Daikin EBLQ05+07CAV3 Installer's Reference Manual page 49

Accessing settings – Legend for tables
You can access the installer settings using two different methods.
However, NOT all settings are accessible via both methods. If so,
the corresponding table columns in this chapter are set to N/A (not
applicable).
Method
Accessing settings via the breadcrumb in the
menu structure.
Accessing settings via the code in the
overview settings.
See also:
▪ "To access the installer settings" on page 49
▪ "8.5 Menu structure: Overview installer settings" on page 74
8.1.1 To connect the PC cable to the switch box
Prerequisite: The EKPCCAB kit is required.
1 Connect the cable with USB connection to your PC.
2 Connect the plug of the cable to X10A on A1P of the switch box
of the outdoor unit, or to X12A on A4P of the switch box of
control box EKCB07CAV3.
A
A1P
X10A
A Outdoor unit switch box
B Control box switch box
3 Pay special attention to the position of the plug!
2
NOTICE
Another cable is already connected to X10A. To connect
the PC cable to X10A, therefore temporarily disconnect
this other cable. Do NOT forget to reconnect it afterwards.
EBLQ05+07CAV3 + EDLQ05+07CAV3 + EKCB07CAV3 +
EK2CB07CAV3 + EKMBUHCA3V3 + EKMBUHCA9W1
Daikin Altherma low temperature monobloc
4P405544-1 – 2015.03
Column in tables
#
Code
B
A4P
X12A
3
4
5
8.1.2 To access the most used commands
To access the installer settings
1 Set the user permission level to Installer.
2 Go to [A]: > Installer settings.
To access the overview settings
1 Set the user permission level to Installer.
2 Go to [A.8]: > Installer settings > Overview settings.
To set the user permission level to Installer
1 Set the user permission level to Adv. end user.
2 Go to [6.4]: > Information > User permission level.
3 Press for more than 4 seconds.
Result: is displayed on the home pages.
4 If you do NOT press any button for more than 1 hour or press
again for more than 4 seconds, the installer permission level
switches back to End user.
To set the user permission level to Advanced end user
1 Go to the main menu or any of its submenus:
2 Press for more than 4 seconds.
Result: The user permission level switches to Adv. end user.
Additional information is displayed and "+" is added to the menu title.
The user permission level will stay in Adv. end user until set
otherwise.
To set the user permission level to End user
1 Press for more than 4 seconds.
Result: The user permission level switches to End user. The user
interface will return to the default home screen.
To modify an overview setting
Example: Modify [1‑01] from 15 to 20.
1 Go to [A.8]: > Installer settings > Overview settings.
2 Go to the corresponding screen of the first part of the setting by
using the and button.
INFORMATION
An additional 0-digit is added to the first part of the setting
when you access the codes in the overview settings.
Example: [1‑01]: "1" will result in "01".
Overview settings
01
00 00 01 15 02 00
04 05 06
08 09 0a
0c 0d 0e
Confirm Adjust Scroll
3 Go to the corresponding second part of the setting by using the
and button.
Overview settings
01
00 00 01 15 02 00
04 05 06
08 09 0a
0c 0d 0e
Confirm Adjust Scroll
Result: The value to be modified is now highlighted.
4 Modify the value by using the
8 Configuration
.
03 00
07
0b
0f
03 00
07
0b
0f
and button.
Installer reference guide
49