Table of Contents
Advertisement
IMPORTANT
This installation manual shall be used in conjunction with the Alarm Controller Power Panel manual. All the
safety instructions specified within that manual shall be observed. (or equivalent). The Alarm Controller Power
Panel is referenced as the "panel" throughout this document.
The General Packet Radio Service (GPRS)/Ethernet Communicator is fixed, wall-mounted unit, located inside
the panel, and shall be installed in the location specified in these instructions.The equipment enclosure must be
fully assembled and closed, with all the necessary screws/tabs and secured to a wall before operation. Internal
wiring must be routed in a manner that prevents:
•
Excessive strain on wire and on terminal connections,
•
Interference between power limited and non power limited wiring,
•
Loosening of terminal connections, or
•
Damage of conductor insulation.
WARNING: Never install this equipment during a lightning storm!
Safety Information
The Installer must instruct the System user on each of the following:
•
Do not attempt to service this product. Opening or removing covers may expose the user to dangerous
voltages or other risks.
•
Any servicing shall be referred to trained service personnel only.
•
Use authorized accessories only with this equipment.
•
Do not stay close to the equipment during device operation.
•
Do not touch the external antenna.
Model Information
GS2060-SM: Is a GPRS Cellular alarm Communicator that sends alarm communication to Sur-Gard System I,
II, III (SG-DRL3IP), and IV (SG-DRL4IP) central station receivers via a GPRS digital cellular network.
TL260-SM: Is an Ethernet only alarm Communicator that sends alarm communication to Sur-Gard System I, II,
and III central station receivers through a wired Ethernet/Internet connection.
TL260GS-SM: Is a Dual-path GPRS/Ethernet alarm Communicator that sends alarm communication to Sur-Gard
System I, II, III, and IV central station receivers through Ethernet/Internet or a GPRS digital cellular network.
The Communicator can be used as either a backup or primary Communicator. The Communicator supports Internet
Protocol (IP) transmission of panel and Communicator events over Ethernet/Internet and/or GPRS.
The GPRS performance of the GS2060-SM or TL260GS-SM Communicator depends greatly on GSM network
coverage in the local area. The unit should not be mounted in the final location without first performing the
Communicator Placement Test on page 10 to determine the best location for radio reception (minimum of one
green LED ON). Optional antenna kits are available from DSC at: http://www.DSC.com.
NOTE: Prior to installation of the GS2060-SM or TL260GS-SM Communicator, confirm with your local
service provider that the GPRS network is available and active in the area where the Communicator will
be installed, and that radio signal strength (CSQ) is adequate.
Panel Mounting
The following Communicators are compatible with PC1616/PC1832/PC1864 panels:
• GS2060-SM (GPRS only)
• TL260-SM (Ethernet/Internet only)
• TL260GS-SM (Ethernet/Internet + GPRS dual-path)
Features
• 128-bit AES encryption via GPRS and Ethernet/Internet (NIST Validation Certificate No. 995).
• Back up or primary GPRS alarm communication.
• Ethernet LAN/WAN 10/100 BaseT (TL260-SM/TL260GS-SM only).
• Full event reporting to central station (UL/ULC listed) and ADT Pulse
• Fully redundant Ethernet/Internet and GPRS Dual-path Alarm Communication (TL260GS-SM only).
• Individual Ethernet and/or GPRS Periodic test transmission.
• Integrated call routing.
• Panel remote uploading/downloading support via GPRS and Ethernet/Internet.
• PC-LINK connection.
• Programmable Labels.
• Quad-Band Operation: 850 MHz, 900 MHz, 1800 MHz, and 1900 MHz.
• RS-422 balanced line for supplementary communication to external ADT iHub up to 1,000 ft. (305 m.).
(non UL/ULC listed application) for ADT Pulse interface.
• SIA and Contact ID (CID) formats supported.
• Signal strength and Trouble display LEDs.
• Subscriber Identity Module (SIM) card included with Communicator.
• Supervision heartbeats sent via GPRS and Ethernet/Internet.
Technical Specifications
The input voltage to the Communicator can be drawn from the Underwriters Laboratories/Underwriters Labora-
tories Canada (UL/ULC) Listed Control Panel or provided by an external UL/ULC Listed power supply rated for
the application (external power-limited source).
NOTE: The power supply must be Class II, Power Limited.
1. ADT Pulse, iControl, and iHub are trademarks of ADT Security Services. All Rights Reserved.
GENERAL
®1
, via RS-422 to ADT iHub
3
®
(non UL/ULC listed).
Advertisement
Table of Contents
