Side B AD08 AD07 +3.3V AD05 AD03 AD01 +3.3V ACK64_L Reserved C/BE6_L C/BE4_L AD63 AD61 +3.3V AD59 AD57 AD55 AD53 AD51 AD49 3.3V-system environment Side A C/BE0_L +3.3V AD06 AD04 AD02 AD00 +3.3V REQ64_L C/BE7_L C/BE5_L +3.3V PAR64_L AD62 AD60 AD58...
Page 252 Pin number +3.3V AD47 AD45 AD43 AD41 AD39 AD37 +3.3V AD35 AD33 Reserved Reserved 3.3V-system environment Side B AD48 AD46 AD44 AD42 +3.3V AD40 AD38 AD36 AD34 AD32 Reserved Reserved Side A...
Page 253 Appendix Hardware setup information ... 232 Recovery Boot ... 233...
Page 254: Appendix C: Switch Setting
Switch Setting Hardware setup information Perform the following operations if the hardware setup informa- tion is to be forcibly returned to the standard settings (CMOS Clear): 1 Disconnect the AC power cable. 2 Remove the server panels, power supply unit and board for wireless card.
Page 255: Recovery Boot
7 Remove the sever panels, power supply unit and board for wireless card, and return the jumper switch to 3-4 short. 8 Install the board for wireless card, the power supply unit and server panels. 9 Connect the AC power cable again and restart your server. 10 Start the BIOS Setup Utility, set System Time and System Date and select “Load Setup Default”...
Page 256 Following message is displayed on the front panel display and the power is automatically turned off if BIOS recovery was succeeded. BIOS Recovery Boot succeeded. 6 Following message is displayed if BIOS recovery was failed. Return to step 5 and repeat recovery process. BIOS Recovery Boot failed.
Page 257 PJ47:CMOS Clear PJ723: Recovery Boot Default Jumper Switch Settings...
Page 259 Appendix...
Page 260: Appendix D: Trouble Information
Trouble Information The following information is displayed on the front panel display when a trouble occurs. Display ALARM (01) Baseboard +1.5V low. ALARM (02) Baseboard +1.5V high. ALARM (03) Baseboard +2.5V low. ALARM (04) Baseboard +2.5V high. ALARM (05) Baseboard +3.3V low. ALARM (06) Baseboard +3.3V high.
Page 261 Display ALARM (11) Baseboard +12.0V low. ALARM (12) Baseboard +12.0V high. ALARM (13) CPU1 core voltage low. ALARM (14) CPU1 core voltage high. ALARM (15) CPU2 core voltage low. ALARM (16) CPU2 core voltage high. ALARM (17) Baseboard temp high. ALARM (18) CPU1 thermal error.
Page 262 Display ALARM (31) Ex. Disk1 +5.0V low. ALARM (32) Ex. Disk1 +5.0V high. ALARM (33) Ex. Disk1 +12.0V low. ALARM (34) Ex. Disk1 +12.0V high. ALARM (35) Ex. Disk1 FAN1 RPM slow. ALARM (36) Ex. Disk1 FAN2 RPM slow. ALARM (37) Ex.
Page 263 Display ALARM (51) Ex. Disk2 temp1 high. ALARM (52) Ex. Disk2 AC lost. ALARM (53) Ex. Disk2 power sag. ALARM (54) Ex. Disk2 power supply fault. ALARM (55) Ex. Disk2 chassis intrusion. ALARM (56) Ex. Disk2 fuse blow out. ALARM (57) Ex.
Page 264 Display ALARM (71) Ex. Device Bay2 +5.0V low. ALARM (72) Ex. Device Bay2 +5.0V high. ALARM (73) Ex. Device Bay2 +12.0V low. ALARM (74) Ex. Device Bay2 +12.0V high. ALARM (75) Ex. Device Bay2 FAN1 RPM slow. ALARM (76) Ex. Device Bay2 AC lost. ALARM (77) Ex.
Page 265 Appendix Unit logs ... 244 Basic system configuration ... 245 CPUs ... 245 Memories ... 245 IDE Hard disk drives ... 246 SCSI units ... 246 Expansion cards ... 246 Expansion units ... 247 Other optional items ... 247...
Page 266: Appendix E: Unit Logs
Unit Logs Unit logs Unit logs are listed on following pages. Use these logs to record system component additions and information on removed optional items. The information that has thus been recorded may need to be used when executing various utilities. The unit logs consist of a log concerning the basic system configu- ration, and a log relating to added units (system components).
Page 267: Basic System Configuration
The positions where the model numbers and serial numbers of the system components are inscribed vary from manufacturer to man- ufacturer. See the relevant product manuals. Basic system configuration Server Motherboard Display unit Keyboard Mouse CPUs Socket Lower-side slot (CPU1) Upper-side slot (CPU2) Memories...
Page 268: Ide Hard Disk Drives
IDE Hard disk drives Slot1 Slot2 SCSI units Maker Model No./Type No. Internal Expansion cards Slot Model No./Type No. PCI-1 Capacity/ Model num- Revolutions Maker Interrupt request (IRQ) Date installed SCSI ID Date setting installed Memory Date used installed...
Page 269: Expansion Units
Expansion units Slot No. Other optional items Slot Serial port (COM1) USB1 USB2 Maker Model No./Type Maker Setting and Model No./Type No. SCSI ID Date setting installed Date others installed...

Toshiba Magnia Z300 User Manual

Chapter 1: Getting Started

Chapter 2: Installing and Removing Hardware

Chapter 3: External Unit Setup

Chapter 4: System Configuration Setup

Chapter 5: Installing Software

Chapter 6: Troubleshooting

Appendix A: Specifications

Appendix B: Interfaces

Appendix C: Switch Setting

Appendix D: Trouble Information

Appendix E: Unit Logs

Quick Links

Related Manuals for Toshiba Magnia Z300

Summary of Contents for Toshiba Magnia Z300