Maintenance; Maintenance Instructions; Log Replacement; Door And Glass Gasket - Regency ULTIMATE U38 Owners & Installation Manual

MAINTENANCE

INSTRUCTIONS
1) Always shut the valve off before cleaning. For
relighting, refer to lighting instructions. Keep
the burner and control compartment clean by
brushing and vacuuming at least once a year.
When cleaning the logs, use a soft clean brush
as the logs are fragile and easily damaged.
2) Clean glass (never when unit is hot), appliance,
louvers, and door with a damp cloth. Never
use an abrasive cleaner. The gold louvers
(and optional gold door) may be scratched if
abrasives are used to clean them.
The heater is finished in a heat resistant paint
and should only be refinished with heat resist-
ant paint (not with wall paint). Regency
StoveBright Paint - Metallic Black #6309.
3) Make a periodic check of burner for proper
position and condition. Visually check the
flame of the burner periodically, making sure
the flames are steady; not lifting or floating.
If there is a problem, call a qualified service
person.
4) The appliance and venting system must be
inspected before use, and at least annually,
by a qualified field service person, to ensure
that the flow of combustion and ventilation air
is not obstructed.
During the annual service call, the burners
should be removed from the burner tray and
cleaned. Replace the embers - do not block
the pilot or burner ports.
5) Keep the area near the appliance clear and
free from combustible materials, gasoline and
other flammable
vapours and liquids.
WARNING: CHILDREN AND ADULTS
SHOULD BE ALERTED TO THE HAZ-
ARDS OF HIGH SURFACE TEMPERA-
TURE AND SHOULD STAY AWAY TO
AVOID BURNS OR CLOTHING IGNI-
TION. YOUNG CHILDREN SHOULD
BE CAREFULLY SUPERVISED WHEN
THEY ARE IN THE SAME ROOM AS
THE APPLIANCE.
CAUTION: ANY SAFETY SCREEN
OR GUARD REMOVED FOR SER-
VICING AN APPLIANCE MUST BE
REPLACED PRIOR TO OPERATING
THE APPLIANCE.
CLOTHING OR OTHER FLAM-
MABLE MATERIAL SHOULD NOT
BE PLACED ON OR NEAR THE
APPLIANCE.
DO NOT USE THIS APPLIANCE IF
ANY PART HAS BEEN UNDER WA-
TER. IMMEDIATELY CALL A QUALI-
FIED SERVICE TECHNICIAN TO
INSPECT THE APPLIANCE AND TO
REPLACE ANY PART OF CONTROL
SYSTEM AND ANY GAS CONTROL
WHICH HAS BEEN UNDER WATER.
6) Verify proper operation after servicing.
uses
®

LOG REPLACEMENT

The unit should never be used with broken logs.
Turn off the gas valve and allow the unit to cool
before opening door to carefully remove the logs.
The pilot light generates enough heat to burn
someone. If for any reason a log should need
replacement, you must use the proper replace-
ment log. The position of these logs must be as
shown in the diagram under Log Installation.
Note: Improper positioning of logs may cre-
ate carbon build-up and will alter
the unit's performance which is not
covered under warranty.
DOOR AND GLASS
GASKET
If the door gasket requires replacement use
7/8" diameter oval door gasket (Part # 846-570).
The glass requires 5/8" flat glass gasket. See
your Regency dealer.
®

GLASS REPLACEMENT

Your Regency stove is supplied with high
®
temperature, 5 mm Neoceram ceramic glass
that will withstand the highest heat that your
unit will produce. In the event that you break
your glass, purchase your replacement from
an authorized Regency
the step-by-step instructions for replacement.
Never operate your unit with broken glass.
WARNING: Do not operate appliance with
the glass front removed, cracked or broken.
Replacement of the glass should be done
by a licensed or qualified service person.
dealer only, and follow
®
Regency U38-10 ULTIMATE Freestanding Gas Stove
®
maintenance
|
23
| 23