Install And Remove The Battery Pack Into The Tr-300; High Effi Ciency (He) Particulate Filter, Prefi Lter And Spark Arrestor - 3M Versaflo TR-300 User Instructions

Fig. 1a
4. Plug the power cord into an AC power source (100-240V). Charging will begin. Refer to Table 1 in
the Specifi cations section for a list of charger LED displays and meanings.
5. Battery pack removal (Fig. 2)
o Unplug the power cord from the electrical source.
o Release battery pack from cradle – press blue release tab on battery pack and lift out.
The TR-340 can remain attached to the TR-944N if desired. To release the cradle from the base –
press down on the oval release tab on the base, slide cradle forward and lift out. Be careful not to
pinch fi ngers as the cradle slides forward.
Battery pack charge status is indicated by pressing the indicator button on the top of the battery pack
(Fig. 3). Number of bars illuminated indicates approximate battery pack charge capacity (less than
20% to 100%). Refer to the battery pack and charger User Instructions for further information on
charging, charge status and service life of the battery packs.
Fig. 2
2
1
1
Fig. 1b
Fig. 3
6

Install and remove the Battery Pack into the TR-300

To install a charged battery pack, hold the unit so the fi lter cover faces you (Fig. 4).
o Inspect the hinge and latch on the battery pack and ensure it is clean and undamaged.
o Hook the left edge of the battery pack into its holder on the bottom of the unit (1).
o Push the right side of the battery pack into the motor/blower until the latch fully engages with
an audible click (2).
o Grasp the battery pack and gently pull to confi rm pack is locked into place.
To remove the battery pack, hold the unit so the fi lter cover faces you. Press the battery pack latch and
pull the battery pack down and out.
High Effi ciency (HE) Particulate Filter, Prefi lter and Spark Arrestor
A 3M™ TR-300 high effi ciency (HE) fi lter must always be used. The TR-3710N and TR-3710N-SG
are standard HE fi lters. The 3M™ TR-3810N and TR-3810N-SG HE fi lters are 3M recommended for
relief against nuisance level organic vapors. Nuisance level organic vapor refers to concentrations not
exceeding OSHA PEL or applicable government occupational exposure limits, whichever is lower.
The TR-3600 prefi lter is an optional accessory for select 3M™ hoods and headcovers. Check the
TR-300 NIOSH approval label to determine if the prefi lter is approved for use with your specifi c system
confi guration.
The TR-362 (TR-362-SG) is a spark arrestor/prefi lter for select 3M™ industrial headgear and 3M™
Speedglas™ welding headgear. Check the TR-300 NIOSH approval label to determine if the spark
arrestor/prefi lter is approved for use with your specifi c system confi guration. Use of the TR-362 or
TR-362-SG is mandatory for welding and in all situations where the TR-300 may be exposed to sparks,
molten metal, or other hot particulates. Failure to use the spark arrestor/prefi lter may allow the fi lter to
be damaged and allow contaminants to enter the respirator.
The TR-3600 cannot be used in combination with the TR-362 or TR-362-SG. Refer to the TR-300
NIOSH approval label to confi rm which product can be used with your system confi guration. If there
is any question regarding use of the HE fi lter, prefi lter or spark arrestor/prefi lter consult a supervisor,
occupational safety and health professional or call the 3M Technical Services help line.
Install HE fi lter and if using the TR-3600 prefi lter or TR-362 (TR-362-SG) spark arrestor/prefi lter:
1. Inspect the HE fi lter to be installed:
o Filter material is intact with no tears or other damage.
o Filter seal is present and intact with no particles, cuts, distortions or indentations present. Wipe
the fi lter seal with a clean cloth if necessary. Dispose of and replace fi lter if damage is noted or
suspected.
Fig. 4
7