Carrier 48FC Series Controls, Start-Up, Operation And Troubleshooting page 82

DISPLAY TEXT
OUTPUTS
GENERAL OUTPUTS
COMMANDED IDF RPM
ECON CMD POSITION
CCH RELAY
PE1 RELAY
PE2 RELAY
ALARM RELAY
2POS/ERV RELAY
COOLING OUTPUTS
COMPRESSOR A1
COMP A LOADER
ODF SPEED RELAY
RH DISCH VALVE
RH LIQUID VALVE
COOL LIQUID VALVE
HEATING OUTPUTS
HEAT 1 RELAY
HEAT 2 RELAY
DISPLAY TEXT
USB
DATA ACQUISITION
TREND STATUS
TREND DURATION
TREND RATE
TREND POINTS FROM
TREND FROM USB FILE?
TREND FROM PRELIST?
EQUIP PERFORMANCE
GEN. INPUT/OUTPUT
COOL PERFORMANCE
HEAT PERFORMANCE
COOL DIAGNOSTIC
IDF DIAGNOSTIC
VENT DIAGNOSTIC
TREND GO?
SAVE CONFIGS TO FILE
SAVE CONFIGS
SAVE CONFIG STATUS
SAVE CONFIGS FROM FILE
FIND CONFIG FILE
FILE TRANSFER
BACKUP SERVICE FILES
UPGRADE SOFTWARE
FIND APPLICATION FILE
APPENDIX A: SystemVut Controller Display
Outputs Main Menu Layout
EXPANDED DISPLAY TEXT
Outputs Menu
General Outputs Menu
IDF Commanded RPM
Econo Commanded Position
CCH Relay 1 State
Power Exhaust 1 Relay
Power Exhaust 2 Relay
Alarm Output Relay State
2--- Pos Damper/ERV relay
Cooling Outputs Menu
Circuit A Compressor 1
Circuit A CMP A1 Loader
Outdoor Fan Speed Relay
Reheat Dischg Valve CirA
Reheat Liquid Valve CirA
Cooling Liq Valve CirA
Heating Outputs Menu
Heat Stage 1 Relay
Heat Stage 2 Relay
USB Main Menu Layout
EXPANDED DISPLAY TEXT
USB Menu
Data Acquisition Menu
USB TREND STATUS
USB TREND DURATION
USB TREND RATE
USB TREND POINTS FROM
TREND FROM USB FILE MENU
TREND FROM PRELIST MENU
TREND EQUIP PERFORMANCE
TREND GEN INPUTS/OUTPUTS
TREND COOL PERFORMANCE
TREND HEAT PERFORMANCE
TREND COOLING DIAGNOSTIC
TREND IDF DIAGNOSTIC
TREND VENTILATION
Start USB Trending
Save Configuration to file
Make Config Backup File
Backup File is ready
Save Configuration from file
USB Find Restore File
File Transfer Menu
BACKUP SERVICE FILES
Upgrade Software Menu
USB search for app file
VALUES UNITS
xxxx RPM
0 to 100 %
On/Off
On/Off
On/Off
On/Off
On/Off
On/Off
On/Off
On/Off
On/Off
On/Off
On/Off
On/Off
On/Off
VALUES UNITS
0=IDLE,
1=TRENDING,
2=NO POINTS,
3=USB FULL
0=1 MINUTE,
1=5 MINUTES,
2=15 MINUTES,
3=30 MINUTES,
4=1 HOUR,
5=3 HOURS,
6=8 HOURS,
7=12 HOURS,
8=1 DAYS,
9=1.5 DAYS,
10=2 DAYS,
11=3 DAYS,
12=5 DAYS,
13=1 WEEK,
14=2 WEEK,
15=4 WEEK,
16=USB FULL
1 to 300
0=FILE,
1=LIST
On/Off
On/Off
On/Off
On/Off
On/Off
On/Off
On/Off
Yes/No
Start/Stop
0=IDLE,
1=SUCCESS,
2=FAILURE
Yes/No
Yes/No
82
WRITE STATUS POINT
FSPD_RPM
Forcible DAMPCMD
CCHR1
Forcible PE1
Forcible PE2
Forcible ALMOUT
Forcible ERV_2POS
COMP_A1
COMP_ALD
OFR
RDV_A
RLV_A
CLV_A
HEAT_1
HEAT_2
WRITE STATUS POINT
TRNDSTAT
Command TRNDDUR
Command TRNDRATE
Command TRNDPNTS
Command TRNDEQPR
Command TRNDIO
Command TRNDCLPR
Command TRNDHTPR
Command TRNDCLDG
Command TRNDIDF
Command TRNDVENT
Command TREND_EN
Command DDBCKUP
BACKUP_R
Command BACKFILE
Command APPFILE