Binks 7042-6931-4 Service Manual

Binks 7042-6931-4 Service Manual

Binks sv100 hvlp gravity feed spray gun

Advertisement

Quick Links

SERVICE MANUAL
BINKS SV100 HVLP
GRAVITY FEED SPRAY GUN
The following instructions provide the necessary information
for the proper maintenance of the Binks SV100 gravity
feed spray gun. Please read and understand all the
information in this document in order to get the maximum
performance from your new SV100 gravity spray gun.
The SV100 spray gun is the result of quality engineering
and development activity. The result is an ergonomic
product with reduced triggering effort and fine atomization.
The HVLP air cap has been specifically designed to
comply with local regulatory air quality restrictions.
The specification table details the operating parameters
of the gun to achieve those compliant conditions.
In addition, the relatively low air flow rate of the SV100
spray gun will help in containing overspray.
The SV100 spray gun should be operated under the safety
directions outlined in this literature. Your safety and the
safety of others depend on your thorough understanding
of the material contained on the Part Sheet.
If you have any questions or do not understand the
content in this literature, call your nearest service
representative.

SPECIFICATIONS

Max. Air Pressure:
175psi/12bar
For HVLP Compliance: 26 psi inlet pressure delivers
(with SV100-693K cap) 10 psi air cap pressures at
12 cfm air volume
Gun Body:
Cast Aluminum
Fluid Path:
Aluminum
Fluid Nozzle:
Stainless Steel
Fluid Needle:
Stainless Steel
Fluid Inlet Size:
3/8"-19 BSP(F)
Air Inlet Size;
1/4" NPS(M)
Gun Weight:
1.02 lbs. (461 g)
77-2875-R7.2 (6/2015)
7042-6931-4
1 / 8
EN

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 7042-6931-4 and is the answer not in the manual?

Questions and answers

Summary of Contents for Binks 7042-6931-4

  • Page 1 GRAVITY FEED SPRAY GUN 7042-6931-4 The following instructions provide the necessary information for the proper maintenance of the Binks SV100 gravity feed spray gun. Please read and understand all the information in this document in order to get the maximum performance from your new SV100 gravity spray gun.
  • Page 2 IT IS THE RESPONSIBILITY OF THE EMPLOYER TO PROVIDE THIS INFORMATION TO THE OPERATOR OF THE EQUIPMENT. FOR FURTHER SAFETY INFORMATION REGARDING THIS EQUIPMENT, SEE THE GENERAL EQUIPMENT SAFETY BOOKLET (77-5300). Binks reserves the right to modify equipment specification without prior notice. 2 / 8...
  • Page 3 VOC vapors into the atmosphere. In order to comply with these new air quality laws, Binks CLEANING GUN AND GRAVITY FEED CUP recommends one of the following two methods to clean your spray finishing equipment.
  • Page 4 Supply Atomizing pressure must be set to allow for the drop in air pressure between the regulator and the spray gun. Binks recommends Model HFRL-508 Separator/Filter Regulator. Air to Spray Gun atomizing pressure HOSE SIZE RECOMMENDATIONS WITH 60 PSI APPLIED AT AIR SUPPLY...
  • Page 5 BINKS SV100 HVLP GRAVITY FEED SPRAY GUN PARTS LIST (When ordering, please specify Part No.) ITEM PART ITEM PART DESCRIPTION QTY. DESCRIPTION QTY. SV100-693K AIR CAP ..........1 ★ — FLUID NEEDLE 1.4 mm ......1 ★ — FLUID TIP 1.4 mm w/GASKET ..... 1 ★...
  • Page 6 AIR NOZZLE, FLUID NOZZLE, FLUID NEEDLE NOTE To reduce overspray and obtain maximum efficiency always spray with the lowest possible atomizing air pressure. 1. All nozzles and needles are precision made. They 3. To clean nozzles, soak them in solvent to dissolve should be handled with care.
  • Page 7 ACCESSORIES Cleaning Brushes 29-3100-K6 Scrubs ® GFC-501 (Acetal) 20 Oz. Cup Hand Cleaner Towels 42884-214-K5 (3/8") 54-4720 (Aluminum) 1-Liter Cup 42884-215-K10 (5/8") Gravity Feed Cups These gravity feed cups are designed to be used with EXL, FLG, Compact, SV100, 95G and M1-G gravity feed spray guns.
  • Page 8 WARRANTY POLICY Binks products are covered by Finishing Brands one year materials and workmanship limited warranty. The use of any parts or accessories, from a source other than Finishing Brands, will void all warranties. For specific warranty information please contact the closest Finishing Brands location listed below.

This manual is also suitable for:

Sv100 hvlp

Table of Contents