Panasonic SC-NC9 Operating Instructions Manual page 28

The QUICK SETUP enables successive settings of the items in the shaded area.
■ "Video" menu
TV Aspect
Choose the setting to suit your television
and preference.
TV Type
Select to suit the type of television.
Time Delay
When connected with an AV amplifier and
Plasma display, adjust if you notice the
audio is out of sync with the video.
Video Out (AV/Component)
Choose the video signal format to be output
from the SCART (AV) and Component
terminal.
Still Mode
Specify the type of picture shown when
paused.
NTSC Disc Output
Choose PAL 60 or NTSC output when
playing NTSC discs (➡ Video systems,
page 15).
Picture/Video Output
Change the video signal format to be output
for JPEG, MPEG4 and DivX video if picture
output is not smooth during playback.
■ "Audio" menu
PCM Digital Output
Select the maximum sampling frequency of
PCM digital output.
Check the digital input limitations of the
equipment you connect.
#5
Dolby Digital
DTS Digital Surround
#5
MPEG
Dynamic Range Compression
(Dolby Digital only)
SC-NC9
Speaker Settings (➡ page 30)
Set the delay time for your center and
surround speakers.
#4
Refer to "Frame still and field still" (➡ Glossary, page 41)
28
SC-NC9
#5
When audio is output from HDMI AV OUT terminal, and the connected equipment does not support the
item selected, the actual output will depend on the performance of this connected equipment.
• 4:3 Pan&Scan : Regular aspect television (4:3)
The sides of the widescreen picture are cut off so it
fills the screen (unless prohibited by the disc).
• 4:3 Letterbox: Regular aspect television (4:3)
Widescreen picture is shown in the letterbox style.
• 16:9 : Widescreen television (16:9)
• Standard (Direct View TV)
• CRT Projector • LCD TV/Projector
• Projection TV
• 0ms
• 60ms • 80ms • 100ms
• Video/YPbPr : Video and YPbPr
• S-Video/YPbPr : S-Video and YPbPr
• RGB/No Output : RGB only
• Automatic
• Field
• Frame
• PAL60 : When connected to a PAL television.
• NTSC: When connected to an NTSC television
• Automatic
• PAL
• NTSC/PAL60: Output will depend on "NTSC Disc Output" setting
(➡ above).
• Up to 48 kHz : Signals over 48 kHz converted to 48 or 44.1 kHz
SC-NC6
• Up to 96 kHz : Signals over 96 kHz converted to 48 or 44.1 kHz
–
–
• Bitstream
• PCM
#5
• Bitstream
• PCM
• PCM
• Bitstream
• Off
• On: Adjust for clarity even when the volume is low through
compressing the range of the lowest sound level and the highest
sound level. Convenient for late night viewing.
• Center (C):
• Surround (LS/RS):
• Plasma TV
• 20ms • 40ms
#4
: The picture is not blurred, but picture quality is lower.
#4
: Overall quality is high, but the picture may appear blurred.
Signals from copy-protected discs are converted to 48 or 44.1 kHz
irrespective of the setting.
Some equipment cannot handle sampling frequencies of 88.2 kHz,
even if it can handle 96 kHz. Read your equipment's operating
instructions for details.
Select to suit the type of equipment you
SC-NC9
connected to the HDMI AV OUT terminal (➡ page 10).
Select "Bitstream" when the equipment can decode the
bitstream (digital form of multi-channel data). Otherwise,
select "PCM".
(If the bitstream is output to the equipment without a
decoder, high levels of noise can be output and may
damage your speakers and hearing.)
0.0 /1.0/2.0/3.0/4.0/5.0 ms
0.0 /5.0/10.0/15.0 ms