Table of Contents
Advertisement
Offset
Std
HEX
Hours
Abbrev
CAST Chinese Atlantic Standard Time
WKST West Kazakhstan Standard Time
PKT
YEKT Yekaterinburg Time
UZT
TMT
45
+5
TJT
TFT
MVT Maldives Time
MAWT Mawson Time
KGT
HMT Heard and McDonald Island Time
DAVT Davis Time
[021] Account Code
Default (FFFFFF)
The account code is included when transmitting any events generated by the Communicator. (e.g., Panel Absent
Trouble). It is recommended that the account code be the same as the control panel account number. Valid range:
000001-FFFFFE. If 4 digit account codes are needed the 2 lowest digits shall be programmed as FF;(e.g., Account
1234 is programmed as:1234FF).
NOTE: Programming this Section with all 0 or F will cause a Module Configuration Trouble (yellow LED=12 flashes).
[022] Communications Format
Default (04)
Program 03 for Contact ID (CID). Program 04 for SIA. The module can be configured to send Communicator
Events in SIA or CID format. The SIA communication format follows the level 2 specifications of the SIA Digital
Communication Standard - October 1997. This format will send the account code along with its data transmission.
The transmission will look similar to the following at the receiver. Example: Nri0 ET001
Where: N = New Event; ri0 = Partition/Area identifier; ET = Panel Absent Trouble; 001 = Zone 001.
Communications Reporting Codes
Event
[023] Panel Absent Trouble
[024] Panel Absent Trouble Restore
[025] Radio Activation Restore
[026] Ethernet 1 Test Transmission
[027] Ethernet 2 Test Transmission
[028] GPRS 1 Test Transmission
[029] GPRS 2 Test Transmission
[030] FTC Restore
[023] Panel Absent Trouble
Default (FF)
Program 00 to disable this event or FF to enable. This event will occur when communications with the panel have
been lost for more than 60 seconds.
[024] Panel Absent Trouble Restore
Default (FF)
Program 00 to disable this event or FF to enable. This event will occur when communications with the control panel
have resumed.
[025] Radio Activation Restore
Default (FF)
Program 00 to disable this event or FF to enable. This event will occur after any successful Connect24 program-
ming session.
System Test Options [026 - 029]
Test Transmissions to Primary Receiver, with Backup to Secondary Receiver:
Set Ethernet Section [026] to (FF); [027] to (00). Set GPRS Section [028] to (FF); [029] to (00).
•
If the test transmission fails to the primary receiver it will backup to the secondary receiver.
•
If the test transmission fails to the secondary receiver an FTC trouble will be generated.
Test Transmission Unique to Primary and Secondary Receivers:
Set Ethernet Section [026] to (FF); [027] to (FF). Set GPRS Section [028] to (FF); [029] to (FF).
•
The module will send periodic test transmissions to each receiver independently, with no backups.
•
If the test transmission fails to any of the programmed receivers, an FTC trouble will be generated.
Location
Pakistan Time
Uzbekistan Time
Turkmenistan Time
Tajikistan Time
French Southern and Antarctic Time
Kyrgyzstan Time
SIA
Identifier
ER
RS
RP
RP
RP
RP
YK
Offset
HEX
Hours
70 - FF
Table 8: Communications Reporting Codes
SIA
Reporting
Qualifier
Code
ET
001
001
001
001
002
003
004
001
18
Table 7: Time Zone Offset (Continued)
Std
Location
Abbrev
Reserved
CID
CID
Event
Reporting
Code
Code
1
3
3
3
3
5
1
6
1
6
1
6
1
6
3
3
CID
CID
User/
Zone
55
001
55
001
52
001
A3
951
A3
952
A3
955
A3
956
54
001
Advertisement
Table of Contents
