Roland XP-60 Owner's Manual page 58

Delay Time (LFO delay time)
When the Fade Mode parameter is set to ON-IN, this para-
meter specifies the time from key press to when the LFO
begins to take effect. When the ON-OUT is selected, this
parameter sets the time over which the LFO continues to be
active after key press.
When the Fade Mode parameter is set to OFF-IN, this para-
meter specifies the time from key release to when the LFO
begins to take effect. When OFF-OUT is selected, this para-
meter sets the time over which the LFO continues to be
active after key release.
Refer to the Fade Mode parameter diagrams.
Fade Time (LFO fade time)
Specifies time after the delay time until the LFO amplitude
reaches maximum (or minimum).
Refer to the Fade Mode parameter diagrams.
Offset (LFO level offset)
Adjusts the LFO waveform up or down from the center
value (pitch or cutoff frequency). Positive (+) settings will
move the waveform up from the center value. Negative (-)
settings will move it down from the center value.
...........................................................................................................
<Depth (LFO depth)>
The Depth parameters adjust how LFO affects each parame-
ter. Applying LFO to the pitch creates vibrato, applying it to
the cutoff frequency will create a wah-wah effect, and apply-
ing it to the volume creates tremolo.
...........................................................................................................
Pitch (Pitch LFO depth)
Adjusts degree to which LFO influences pitch.
Filter (Filter LFO depth)
Adjusts degree to which LFO influences cutoff frequency.
Level (Amplitude LFO depth)
Adjusts degree to which LFO influences volume.
Pan (Pan LFO depth)
Adjusts degree to which LFO influences panning.
Pitch or volume changes reverse in relation from each
other between positive (+) and negative (-) Depth para-
meter settings. Setting a Depth parameter to a positive
(+) value for one Tone and setting another Tone with
the same numerical value but negative (-), the modula-
tion phase for the two Tones will be in reversed from
each other. This allows you to shift back and forth
between two different Tones and cyclically move the
stereo soundfield position in combination with pan-
ning.
58
Chapter 3. Creating your own sounds
[PATCH] [F5] (LFO&Ctl) [F3] (Control)
Control Param (Control parameter) display
Specifies Tone parameters to be controlled by the Ctrl 1–3
controllers specified on the Common Control display
(PATCH/Common).
...........................................................................................................
<Control Dest:Depth (Control destination: Control depth)>
Ctrl 1–3 can simultaneously control up to four parameters
for each Tone.
For instance, filter opens by pressing down the key.
Open the Tone 1 filter with aftertouch.
Control Dest: Depth Control Dest: Depth
CUT: +63
Use Control Dest to select the parameters to be controlled by
Ctrl 1–3:
OFF: No control
PCH: Pitch
CUT: Cutoff frequency parameter (PATCH/TVF/TVF
Param)
RES: Resonance parameter (PATCH/TVF/TVF Param)
LEV: Tone Level parameter (PATCH/TVA/TVA Param)
PAN: Tone Pan parameter (PATCH/TVA/TVA Param)
MIX: Mix/EFX Send Level parameter (PATCH/Effects/
Geneal)
CHO: Chorus Send Level parameter (PATCH/Effects/
General)
REV: Reverb Send Level parameter (PATCH/Effects/
General)
PL1: Vibrato depth–Pitch parameter (PATCH/LFO&Ctl/
LFO1 Param)
PL2: Vibrato depth–Pitch parameter (PATCH/LFO&Ctl/
LFO2 Param)
FL1: Wah-Wah effect depth–Filter parameter (PATCH/
LFO&Ctl/LFO1 Param)
FL2: Wah-Wah effect depth–Filter parameter (PATCH/
LFO&Ctl/LFO2 Param)
Ctrl 2
Control Source
Aftertouch
Control Dest: Depth Control Dest: Depth
Tone 1