Mounting Precautions - Sharp PN-HM851 Operation Manual

MOUNTING PRECAUTIONS

• This product is for use indoors.
• A mounting bracket compliant with VESA specifications is required.
• Since the monitor is heavy, consult your dealer before
installing, removing or moving the monitor.
• Mounting the monitor on the wall requires special expertise
and the work must be performed by an authorized SHARP
dealer. You should never attempt to perform any of this work
yourself. Our company will bear no responsibility for accidents
or injuries caused by improper mounting or mishandling.
• Use the monitor with the surface perpendicular to a level
surface. If necessary, the monitor may be tilted up to 20
degrees upward or downward.
• This monitor should be used at an ambient temperature
between 32°F (0°C) and 104°F (40°C). Provide enough space
around the monitor to prevent heat from accumulating inside.
For the monitor in landscape orientation
7-7/8 [200]
2
[50]
2 [50]
For the monitor in portrait orientation
7-7/8 [200]
2 2
[50] [50]
Power LED
2 [50]
• If it is difficult to provide sufficient space for any reason
such as the installation of the monitor inside a housing or
of several units side-by-side, or if the ambient temperature
may be outside of the range of 32°F (0°C) to 104°F (40°C),
install a fan or take other measures to keep the ambient
temperature within the required range.
• When installing two or more monitor units side-by-side,
provide space of at least 3/16 inch (5 mm) around them
to prevent stress on the adjacent unit or structure due to
thermal expansion.
• Temperature condition may change when using the monitor
together with the optional equipments recommended by
SHARP. In such cases, please check the temperature
condition specified by the optional equipments.
• Do not block any ventilation openings. If the temperature
inside the monitor rises, this could lead to a malfunction.
• Do not place the monitor on a device which generates heat.
Unit: inch [mm]
1-7/16 [35]
2
[50]
Unit: inch [mm]
1-7/16 [35]
• Adhere to the following when installing the monitor in its
portrait orientation. Failing to adhere to the following may
cause malfunctions.
- Install the monitor such that the power LED is located on
the bottom side.
- Set the PORTRAIT/LANDSCAPE INSTALL in the
MONITOR menu to PORTRAIT. (See page 28)
- Be sure to clamp the power cord (supplied) onto the cable
clamp attachment using the supplied cable clamp. When
clamping the power cord, take care not to stress the
terminal of the power cord. Do not bend the power cord
excessively.
Cable clamp
attachment Cable clamp
Power cord (Supplied)
Mounting the monitor laying flat on a surface
• When using this monitor laying flat on a surface (when
the monitor is tilted more than 20 degrees upward from
the perpendicular in relation to a level surface), consult an
authorized SHARP dealer because there are some specific
mounting conditions.
Adhere to the following. Failing to adhere to the following
may cause malfunctions.
- This monitor can be tilted up to 90 degrees upward.
- Set HORIZONTAL INSTALLATION in the MONITOR
menu to FACE UP. (See page 28.)
- Use this monitor at the ambient temperature between
32°F (0°C) and 86°F (30°C). Provide 7-7/8 inch (200 mm)
or more space between the monitor and the floor or other
mounting surfaces and surrounding objects to prevent
heat from accumulating inside.
If it is difficult to provide sufficient space or if the ambient
temperature may be outside of the range of 32°F (0°C) to
86°F (30°C), install a fan or take other measures to keep
the ambient temperature within the required range.
7-7/8 [200]
7-7/8
[200]
7-7/8 [200]
- Do not press hard on the screen or otherwise subject it to
impacts.
Unit: inch [mm]
7-7/8
7-7/8 [200]
[200]
7
E