Download Print this page

Dremel 8220 Original Instructions Manual page 23

Advertisement

Available languages
  • EN

Available languages

  • ENGLISH, page 1
pressure. Do not attempt to make an excessive
depth of cut. Overstressing the wheel increases the
loading and susceptibility to twisting or snagging of
the wheel in the cut and the possibility of kickback or
wheel breakage.
d. Do not position your hand in line with and behind
the rotating wheel. When the wheel, at the point of
operation, is moving away from your hand, the possible
kickback may propel the spinning wheel and the power
tool directly at you.
e. When wheel is pinched, snagged or when
interrupting a cut for any reason, switch off the
power tool and hold the power tool motionless until
the wheel comes to a complete stop. Never attempt
to remove the cut-off wheel from the cut while the
wheel is in motion otherwise kickback may occur.
Investigate and take corrective action to eliminate the
cause of wheel pinching or snagging.
f.
Do not restart the cutting operation in the
workpiece. Let the wheel reach full speed and
carefully re-enter the cut. The wheel may bind, walk
up or kickback if the power tool is restarted in the
workpiece.
g. Support panels or any oversized workpiece to
minimize the risk of wheel pinching and kickback.
Large workpieces tend to sag under their own weight.
Supports must be placed under the workpiece near the
line of cut and near the edge of the workpiece on both
sides of the wheel.
h. Use extra caution when making a "pocket cut" into
existing walls or other blind areas. The protruding
wheel may cut gas or water pipes, electrical wiring or
objects that can cause kickback.
SAFETY WARNINGS SPECIFIC FOR
WIRE BRUSHING OPERATIONS
a. Be aware that wire bristles are thrown by the brush
even during ordinary operation. Do not overstress
the wires by applying excessive load to the brush.
The wire bristles can easily penetrate light clothing
and/or skin.
b. Allow brushes to run at operating speed for at least
one minute before using them. During this time no
one is to stand in front or in line with the brush.
Loose bristles or wires will be discharged during the
run-in time.
c. Direct the discharge of the spinning wire brush
away from you. Small particles and tiny wire
fragments may be discharged at high velocity during
the use of these brushes and may become imbedded
in your skin.
d. Do not exceed 15,000 RPM when using wire
brushes.
DO NOT WORK WITH MATERIALS
WARNING
!
CONTAINING ASBESTOS (ASBESTOS
IS CONSIDERED CARCINOGENIC).
TAKE PROTECTIVE MEASURES
WARNING
!
WHEN DURING WORK DUST CAN
DEVELOP THAT IS HARMFUL TO ONE'S HEALTH,
COMBUSTIBLE OR EXPLOSIVE (some dusts are
considered carcinogenic); wear a dust mask and work
with dust/chip extraction when connectable.
ENVIRONMENT
DISPOSAL
The machine, accessories and packaging should be sorted
for environmental-friendly recycling.
ONLY FOR EC COUNTRIES
Do not dispose of power tools into household
waste!
According the European Guideline 2012/19/EC for
Waste Electrical and Electronic Equipment and its
implementation into national right, power tools
that are no longer usable must be collected
separately and disposed of in an environmentally
correct manner.
SPECIFICATIONS
GENERAL SPECIFICATIONS
Voltage Rating . . . . . . . . . 12 V MAX
Amperage Rating . . . . . . 1,3 – 2,0 Ah
Rated Speed . . . . . . . . . . n 33000 min
Collet Capacity . . . . . . . . 0,8 mm, 1,6 mm, 2,4 mm,
3,2 mm
SPECIFICATIONS CHARGER
Input. . . . . . . . . . . . . . . . . 230 V, 50 – 60 Hz, 26 W
Output . . . . . . . . . . . . . . . 3,6 V - 12 V
Weight . . . . . . . . . . . . . . . 292Gr
EXTENSION CORDS
Use completely unrolled and safe extension cords with a
capacity of 5 Amps.
CHARGING AND BATTERIES
• This charger can be used
by children aged 8 and
above and by persons who
have physical, sensory or
mental limitations or a lack
of experience or knowledge
if a person responsible for
their safety supervises them
or has instructed them in the
safe operation of the charger
and they understand the
associated dangers
• Supervise children
• Cleaning and user
23
-1

Advertisement

loading