Customizing The Remote Controller To Your Tv - Onkyo DR-90 Instruction Manual

Customizing the Remote Controller to Your TV

You can customize the supplied remote controller (RC-399M)
to operate your TV.
LEVEL SETUP
SENDING/
DVD RECEIVER TV
LEARNED
POWER DVD RECEIVER
SLEEP DIMMER DISPLAY
ON STANDBY
TITLE MENU SURROUND MODE
INPUT SELECTOR
ENTER
DVD TV
RETURN SETUP
VIDEO 1 TAPE
VIDEO 2 TUNER
CH SEL
1 2 3
TEST
LEVEL
TONE AUDIO SUBTITLE
4 5 6
ANGLE ZOOM
7 8 9
OPEN/
SEARCH CLEAR
CLOSE
+10 0
FR PAUSE FF POWER MUTING
TV/ VCR
CHANNEL
DOWN PLAY UP
TUNER
PRESET
RANDOM STOP SLOW
VOLUME
REPEAT A-B MEMORY
REMOTE CONTROLLER RC-399M
MEMORY
Programming the Remote Controller
Programming is carried out by copying the signal patterns of
the TV's remote control buttons.
Before programming the remote controller
• Use new batteries for the remote controller and the TV's remote
control. Using old batteries may result in a failure in programming or
cause the programmed remote controller buttons to operate
improperly.
• The remote controller and most of other remote controls transmit
infrared rays, however, if the other remote control uses another
method, programming is impossible.
• Although six buttons are prepared for operating the TV, the number
of programmable buttons varies depending on the manufacturer and
type of the other remote control.
• Turn off both the DVD Receiver and TV to prevent the units from
undesired operation during programming.
• The remote control buttons on some TVs may have more than one
function; however, only one function can be programmed per button.
• Refer also to the TV's instruction manual for details on its remote
control operation and other information.
Note
The programmed buttons of the DVD Receiver's remote controller
may lose their data if the batteries become weak or dead, or due to
other causes. In such a case, you need to repeat programming from
the beginning using the TV's remote control. Therefore, keep the TV's
remote control in a safe place even if it is not in use.
1
Set the DVD RECEIVER/LEVEL
SETUP/TV switch to TV.
LEVEL SETUP
DVD RECEIVER TV
60
SENDING/LEARNED indicator
POWER ON
LEVEL SETUP
DVD RECEIVER/
TV
LEVEL SETUP/TV switch
The following programmable buttons
control the TV when the switch is set
to TV.
POWER
POWER TV/VCR
MUTING
(When the switch is set
TV/ VCR
CHANNEL
to DVD RECEIVER, this
button operates the
TUNER
PRESET
muting function. See
page 29.)
VOLUME
VOLUME /
CHANNEL
(When the switch is set
to DVD RECEIVER, this
button is used to select
the preset channels.
See page 27.)
2
3
MEMORY
/
4
POWER
CHANNEL
TUNER
PRESET
5
One of the TV's
remote control
buttons
If the programmed buttons do not operate properly
• If the SENDING/LEARNED indicator doesn't light up when you
press one of the programmed buttons, reprogram the button.
• If the remote controller operates only at a short distance or there is
a slow response from the TV, check the batteries.
If the batteries are not weak, the pressed button is not properly
programmed. Reprogram the button.
• If the remote controller remains without batteries for 30 minutes or
more, the programmed data will be erased. In such a case, install
new batteries, then reprogram the buttons.
Erasing all the programmed functions
1 Press MEMORY.
2 Within 5 seconds, press and hold POWER ON, then
press and hold MEMORY at the same time until the
SENDING/LEARNED indicator goes off.
Place both the DVD Receiver's
remote controller and the TV's
remote control facing with each
other on a flat level surface.
TV's remote control
DVD Receiver's
remote controller
Press MEMORY.
Proceed to the next step within 15
seconds.
MUTING
Press one of the programmable
buttons on the DVD Receiver's
TV/ VCR
remote controller.
The SENDING/LEARNED indicator lights
up.
VOLUME
While the SENDING/LEARNED
indicator is lit, press the desired
TV's remote control button whose
function you wish to copy.
If the function is successfully copied, the
SENDING/LEARNED indicator goes off.
Repeat steps 3 to 5 to program other
programmable buttons.
Note
If programming has failed because the data
capacity of the programmable button has been
exceeded or other reasons, the indicator flashes
for five seconds.
Must be 5 cm to 10 cm
apart