Using The Home Menu; Changing The Input Display - Onkyo TX-NR1008 Instruction Manual
Onkyo av receiver user manual
Hide thumbs
Also See for TX-NR1008:
- Firmware update (8 pages) ,
- Specifications (2 pages) ,
- Quick setup (2 pages)
Table of Contents
Advertisement
Using the Home Menu
The Home menu provides you quick access to frequently
used menus without having to go through the long stan-
dard menu. This menu enables you to change settings and
view the current information.
1
Press RECEIVER followed by HOME.
The following information will be superimposed on
the TV screen.
BD/DVD
Audio
Bass
Video
Treble
0dB
Info
Subwoofer Level
Input
Center Level
Listening Mode
Dynamic EQ
Dynamic Volume
2
Use q/w/e/r to make the desired selection.
■
Audio
*1
You can change the following settings: “Bass”,
“Treble”, “Subwoofer Level”, “Center Level”,
“Dynamic EQ”, “Dynamic Volume”, “Late
Night”, “Music Optimizer”, “Re-EQ”, “Re-
EQ(THX)” and “Audio Selector”.
See also:
52)
• “Audyssey”
(➔
60)
• “Using the Audio Settings”
(➔
■
Video
*2
You can change the following settings: “Wide
Mode”, “Picture Mode”, “Brightness”, “Con-
trast”, “Hue” and “Saturation”.
The remote controller’s VIDEO acts as a short-
cut for this menu.
See also:
54)
• “Picture Adjust”
(➔
■
Info
*3*4
You can view the information of the following
items: “Audio”, “Video” and “Tuner”.
■
Input
*4*5
You can select the input source while viewing
the information as follows: the name of input
selectors, input assignments, and radio informa-
tion, and ARC function setting.
Press ENTER to display the current input
source, followed by q/w to select the desired
input source. Pressing ENTER again switches to
the selected input source.
■
Listening Mode
You can select the listening modes that are
grouped in the following categories: “MOVIE/
TV”, “MUSIC”, “GAME” and “THX”.
Use q/w to select the category and e/r to
select the listening mode. Press ENTER to
switch to the selected listening mode.
Note
*1
If Pure Audio or Direct listening mode is selected,
“Dynamic EQ” and “Dynamic Volume” cannot be selected.
*2
Only when you have selected “Custom” in the “Picture
55), pressing ENTER allows you to adjust the fol-
Mode”
(➔
lowing items via the Home menu; “Brightness”, “Contrast”,
“Hue” and “Saturation”. Press RETURN to return to the
original Home menu.
*3
Depending on the input source and listening mode, not all
channels shown here output the sound.
*4
When you have entered a custom name in “Name Edit”
(➔
53), the input source is displayed with that name. But
even if not, the component name may be displayed if the AV
18).
receiver receives it via HDMI connection
(➔
*5
For the PORT input selector, the name of Universal Port
Option Dock will be displayed.
Changing the Input Display
When you connect an u-capable Onkyo component, you
must configure the input display so that u can work
properly.
This setting can be done only from the front panel.
1
Press TV/CD, GAME or VCR/DVR so that “TV/
CD”, “GAME” or “VCR/DVR” appears on the
display.
2
Press and hold down TV/CD, GAME or VCR/DVR
(about 3 seconds) to change the input display.
Repeat this step to select “MD”, “CDR”, “DOCK”
or “TAPE”.
For the TV/CD input selector, the input display
changes in this order:
→
→
TV/CD
MD
CDR
TAPE
DOCK
For the GAME input selector, the setting changes in
this order:
GAME ↔ DOCK
For the VCR/DVR input selector, the setting
changes in this order:
VCR/DVR ↔ DOCK
Note
• DOCK can be selected for the TV/CD, GAME or VCR/DVR
input selector, but not at the same time.
• Enter the appropriate remote control code before using the
remote controller for the first time
(➔
84).
En
Page 27
- Quick Links:
- Rear Panel
- Connecting Your Speakers
- Speaker Setup
Hide quick links:
Advertisement
Table of Contents
