FILE NO. 810-200329 SERVICE MANUAL D I G I T A L V I D E O DIGITAL MEDIA SERVER SD-H400 DOCUMENT CREATED IN JAPAN, Sep., 2003...
Page 2
PREPARATION OF SERVICING Pickup Head consists of a laser diode that is very susceptible to external static electricity. Although it operates properly after replacement, if it was subject to electrostatic discharge during replacement, its life might be shortened. When replacing, use a conductive mat, soldering iron with ground wire, etc. to protect the laser diode from damage by static electricity.
SAFETY NOTICE SAFETY PRECAUTIONS LEAKAGE CURRENT CHECK Measure the AC voltage across the 1500 W resistor. Plug the AC line cord directly into a 120V AC outlet (do not use an isolation transformer for this check). Use an The test must be conducted with the AC switch on and AC voltmeter, having 5000 W per volt or more sensitivity.
CONTENTS SECTION 1 GENERAL DESCRIPTIONS 2. LOCATION OF MAIN PARTS AND 1. OPERATING INSTRUCTIONS MECHANISM PARTS 2-1. Location of Main Parts 2-2. Location of PC Boards SECTION 2 PART REPLACEMENT AND ADJUSTMENT PROCEDURES 1-2. PC Board Replacement 1. Replacement of Mechanical Parts 1-2-1.
SECTION 1 GENERAL DESCRIPTIONS 1. OPERATING INSTRUCTIONS Please refer to the owner's manual about the contents.
Page 6
2. LOCATION OF MAIN PARTS AND MECHANISM PARTS 2-1. Location of Main Parts HDD UNIT MD01 Mechanism chassis B903 FAN assembly Fig. 1-2-1 2-2. Location of PC Boards UT01 Tivo Main board U801 Power PC board UD01 DVD Main PC board UX03 Power Switch PC board UX02 KDB Front PC board...
SECTION 2 PART REPLACEMENT AND ADJUSTMENT PROCEDURES CAUTIONS BEFORE STARTING SERVICING Electronic parts are susceptible to static electricity and may easily damaged, so do not forget to ground as required. Many screws are used inside the unit. To prevent the screws from missing, dropping, etc.always use a magnetized screwdriver in servicing.
1-1-3. Front Panel 1-1-5. Mechanism Chassis Assembly 1. Remove the top cover. (Refer to item 1-1-1.) Note: 2. Remove the HDD. (Refer to item 1-1-2.) • Before removing the Mechanism chassis assembly (6), 3. Disconnect two flexible cadles (1). be sure to short-circuit the laser diode output land. 4.
1-1-6. Fan 1-1-7. Rear Panel 1. Remove a connector (1) and two screws (2) . 1. Remove ten screws (1). 2. Remove the fan (3). 2. Loosen two claws and remove the rear panel (2). Fan (3) Rear panel (2) Connector (1) Claw Screws (1)
Page 10
1-2. PC Board Replacement Note: • For the detailed information about DVD Main PC 1-2-1. DVD Main PC Board board connection, see Fig. 2-1-9. Note: • Before removing the DVD main PC board (4), be sure to short-circuit the laser diode output land. TO CNX01 (Tivo PC board) After replacing the DVD main PC board (4) and...
Page 11
1-2-2. Tivo PC Board 1-2-3. Power PC Board 1. Disconnect four connectors (1) Cautions : 2. Remove a screw (2) and four screws (3), then remove • Danger of explosion if battery is incorrectly the power PC board (4). replaced. •...
Page 12
1-2-4. KDB Front and Power Switch PC Board 1. Remove the front panel. (Refer to item 1-1-3.) 2. Remove five screws (1), then remove the stay (2). 3. Remove a screw (3) and two flexible cables (4), then remove the Power switch PC board (5). 4.
SECTION 3 SERVICING DIAGRAMS 1. CIRCUIT SYMBOLS AND SUPPLEMENTARY EXPLANATION 1-1. Precautions for Part Replacement • Using the parts other than those specified shall violate • In the schematic diagram, parts marked (ex. the regulations, and may cause troubles such as F801) are critical part to meet the safety regulations, operation failures, fire etc.
SECTION 4 PARTS LIST SAFETY PRECAUTION The parts identified by ! ( ) mark are critical for safety. Replace only with part number specified. The mounting position of replacement is to be identical with originals. The substitute replacement parts which do not have the same safety characteristics as specified in the parts list may create shock, fire or other hazards.
2. Parts list LOCATION PART NUMBER NUMBER DESCRIPTION - MECHANICAL PARTS - A101 P000386770 Front Panel A101V P000386700 Key,Cursor Support A104 P000377770 Cover,Top B903 P000386780 Fan ! MD01 P000386650 DVD Mechanism Assy S101 79089157 Switch,Tact RDSY0010 S101B P000386910 Jog Bracket WJ22 P000386790 Cable,ATAPI 40P,L220...
Page 52
LOCATION PART LOCATION PART NUMBER NUMBER DESCRIPTION NUMBER NUMBER DESCRIPTION UT01 P000386710 PC Board Assy Tivo Main - ELECTRICAL PARTS - - INTEGRATED CIRCUITS - ICY03 79089159 TOTX179 - CAPACITORS - UD01 P000386660 PC Board Assy DVD Main CTN2 P000387000 Jack,Mini Plug - INTEGRATED CIRCUITS - - MISCELLANEOUS - IC301...