Operations; Listening To A Program Source - Sherwood Newcastle R-965 Operating Instructions Manual

Operations

Notes : • Before operating this receiver with the supplied remote control, refer to " Universal Remote Controls" on page 17 for
details about operation.
• Before operating this receiver, first set this unit as desired for optimum performance, doing the OSD menu setting
procedures. (For details, refer to "OSD Menu Settings" on page 43.)

LISTENING TO A PROGRAM SOURCE

Before operation
• Enter the standby mode.
• The STANDBY button lights up in amber.
This means that the receiver is not
disconnected from the AC mains and a
small amount of current is retained to
support the operation readiness.
• To switch the power off, push the POWER switch again.
• Then power is cut off and the STANDBY button goes off.
In the standby mode, turn the power on.
1
STANDBY
STANDBY
or
• Each time the STANDBY button on the front panel
is pressed, the receiver is turned on to enter the
operating mode (the STANDBY button lights up in
blue) or off to enter the standby mode(the
STANDBY button lights up in amber).
• On the remote control, press the POWER ON button
to enter the operating mode or press the STANDBY
button to enter the standby mode.
• In the standby mode, if the INPUT SELECTOR
button is pressed, the receiver is turned on
automatically and the desired input is selected.
Switch the speakers on.
2
• Then the SPEAKER indicator (
sound can be heard from the speakers.
• When using the headphones for private listening,
press this button again to switch the speakers off,
then the SPEAKER indicator (
off mode).
STANDBY POWER ON POWER ON
POWER ON
MAIN
CH.
SET
VOL CH/
ADJUST
MUTE
DECODE
DSP DSP
RETURN
STEREO
1 3
2
4 6
5
7 9
8
OSD/MENU
DISP 0 ENT
MI M2 M3
RNC-510
) lights up and the
) goes off(speaker
24
Select the desired input source.
3
• Each time the "AUDIO" button is pressed, the input
source changes as follows:
PHONO TUNER
(frequency display)
• Each time the "VIDEO" button is pressed, the input
source changes as follows:
VIDEO 1 VIDEO 2 -------
• When the TAPE MONITOR button is set to on so that
"TAPE MON" lights up, other inputs can not be heard
from the speakers.
To listen to an input source except TAPE MONITOR, be sure
to set the TAPE MONITOR button to off.
TAPE MONITOR function
You can connect either a tape deck or a graphic equalizer to the
receiver's TAPE MONITOR jacks.
Only when you listen to the component connected to these
jacks, set the TAPE MONITOR button to on.
If you connect a 3-head tape deck, you can listen to the sound
being recorded during recording, not the source sound.
For further details, refer to the operating instructions of the
component connected.
When selecting the 8 CH DIRECT as desired
STANDBY
or
• Depending on the power amplifier setting for the surround
back channels and the surround back speaker setting, "8(, 7 or
6) CH DIRECT" is displayed and the 8(/7/6) separate analog
signals from the component connected to this input pass
through the tone, volume and bass management(if selected)
circuits only and can be heard from your speakers.(In case
that the TAPE MONITOR button is set to on, the TAPE
MONITOR button is automatically set to off.)
• Press the 8 CH DIRECT button or select the desired input
source to cancel the 8 CH direct function.
• These analog signals can be heard only. They cannot be
recorded.
POWER ON
STANDBY
AUD1
TUNER VID1
CD VID2
T.MON VID3
AUX VID4
or PHONO VID5
PAGE1
CD AUX
VIDEO 6
POWER ON
AUD1
VID6 7.1IN
DTS PL2MV
DOLBY PL2MS
PCM NEO6C
MPEG NEO6M
PAGE2