Table Of Contents - Bard Fusion-Tec Installation Instructions Manual

CONTENTS
List of Necessary Materials/Tools ....................6
Site Preparation ...................................................7
Model Identification .......................................... 7
New Shelter Installation vs. Retrofit Installation .. 7
Minimum Clearance .......................................... 8
Clearance to Combustibles ................................ 8
Wall-Mount Unit Mounting ..............................10
Mounting the Units ......................................... 10
Supply Air Grill Installation .................................... 10
Wall-Mount Unit Wiring ...................................16
Main Power Wiring .......................................... 16
Unit Voltage Wiring ......................................... 17
Preliminary Start Up .........................................19
Running in Stand Alone (Orphan) Mode ............ 19
LV1000 Controller Installation ........................20
LV1000 Controller .......................................... 21
Mounting the LV Controller ........................ 21
Installing Remote Indoor
Temperature/Humidity Sensor(s) ................ 22
FIGURES AND TABLES
Figure 1 FUSION-TEC Model Nomenclature ...........7
Figure 2 Dimensions ............................................9
Figure 3 Prefilling Traps on Indoor Drain Pan
Hoses .................................................... 11
Figure 4 Hanging Front Access Panel to Allow
Access to Control Panel ......................... 11
Figure 5 Fold-Out Diverter ..................................12
Figure 6 Downward Curved Diverter Blades ..........12
Figure 7 View of Installed Grille ..........................12
Figure 8 Mounting Instructions ...........................13
Figure 9 Electric Heat Clearance .........................14
Figure 10 Wall Mounting Instructions ....................14
Figure 11 Wall Mounting Instructions ....................15
Figure 12 Common Wall Mounting Installations ......15
Figure 13 Wire Routing ........................................17
WIRING: VAC Supply Wiring
Figure 14
Landing Points .....................................17
Figure 15 Adjusting the 230/208 VAC
Transformer ..........................................18
Figure 16 Cool and Heat Setpoints ........................19
Figure 17 Typical LV1000 Component Location ......20
Figure 18 LV1000 Fused Power Supply Terminal ....21
Figure 19 Remote Indoor Temperature/Humidity
Sensor Installation ................................22
Figure 20 Additional Remote Sensor Installation ....23
Figure 21 Communication Wiring (Daisy Chain) ......25
Figure 22 Communication Wiring (Alt. Method) ......25
Figure 23 Placement of Communication Filters ......26
Figure 24 Communication Wiring: Termination
at the Controller ...................................27
Figure 25 Communication Wiring: Termination
at the First Wall-Mount Unit ..................28
Figure 26 Communication Wiring: Termination
at Additional Wall-Mount Units ..............29
Manual 2100-674A
Page 2 of 41
Additional LV1000 Connections ................. 24
Communication Wiring .............................. 25
LV1000 Supply Wiring .............................. 30
System Set Up ....................................................33
TEC-EYE Hand-Held Diagnostic Tool ................ 33
Setting Up Wall-Mount Units for Operation ....... 34
1. Address Each Wall-Mount Unit .............. 34
2. Execute a Run Test on Each Unit ........... 35
3. Clear Unit Alarm Logs ........................... 35
Setting Up LV1000 for Operation ..................... 35
4. Set LV Controller Timezone and
Date/Time ............................................ 36
5. Configure Sensors................................. 37
6. Enter Total Number of Units .................. 38
7. Verify Units are Online .......................... 39
8. Clear Controller Alarm Logs ................... 39
9. Complete Installation ............................ 39
Additional Information ....................................40
Figure 27 LV1000-100 Controller Supply Wiring ....30
Figure 28 Controller Grounding Posts ....................30
WIRING: LV1000 Wiring Diagram...........32
Figure 29
Figure 30 TEC-EYE Connection to Unit Control ......33
Figure 31 TEC-EYE Display and Interface ..............33
Figure 32 Changing Unit Setup Values ..................34
Figure 33 Changing Economizer Control Type .........35
Figure 34 Executing Run Test ...............................35
Figure 35 Clearing Unit Alarm Logs .......................35
Figure 36 LV1000 Controller Display/Interface .......36
Figure 37 Changing Timezone ...............................36
Figure 38 Setting Controller Date and Time ............36
Figure 39 Configuring Indoor Humidity 1 Sensor ....37
Figure 40 Configuring Indoor Humidity 2 Sensor ....37
Figure 41 Configuring Indoor Humidity 3 Sensor ....37
Figure 42 Configuring Indoor Temp 1 Sensor ..........38
Figure 43 Configuring Indoor Temp 2 Sensor ..........38
Figure 44 Configuring Indoor Temp 3 Sensor ..........38
Figure 45 Entering Total Number of Units ..............39
Figure 46 Verifying Units .....................................39
Figure 47 Clearing LV1000 Alarm Logs .................39
Figure 48 Adjusting Sensor Offset Value ................40
Figure 49 Restoring Factory Default Settings..........40
Table 1 Clearance Required for Service Access
and Adequate Condenser Airflow ..............8
Table 2 Minimum Clearance Required to
Combustible Materials ............................8
Table 3 Electrical Specification .........................16
Table 4 LV1000-100 Terminal Block Index .........31
Table 5 LV1000/TEC-EYE Passwords (Default) ....33
Table 6 Unit Status Messages ...........................41
Table 7 LV1000 Status Messages ......................41