Table of Contents
Advertisement
58 Too Many Flash Options 86
59 Incompatible <device> 86
61 Defective Disk 86
62 Disk Full 86
63 Unformatted Disk 87
64 Disk Not Supported 87
64 Unsupported Disk Format
87
80 Fuser Maintenance 87
81 Engine Code CRC Failure
87
82 Waste Bottle Nearly Full 87
82 Waste Toner Bottle Full 87
82 Waste Toner Bottle Missing
87
83 ITU Maintenance 87
84 Oiler Nearly Exhausted 87
84 Replace Oiler 87
85 ITU Maintenance 88
86 ITU Maintenance 88
87 Fuser Missing 88
88 <color> Toner Low 88
89 ITU Maintenance 88
900–999 Service <message>
88
Activating Menu Changes 74
Bin <x> Full 74
Busy 74
Canceling Fax 75
Canceling Job 75
Change <x> 75
Check <device> Connection 75
Clearing Job Accounting Stat
75
Close Door 75
Close Finisher Door 75
Close Tray X Door 75
Copying 75
Defragmenting 75
Delete All Jobs 75
Deleting Jobs 75
Disabling Menus 75
Disk Corrupted. Reformat? 75
Disk Recovery x/5 yyy% 76
Empty Hole Punch Box 76
Enabling Menus 76
Engine Warming 76
Enter PIN
=___ 76
Fax <x> 76
Flushing Buffer 76
Formatting Disk 76
Formatting Flash 76
Held Jobs may be lost 76
Held Jobs May Not Be Restored
77
Hole Punch Waste Full 77
Insert Staple Cartridge 77
Insert Tray <x> 77
Install <device> or Cancel Job
77
Invalid Engine Code 77
Invalid Network <x> Code 77
Invalid Standard Network Code
77
ITU/Fuser Maint 77
Load <x> Plain Letter 77
Load Manual 77
Load Staples 78
Load Tray <x> 78
Menus Disabled 78
Network <x> 78
Network <x>,<y> 78
Network Card Busy 78
No DRAM Installed 78
No Jobs Found. Retry? 78
Not Ready 78
Ovrflow Bin Full 78
Parallel <x> 78
Performing Self Test 78
Power Saver 79
Print Jobs on Disk 79
Printer Calibrating 79
Printing Alignment Page 79
Printing Directory List 79
Printing Font List 79
Printing Job Accounting Stat 79
Printing Menu Settings 79
Prog Engine Code 79
Prog System Code 79
Program Flash 79
Programming Disk 79
Programming Error P<x> 80
Queuing and Deleting Jobs 80
Queuing Jobs 80
Ready 80
Ready Hex 80
Reattach <device> 80
Remove Paper <specified bin>
80
Resetting Active Bin 80
Resetting Fuser Cnt Value 80
Resetting the Printer 80
Restore Held Jobs. Go/Stop?
81
Restoring Factory Defaults 81
Restoring Held Job xxx/yyy 81
Restoring Held Jobs 81
Serial <x> 81
Setup Required 81
Staples Low 81
Std Bin Full 81
Supplies 81
Tray <x> Empty 81
Tray <x> Low 81
Tray <x> Missing 82
USB <x> 82
Waiting 82
154
Multipage Border (Finishing Menu)
45
Multipage Order (Finishing Menu)
45
multipage print
border settings 45
configuring 45
order settings 45
view settings 46
Multipage Print (Finishing Menu)
45
Multipage View (Finishing Menu)
46
multipurpose feeder, configuring
56
N
Network <x> Setup (Network
Menu) 49
Network Buffer (Network Menu)
49
Network Menu 49
Job Buffering 49
MAC Binary PS 49
Network <x> Setup 49
Network Buffer 49
NPA Mode 50
PCL SmartSwitch 50
PS SmartSwitch 50
Std Net Setup 50
network port
configuring
buffer size 49
NPA mode 50
PCL SmartSwitch 50
PS SmartSwitch 50
NPA Mode (Network Menu) 50
NPA Mode (Parallel Menu) 51
NPA Mode (Serial Menu) 64
NPA Mode (USB Menu) 71
NPA mode, setting
network port 50
parallel port 51
serial port 64
USB port 71
numbers, operator panel 15
numerical values, selecting 14
O
Offset Pages (Finishing Menu) 46
Oiler (Supplies Menu) 70
operator panel 14
buttons 14
numbers 15
options
verifying installation with menu
settings page 132
Advertisement
Table of Contents
