FujiFilm SP-3000 Service Manual page 158

3.2 Messages and Actions
No. Message
E-4603 The control for the CLE circuit board
is abnormal.
Restart the system. If problems
persist, consult your technical
representative.
E-4604 The control for the CLE circuit board
is abnormal.
Restart the system. If problems
persist, consult your technical
representative.
E-4605 The control for the CLE circuit board
is abnormal.
Restart the system. If problems
persist, consult your technical
representative.
E-4606 The control for the CLE circuit board
is abnormal.
Restart the system. If problems
persist, consult your technical
representative.
E-4607 The control for the CLE circuit board
is abnormal.
Restart the system. If problems
persist, consult your technical
representative.
E-4608 The control for the CLE circuit board
is abnormal.
Restart the system. If problems
persist, consult your technical
representative.
E-4609 The control for the CLE circuit board
is abnormal.
Restart the system. If problems
persist, consult your technical
representative.
E-4610 The control for the CLE circuit board
is abnormal.
Restart the system. If problems
persist, consult your technical
representative.
NOTE 1: The refreshing backup can be restored (see Section 3.4).
Distributed by minilablaser.com
Factor
SKCLE-message delivery message
sending error
(Causes of the error message)
1. Faulty system software
2. Faulty CLE23 circuit board (CPU)
SKCLE-message delivery message
sending error 1
(Causes of the error message)
1. Faulty system software
2. Faulty CLE23 circuit board (CPU)
SKCLE-message delivery message
sending error 2
(Causes of the error message)
1. Faulty system software
2. Faulty CLE23 circuit board (CPU)
SKCLE-message delivery module
initialization error 1
(Causes of the error message)
1. Faulty system software
2. Faulty CLE23 circuit board (CPU)
SKCLE-message delivery module
pool obtaining error 0
(Causes of the error message)
1. Faulty system software
2. Faulty CLE23 circuit board (CPU)
SKCLE-message delivery memory
pool obtaining error 1
(Causes of the error message)
1. Faulty system software
2. Faulty CLE23 circuit board (CPU)
SKCLE-message delivery memory
pool release error 1
(Causes of the error message)
1. Faulty system software
2. Faulty CLE23 circuit board (CPU)
SKCLE-message delivery memory
pool release error 1
(Causes of the error message)
1. Faulty system software
2. Faulty CLE23 circuit board (CPU)
3-97
Actions
1. Restart the system software. If the
error occurs again, reinstall the
system software. (NOTE 1)
2. Replace the circuit board.
1. Restart the system software. If the
error occurs again, reinstall the
system software. (NOTE 1)
2. Replace the circuit board.
1. Restart the system software. If the
error occurs again, reinstall the
system software. (NOTE 1)
2. Replace the circuit board.
1. Restart the system software. If the
error occurs again, reinstall the
system software. (NOTE 1)
2. Replace the circuit board.
1. Restart the system software. If the
error occurs again, reinstall the
system software. (NOTE 1)
2. Replace the circuit board.
1. Restart the system software. If the
error occurs again, reinstall the
system software. (NOTE 1)
2. Replace the circuit board.
1. Restart the system software. If the
error occurs again, reinstall the
system software. (NOTE 1)
2. Replace the circuit board.
1. Restart the system software. If the
error occurs again, reinstall the
system software. (NOTE 1)
2. Replace the circuit board.
3