Setting The System Setup - Sherwood Newcastle R-965 Operating Instructions Manual

SETTING THE SYSTEM SETUP

S Y S T E M S E T U P
D I G I T A L I N P U T S E T U P
T O NE C O N T R O L
OS D A U T O D I S P L A Y :
C UR R E N T V I D EO :
C OMP O N E N T V I D E O S E T U P
V I D E O 2 O U T :
Off
D C T R I G G ER 2 S E T U P
D . R E - M A S T E R I N G :
R E T U R N : B a c k E N T E R : S e l e c t
D . R E - M A S T E R I N G :
A / V S Y N C : 0 F r a m e
R E T U R N : B a c k ,
Note:
• When the pure audio function is activated, the TONE CONTROL cannot be selected.
When selecting the DIGITAL INPUT SETUP
• You should assign the connected DIGITAL INs to the desired of CD, AUX and VIDEO 1~6.
(For details, refer to "CONNECTING DIGITAL INs and OUTs" on page 8.)
Press the CURSOR UP( )/DOWN( ) buttons to select the DIGITAL INPUT SETUP, then press the
1
ENTER button.
STANDBY
VOL
MUTE
DECODE
DSP
RETURN
STEREO
1
4
7
DISP
MI
RNC-510
Press the CURSOR UP( )/DOWN( )
2
buttons to select the desired input source.
STANDBY
VOL
DSP
RETURN
1
4
7
DISP
MI
• Each time these buttons are pressed, " " and " "
are moved to the corresponding DIGITAL IN.
Repeat the above steps
4
connected DIGITAL INs are assigned to
the desired input sources respectively.
To assign the connected DIGITAL INs to the desired input sources respectively
To adjust the tone as desired or to select the desired cinema EQ mode.
To set the OSD AUTO DISPLAY mode as desired .
On
To select a video input source
VID 1
To assign the connected COMPONENT VIDEO INs to the desired of VIDEO 1~6.
To set the VIDEO 2 OUT mode as desired.
Off
To select the desired input source that uses the DC trigger 2 function.
To select the desired digital re-mastering mode.
Off
To adjust the A/V SYNC as desired.
: S e l e c t
POWER ON
MAIN
CH.
SET
CH/
ADJUST
DSP
3
2
6
5
9
8
OSD/MENU
0
ENT
M2 M3
POWER ON
MAIN
CH.
SET
CH/
ADJUST
MUTE
DECODE
DSP
STEREO
3
2
6
5
9
8
OSD/MENU
0
ENT
M2 M3
and until the
D I G I T A L I N P U T
C D :
A UX :
V I D E O 1 :
V I D E O 2 :
V I D E O 3 :
V I D E O 4 :
V I D E O 5 :
V I D E O 6 :
R E T U R N : B a c k
Press the CURSOR LEFT( )/RIGHT( )
3
buttons to select the desired DIGITAL IN.
STANDBY
MAIN
VOL
MUTE
DECODE
DSP
RETURN
STEREO
1
2
4
5
7
8
0
DISP
MI M2
RNC-510
• Each time these buttons are pressed, the DIGITAL
INs change.
Notes:
• When you select "None" instead of a DIGITAL IN
for an input source, the analog input is automatically
selected.
• In such a case that a DIGITAL IN is assigned to two
input sources or more, when these input sources are
selected, the digital audio signals can be heard from
the same DIGITAL IN.
53
S E T U P
COAX1
U S B
OPT1
OPT2
OPT3
COAX2
OPT4
OPT5
, : S e l e c t
POWER ON
CH.
SET
CH/
ADJUST
DSP
3
6
9
OSD/MENU
ENT
M3