Roland v-1hd Owner's Manual page 34

Appendices
Setting item
AUTO SCAN TRANS TIME 0.0 sec–0.5 sec–4.0 sec
A/B MODE
FREEZE MODE
NO SIGNAL BACK
UNFIT SIGNAL BACK
DEINTERLACE MODE
COLOR BAR OUTPUT
TEST TONE OUTPUT
MIDI Rx SOURCE
MIDI OUT
MITI Tx CHANNEL
MIDI DEVICE ID
MIDI Rx CHANNEL
MIDI Rx TEMPO CLOCK
POWER ON LOAD
PGM LED
PST LED
INPUT LED
TRANSFORMER LED
AUDIO LED
MEMORY PANEL LOAD
EFFECTS TYPE CHANGE
WIPE TYPE CHANGE
MIX TYPE CHANGE
AUTO OFF
FRAME RATE
FACTORY RESET
VERSION
34
Value
A/B, PGM/PST
ALL, SELECT
BLACK, BLUE
BLACK, BLUE, THRU
WEAVE, BOB
ON, OFF
ON, OFF
For information on remote control via MIDI, download and refer to the "V-1HD Remote Control Guide"
(PDF) from the following Roland website.
http://proav.roland.com
1–8
RED, GREEN, YELLOW, BLUE,
PURPLE, L.BLUE, WHITE
RED, GREEN, YELLOW, BLUE,
PURPLE, L.BLUE, WHITE
ON, OFF
ON, OFF
MASTER OUT, MIC, AUDIO IN,
HDMI 1, HDMI 2, HDMI 3, HDMI 4
ON, OFF
ON, OFF
ON, OFF
ON, OFF
ON, OFF
59.94, 50
—
—
Explanation
When the Auto Scan function is on, this sets the length of time for
applying a video transition.
This sets the operation mode for video transitions.
This sets the operation mode for freezes.
This sets the background color of channels that have no video input.
This sets the background color of channels on which video of an
incompatible format is input.
When set to "THRU, " video in an unsupported format is output
unchanged, allowing confirmation of the status of the input signal.
Note, however, that the video might contain additional noise artifacts.
This specifies the method used when converting interlaced input
video to progressive video.
Setting this to "ON" outputs a color bar.
Setting this to "ON" outputs a test tone.
Selecting a memory number causes the settings at the selected
memory number to be recalled at startup.
This specifies the color used when the output video channel
buttons ([A-1]–[A-4], [B-1]–[B-4]) light up.
This specifies the color used when the buttons for the video channel to
output next ([A-1]–[A-4], [B-1]–[B-4]) light up.
When set to "ON, " the [A-1]–[A-4] and [B-1]–[B-4] buttons light up,
flash, and go dark as shown below.
Button Input video status
Lighted in white Valid video is input.
Video whose format differs from the [FORMAT]
Flashing in white
switch setting is input.
Dark No video is input.
When set to "ON, " the TRANSFORMER buttons light up in white.
This specifies the audio signal monitored by the AUDIO indicator.
This sets whether the state of the operation panel is updated (ON)
or not updated (OFF) when a memory is recalled.
When set to "ON, " effect assignments are changed by holding down
the EFFECTS A [ON] button and turning the [EFFECTS A] knob.
Operation for EFFECTS B is the same.
When set to "ON, " the wipe transition pattern changes with each
press of the [WIPE] button.
When set to "ON, " the mix transition pattern changes with each
press of the [MIX] button.
This sets the Auto Off function on or off.
When set to "ON, " the power to the V-1HD is automatically turned
off if 240 minutes elapse with no operation performed on the unit.
This sets the frame rate.
This returns the unit to its factory defaults.
This displays the version of the system program.