Listening Mode Preset - Onkyo TX-NR1008 Instruction Manual

■
Gamma *2*4
–3 to 0 to +3
Adjust the balance of incoming picture R (red), G
(green), and B (blue) color data signal to the output
color data signal.
■
Red Brightness
–50 to 0 to +50
With this setting you can adjust the picture red
brightness. "–50" is the darkest. "+50" is the bright-
est.
■
*2*4
Red Contrast
–50 to 0 to +50
With this setting you can adjust red contrast. "–50" is
the least. "+50" is the greatest.
■
Green Brightness
–50 to 0 to +50
With this setting you can adjust the picture green
brightness. "–50" is the darkest. "+50" is the bright-
est.
■
Green Contrast
–50 to 0 to +50
With this setting you can adjust green contrast.
"–50" is the least. "+50" is the greatest.
■
Blue Brightness
–50 to 0 to +50
With this setting you can adjust the picture blue
brightness. "–50" is the darkest. "+50" is the bright-
est.
■
*2*4
Blue Contrast
–50 to 0 to +50
With this setting you can adjust blue contrast. "–50"
is the least. "+50" is the greatest.
Tip
*1 This procedure can also be performed on the remote controller
by using the Home menu
*2 Press CLR if you want to reset to the default value.
Note
• If you are using the analog RGB input, the following settings
have no effect: "Film Mode", "Edge Enhancement", and
"Noise Reduction".
• "Picture Adjust" is not operable when the input selector is set
to "NET/USB".
*3
When the "Game Mode" is set to "On", this setting is fixed at
"Full".
*4
When the "Picture Mode" setting is set to anything other than
"Custom", this setting cannot be used.
*5 When the "Game Mode" is set to "On"
fixed at "Video".
*6 When the "Game Mode" is set to "On"
fixed at "Off".
En
56
*2*4
*2*4
*2*4
*2*4
(➔ 27).
(➔ 54), this setting is
(➔ 54), this setting is

Listening Mode Preset

You can assign a default listening mode to each input
source that will be selected automatically when you select
each input source. For example, you can set the default lis-
tening mode to be used with Dolby Digital input signals.
You can select other listening modes during playback, but
the mode specified here will be resumed once the AV
receiver has been set to Standby.
Main menu Listening Mode Preset
1
Use q/w to select the input source that you want to
set, and then press ENTER.
The following menu appears.
5. Listening Mode Preset
1. BD/DVD
2. VCR/DVR
3. CBL/SAT
4. GAME
5. PC
6. AUX
For "TUNER" input selector only "Analog" will be
available. For "NET/USB" input source only "Digi-
tal" will be available.
Note
• If you connect an input component (such as UP-A1 series
Dock that seated iPod) to the UNIVERSAL PORT jack,
you can assign only listening modes for the analog sound
to "PORT" selector.
2
Use q/w to select the signal format that you want
to set, and then use e/r to select a listening mode.
Only listening modes that can be used with each
input signal format can be selected
The "Last Valid" option means that the listening
mode selected last will be used.
The "Straight Decode" option means that straight
decoding listening mode (Dolby Digital, DTS, etc.)
is selected.
■
Analog/PCM
With this setting, you can specify the listening mode to
be used when an analog (CD, TV, LD, VHS, MD, turn-
table, radio, cassette, cable, satellite, etc.) or PCM digi-
tal (CD, DVD, etc.) audio signal is played.
■
Mono/Multiplex Source
With this setting, you can specify the listening mode to
be used when a mono digital audio signal is played
(DVD, etc.).
■
2ch Source
With this setting, the default listening mode for 2-chan-
nel (2/0) stereo sources in a digital format, such as
Dolby Digital or DTS.
■
Dolby D/Dolby D +/TrueHD
With this setting, you can specify the listening mode to
be used when a Dolby Digital or Dolby Digital Plus for-
mat digital audio signal is played (DVD, etc.). Specifies
the default listening mode for Dolby TrueHD sources,
such as Blu-ray or HD DVD (input via HDMI).
37 to 41).
(➔