Roland XP-60 Owner's Manual page 218

Byte Remarks
F0H Exclusive status
41H ID number (Roland)
dev device ID (dev : 10H - 1FH)
6AH model ID (XP-60/XP-80)
12H command ID (DT1)
aaH address MSB
bbH address
ccH address
ddH address LSB
eeH data : The actual data to be transmitted. Multi-byte data
is transmitted in the order of the address.
: :
ffH data
sum checksum
F7H EOX (End Of Exclusive)
* The amount of data that is transmitted at one time is fixed for the type of
data, and only data of the fixed starting address and size will be transmit-
ted. Refer to the address and size given in "5. Parameter address map"
(p.221).
* Data whose size is greater than 128 bytes should be divided into packets of
128 bytes or less and transmitted. Successive "Data Set 1" messages
should have at least 20 ms of time interval between them.
* For the checksum please refer to page 227.
* This message is not received if Rx.Sys.Excl parameter (SYSTEM/MIDI/
MIDI Param 1) is OFF.
* This message is not received in GM mode.
This device is able to receive GS Exclusive messages only for Scale Tune set-
tings.
Data Set 1 DT1
This message transmits the actual data, and is used when you wish to set the
data of the receiving device.
status data byte
F0H 41H, dev, 42H, 12H, aaH, bbH, ccH, ddH, ... eeH, sum
Byte Remarks
F0H Exclusive status
41H ID number (Roland)
dev device ID (dev : 10H - 1FH)
42H model ID (GS)
12H command ID (DT1)
aaH address MSB
bbH address middle byte
ccH address LSB
ddH data : The actual data to be transmitted. Multi-byte data
is transmitted in the address order.
: :
eeH data
sum checksum
F7H EOX (End Of Exclusive)
* This message is not received when the Rx.Exc parameter (SYSTEM:MIDI:
SYS-EXC MIDI) is OFF.
* This message is not received in GM mode.
2. Data transmission (sound source section)
Channel Voice messages
Note Off
status 2nd byte 3rd byte
8nH kkH vvH
9nH kkH 00H
n=MIDI channel : 0H - FH (ch.1 - ch.16)
kk=Note Number : 00H - 7FH (0 - 127)
vv=Note Off Velocity : 00H - 7FH (0 - 127)
Note On
status 2nd byte 3rd byte
9nH kkH vvH
n=MIDI channel number : 0H - FH (ch.1 - ch.16)
kk=note number : 00H - 7FH (0 - 127)
vv=Note On velocity : 01H - 7FH (1 - 127)
Control Change
By selecting a controller number that corresponds to the setting of the Assign
parameter (SYSTEM/Control/Control Assign) of C1 Slider or C2 Slider
/Assign parameter (SYSTEM/Control/Pedal Control) of Pedal 1 — 4, you can
transmit any desired control change.
218
status
F7H
Chapter 12. Supplementary material
Bank Select (Controller number 0,32)
status 2nd byte 3rd byte
BnH 00H mmH
BnH 20H llH
n=MIDI channel number : 0H - FH (ch.1 - ch.16)
mm,ll=Bank number : 00 00H - 7F 7FH (bank.1 - bank.16384)
* This message is not transmitted if Tx Program Change parameter (SYS-
TEM/MIDI/MIDI Param 2) or Tx Bank Select parameter (SYSTEM/MIDI/
MIDI Param 2) is OFF.
* For the Bank Select that corresponds to each Patch, refer to section 1.
* This message is not transmitted in GM mode
Modulation (Controller number 1)
status 2nd byte 3rd byte
BnH 01H vvH
n=MIDI channel number : 0H - FH (ch.1 - ch.16)
vv=Modulation Depth : 00H - 7FH (0 - 127)
Breath type (Controller number 2)
status 2nd byte 3rd byte
BnH 02H vvH
n=MIDI channel number : 0H - FH (ch.1 - ch.16)
vv=control value : 00H - 7FH (0 - 127)
Foot type (Controller number 4)
status 2nd byte 3rd byte
BnH 04H vvH
n=MIDI channel number : 0H - FH (ch.1 - ch.16)
vv=control value : 00H - 7FH (0 - 127)
Portamento Time (Controller number 5)
status 2nd byte 3rd byte
BnH 05H vvH
n=MIDI channel number : 0H - FH (ch.1 - ch.16)
vv=Portamento Time : 00H - 7FH (0 - 127)
Volume (Controller number 7)
status 2nd byte 3rd byte
BnH 07H vvH
n=MIDI channel number : 0H - FH (ch.1 - ch.16)
vv=Volume : 00H - 7FH (0 - 127)
Panpot (Controller number 10)
status 2nd byte 3rd byte
BnH 0AH vvH
n=MIDI channel number : 0H - FH (ch.1 - ch.16)
vv=panpot : 00H - 40H - 7FH (left - center - right)
Expression (Controller number 11)
status 2nd byte 3rd byte
BnH 0BH vvH
n=MIDI channel number : 0H - FH (ch.1 - ch.16)
vv=Expression : 00H - 7FH (0 - 127)
Hold 1 (Controller number 64)
status 2nd byte 3rd byte
BnH 40H vvH
n=MIDI channel number : 0H - FH (ch.1 - ch.16)
vv=control value : 00H - 7FH (0 - 127) 0-63=OFF, 64-127=ON
Portamento (Controller number 65)
status 2nd byte 3rd byte
BnH 41H vvH
n=MIDI channel number : 0H - FH (ch.1 - ch.16)
vv=control value : 00H - 7FH (0 - 127) 0-63=OFF, 64-127=ON
Sostenuto (Controller number 66)
status 2nd byte 3rd byte
BnH 42H vvH
n=MIDI channel number : 0H - FH (ch.1 - ch.16)
vv=control value : 00H - 7FH (0 - 127) 0-63=OFF, 64-127=ON
Soft (Controller number 67)
status 2nd byte 3rd byte
BnH 43H vvH
n=MIDI channel number : 0H - FH (ch.1 - ch.16)
vv=control value : 00H - 7FH (0 - 127) 0-63=OFF, 64-127=ON