COMPONENTS IDENTIFIED BY MARK ON THE SCHEMATIC DIAGRAM AND IN THE PARTS LIST ARE CRITICAL FOR RISK OF FIRE AND ELECTRIC SHOCK. REPLACE THESE COMPONENTS WITH ONKYO PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL. MAKE LEAKAGE-CURRENT OR RESISTANCE...
DR-S2.2 3 7 63 1515 0 SPECIFICATIONS AMPLIFIER SECTION Power Output (FTC) All channels 40 watts per channel min. LINE (VIDEO 1, VIDEO 2/CDR/PC, TV/LINE, TAPE/MD/HD) RMS. into 6 ohms two channel driven, 200 mV/50 kohms 1,000 Hz with no more than 5 % total Composite (VIDEO 1, VIDEO 2/CDR/PC) 1 Vp-p, 75 ohms harmonic distortion.
DR-S2.2 3 7 63 1515 0 SERVICE PROCEDURES-1 PROTECTION OF EYES FROM LASER BEAM DURING SERVICING This set employs two lasers. Therefore, be sure to follow Laser Diode Properties carefully the instructions below when servicing. WARNING!! Wavelength: 650 nm...
DR-S2.2 3 7 63 1515 0 SERVICE PROCEDURES-2 SERVICE PROCEDURE 1. Replacing the fuses This symbol located near the fuse indicates that the fuse used is show operating type, For continued protection against fire hazard, replace with same type fuse , For fuse rating, refer to the marking adjest to the symbol.
Page 5
DR-S2.2 3 7 63 1515 0 PC BOARD CONNECTION DIAGRAM AC IN P1701 P8004 E8102 E8101 +5VDSP E9991 U8603 U8602 U8601 E8601 P8601 TUNER UNIT JL8602A P8201A COMPONENT TERMIN NAVD-7441 DIGITAL TERMINAL Except UPP2P type PC BOARD P9992A NAETC-7442...
DR-S2.2 3 7 63 1515 0 BLOCK DIAGRAMS Acoustic LEFT 5.1ch mode Control TV/LINE SWITCH VOLUME Rec SW RIGHT (DVD DSP) MUTE TAPE MUTE Q3001 BD3811K1 SUBWOOFER 50kHz LPF 5kHz LPF NAETC-7442 CS493292-CL AK4586 CRYSTAL D/A A/D DIGITAL SIGNAL PROCESSOR...
Page 8
DR-S2.2 3 7 63 1515 0 UDD1N type only Except UDD1N NAAR-7428 FRONT FRONT LEFT LEFT SP B RELAY SP A RELAY FRONT FRONT FRONT SPEAKERS RIGHT RIGHT CENTER CENTER SURROUND LEFT LEFT SURROUND SURROUND SPEAKERS RIGHT NAAF-7510 RIGHT...
Page 9
DR-S2.2 3 7 63 1515 0 MICROPROCESSOR TERMINAL DESCRIPTION-1 Q8001: MPD784225GC-165-8BT PIN NAME ACTIVE DESCRIPTION TRAYIN Input pin of detected signal of tray state. No used (Connect to ground) No used (Connect to ground) No used (Connect to ground)
Page 10
DR-S2.2 3 7 63 1515 0 MICROPROCESSOR TERMINAL DESCRIPTION-2 Q8001: MPD784225GC-165-8BT PIN NAME ACTIVE DESCRIPTION Output pin of serial data for PLL IC of tuner unit. PLLSDO Output pin of serial clock for PLL IC of tuner unit. PLLCLK Output pin of serial latch for PLL IC of tuner unit.
DR-S2.2 3 7 63 1515 0 MICROPROCESSOR CONNECTION DIAGRAM-1 Q8001: MPD784225GC-165-8BT CENTER FRONT SPEAKER Switch which SPEAKER MAIN POWER detects insertion P7601 state of headphone TRANSFORMER RL5401 PHONES RL5402 T9991 AC IN 6ch volume with Detection circuit of Q9991...
DR-S2.2 3 7 63 1515 0 ADJUSTMENT PROCEDURES-1 TEST MODE FOR OPERATION 1. How to go in TEST MODE? [NOTE] All memories are cleared when you go in this mode. 1. Connect the power supply cord to a wall outlet.
DR-S2.2 3 7 63 1515 0 ADJUSTMENT PROCEDURES-3 OPERATION TEST-2 7. The control voltage of AV connector (UPP type only) P1801 Language General 1. FSW voltage. Video1 AV CONNECTOR 1. Connect a dummyload, 10 kohms to No.8 pin of AV connector.
Page 15
DR-S2.2 3 7 63 1515 0 ADJUSTMENT PROCEDURES-4 ADJUSTMENT OF DVD MECHANISM-1 1. Adjustment items and location Adjustment Items Tangential Radial [Mechanism Part] adjustment adjustment screw screw Tangential and Radial Height Coarse Adjustment DVD Jitter Adjustment How to initialize the Focus Sweep Setting [Electrical Part] Electrical adjustments are not required.
Page 16
3 7 63 1515 0 DR-S2.2 ADJUSTMENT PROCEDURES-5 ADJUSTMENT OF DVD MECHANISM-2 4. Connection DIGITAL INPUT COMPONENT VIDEO OUTPUT REMOTE CONTROL DIGITAL VIDEO 2 VIDEO 1 ANTENNA 2 – –VIDEO – – 1 VIDEO 2 VIDEO 1 OUTPUT COAX...
Page 17
DR-S2.2 3 7 63 1515 0 ADJUSTMENT PROCEDURES-6 ADJUSTMENT OF DVD MECHANISM-3 TEST MODE: PLAY An address is displayed < When playback with the target address of disc (DVD)> For example, when playback with # 30000 During PLAY Press keys in order...
Page 18
DR-S2.2 3 7 63 1515 0 ADJUSTMENT PROCEDURES-7 ADJUSTMENT OF DVD MECHANISM-4 DVD jitter Adjustment Preparation of adjustment Remove table(disc) in order to adjustment Tangential screw and Radial screw. Remove two screws. And remove clamper ass'y from mechanism. Lock clamper ass'y Remove four screws.
Page 19
DR-S2.2 3 7 63 1515 0 ADJUSTMENT PROCEDURES-8 ADJUSTMENT OF DVD MECHANISM-5 DVD jitter Adjustment After adjustment Move slider to the arrow direction. After you complete sdjustment attach Table(disc) in reverce procedure. Take care to re-assemble the procedure. The position of the gear Move slider to arrow.
Page 20
DR-S2.2 3 7 63 1515 0 ADJUSTMENT PROCEDURES-9 ADJUSTMENT OF DVD MECHANISM-6 DVD Jitter Adjustment Playback method of inner and outer address for the purpose is refererd to "5. TEST MODE". Use disc: GGV1025 Test mode Play the DVD test disc...
Page 21
DR-S2.2 3 7 63 1515 0 ADJUSTMENT PROCEDURES-10 ADJUSTMENT OF DVD MECHANISM-7 Initialize the Focus Sweep Setting Purpose: To set the sweep which was correct with the individual Traverse mechanism. RC-484M CLEAR Monitor Memory Clear!!! PL Region : X1 ROM Vertion : 1.128...
Page 22
DR-S2.2 3 7 63 1515 0 ADJUSTMENT PROCEDURES-11 CHECK THE ERROR RATE Setting remote controller Press the hold down DVD button, then press 1 button. Check the CD error rate CD test disc Waiting for 8 seconds Play [Exanple] CD error rate = 33 / (7.35 x 5 x 1000) = 0.9 x 10...
DR-S2.2 3 7 63 1515 0 EXPLODED VIEWS OF MECHANISM DVD TRAY LOADING MECHANISM : DT1300 DT1300 Part No.24801014 L 13942296513 PARTS LIST REF NO. PART NO. DESCRIPTION 70300470B LOADING MOTOR AS 70333502B PULLEY, GEAR 70342118 BELT 70333503C GEAR, LOADING...
Page 28
DR-S2.2 3 7 63 1515 0 EXPLODED VIEWS OF MECHANISM TRAVERSE UNIT: DB-VTV301 (Torque : 0.12 0.01 N m) (Adjustment screw) (Adjustment (Torque : 0.12 0.01 N m) screw) Screw tight L 13942296513 (Torque : 0.12 0.01 N m) The mechanical parts with no part number in the exploded views are not supplied.
DR-S2.2 3 7 63 1515 0 SCHEMATIC DIAGRAMS-9 DVD MAIN BOARD : DB-VPB303A / DB-VPB304 (1/4) (RF) RF IC IC101 LA9701M L 13942296513 CN151 Wabble Detect Circuits 2/4,3/4 (RF) CN61 IC351 M56788AFP-TBB FTS DRIVER to NAETC-7435 P0005A CN51 to NAETC-7435...
Page 44
DR-S2.2 3 7 63 1515 0 (RF) : RF SIGNAL ROUTE : RF (VIDEO) SIGNAL ROUTE : RF (AUDIO) SIGNAL ROUTE (AD) : AUDIO DATA SIGNAL ROUTE : FOCUS SERVO LOOP LINE : TRACKING SERVO LOOP LINE : SLIDER SERVO LOOP LINE...
Page 45
DR-S2.2 3 7 63 1515 0 SCHEMATIC DIAGRAMS-10 DVD MAIN BOARD : DB-VPB303A / DB-VPB304 (2/4) PGM 8M FLASH MEMORY L 13942296513 IC601 R607 6.8K FR CPU (MB91340) PD6345A u163 Page 45 http://www.xiaoyu163.com...
Page 46
DR-S2.2 3 7 63 1515 0 L 13942296513 IC608 : AUDIO (DIGITAL) SIGNAL ROUTE IC612 CN401 To NAAR-7428 CN401 u163 : Power supply Page 46 http://www.xiaoyu163.com...
Page 47
DR-S2.2 3 7 63 1515 0 SCHEMATIC DIAGRAMS-11 DVD MAIN BOARD : DB-VPB303A / DB-VPB304 (3/4) IC712 (VD) L 13942296513 IC701 BY CHIP PE5108A DVD Decoder u163 Page 47 http://www.xiaoyu163.com...
Page 48
DR-S2.2 3 7 63 1515 0 IC805 : RF (VIDEO) SIGNAL ROUTE (VD) : VIDEO DATA SIGNAL ROUTE (AD) : AUDIO DATASIGNAL ROUTE : AUDIO SIGNAL ROUTE : AUDIO (DIGITAL) SIGNAL ROUTE (VD) (VD) (VD) L 13942296513 IC801 MITSUBISHI...
Page 49
DR-S2.2 3 7 63 1515 0 SCHEMATIC DIAGRAMS-12 DVD MAIN BOARD : DB-VPB303A / DB-VPB304 (4/4) VDB-VPB304 IC881 PM0026A Pro-1 L 13942296513 (Cr) (VD) IC861 VIDEO ENCODER ADV7172KST (Cr) u163 (Cb) (Cb) Page 49 http://www.xiaoyu163.com...
Page 50
DR-S2.2 3 7 63 1515 0 (VD) : VIDEO DATASIGNAL ROUTE : V SIGNAL ROUTE : Y SIGNAL ROUTE : C SIGNAL ROUTE (Cr) : Cr SIGNAL ROUTE 304 Only (UDD1N type Only) : Y SIGNAL ROUTE (Cb) : Cb SIGNAL ROUTE...
Page 76
DR-S2.2 3 7 63 1515 0 DISASSEMBLING PROCEDURES-1 REPLACEMENT OF POWER AMPLIFIER IC (Q5001) 1. Remove the screw. Remove the screws. 2. Disconnect wire. Rear Heat sink Remove the screw. Remove the screw. Rear Front Heat sink L 13942296513 1.
Page 77
DR-S2.2 3 7 63 1515 0 DISASSEMBLING PROCEDURES-2 REPLACEMENT OF POWER AMPLIFIER IC (Q5001) Replacement power amplifier IC. Remove four screws. Power IC(Q5001) 1. Remove four screws. 2. Remove regurator PC board (NAETC-7449) Front NAETC-7449 L 13942296513 Notes in assembly 1.
Page 78
DR-S2.2 3 7 63 1515 0 DISASSEMBLING PROCEDURES-3 DVD MECHANISM: DB-VTV301 / DT-1300 The laser diode in the optical pickup block is so sensitive to static electricity, surge current and etc. That the components are liable to be broken down or its reliability remarkably deteriorated.
Page 79
DR-S2.2 3 7 63 1515 0 DISASSEMBLING PROCEDURES-4 DVD MECHANISM: DB-VTV301 / DT-1300 Remove DVD mechanism form Remove four screws. main chassis. Rotate the gear and move slider cam to Traverse unit arrow mark. slider cam L 13942296513 gear Remove the screw.
DR-S2.2 3 7 63 1515 0 GENERAL INFORMATION DIAGNOSIS SELF-DIAGNOSTIC FUNCTION OF PICKUP DEFECTIVE This unit can confirm the laser diode current value (DVD: 650nm, CD: 780nm) of pickup on the Test Mode screen. (Press the RETURN SETUP keys in order on the test mode remote control unit (GGF1067) to enter the test mode.) It's effective in case of the following condition.
DR-S2.2 3 7 63 1515 0 UPGRADE FIRMWARE-1 Prepares for upgrade firmware REMOTE CONTROLLER Monitor TV RC-484M Required to carry out check firmware Part No. 24140484 vertion and regeon cord. Required to carry out check firmware vertion and regeon cord.
Page 82
DR-S2.2 3 7 63 1515 0 UPGRADE FIRMWARE-2 Connections Rear panel view DIGITAL INPUT COMPONENT VIDEO OUTPUT DO NOT REMOTE CONTROL VIDEO 2 VIDEO 1 DIGITAL ANTENNA 2 – –VIDEO – – 1 VIDEO 2 VIDEO 1 OUTPUT connect the mains...
Page 83
DR-S2.2 3 7 63 1515 0 UPGRADE FIRMWARE-3 Flow chart In the case of replace of the DVD main board In the case of upgrade firmware Replace of the DVD main board Check the firmware Setting the regional code...
Page 84
http://www.xiaoyu163.com DRS-2.2 3 7 63 1515 0 UPGRADE FIRMWARE-4 Check the firmware Please operate it by remote controller (RC-484M). 1. Press the DVD button. 2. Press SETUP button. 3. Operate cursor button and select General menu. Refer to 4. Operate cursor button and select Setup Menu mode. Refer to Refer to 5.
Page 85
DR-S2.2 3 7 63 1515 0 UPGRADE FIRMWARE-5 Download firmware [NOTES] This procedure document supposing using Japanese PC. The program file name, the folder name, etc. are examples. 1. Start MS-DOS prompt using the start-up menu of PC. Windows of MS DOS prompt C: WINDOWS>_...
Page 86
3 7 63 1515 0 UPGRADE FIRMWARE-6 Download procedures 5. Check that the connection of PC with DR-S2.2. 6. Check that unit is in the state of NO DISC. 7. Turn ON the power supply switch of the unit. 8. Press the Enter key of PC.
Page 87
DR-S2.2 3 7 63 1515 0 UPGRADE FIRMWARE-7 Download procedures State witch download completed The state which download completed The work of download was completed satisfactory. L 13942296513 u163 Page 87 http://www.xiaoyu163.com...
Page 88
UPA4P UDS4P UGR6P FL display NO DISC 3. Turn OFF power of DR-S2.2. 4. Disconnect DR-S2.2 and the PC. Chack firmware and regional cord You check whether it is set up firmware and repional cord correctly. Refer to about check procedure.