Wyrestorm EX-2UTP-IR-50 User Manual

Dual Cat5e/6/7 Point to Point HD Extenders
Part Number EX-2UTP-IR-50
Connection and Operation
Place the IR TX emitter sensor directly over the infrared receiving
1
areas of the input source (.i.e. Blu-ray, cable/sat box). You may have
to adjust the location of this later to achieve the best performance
results. Sometimes moving the sensor to different places on the
source can improve IR performance.
Connect the IR TX emitter 3.5mm jack into the IR TX port on the
2
side TRANSMITTER balun.
Place the IR RX receiver sensor on the front of the display. You
3
may have to adjust the location of this later to achieve the best
performance and ensuring there is clear line of sight between this
sensor and any remote control you are using.
Connect their IR RX emitter 3.5mm jack into the IR RX port on the
4
side of the RECEIVER balun.
We strongly recommend using the supplied mounting brackets
!
to secure both the TRANSMITTER & RECEIVER baluns. Any
sudden movement of these devices could lead to loss of
picture and sound if connections become loose or strained,
resulting in unnecessary service call backs.
Connect the TRANSMITTER and RECEIVER baluns with 2 x
5
good quality, well terminated and tested *Cat5e/6 cables with RJ45
connectors wired to the 568B standard at both ends. Ensure all
connectors are pushed securely to each port and supported by the
connector strain relief clip to prevent them from becoming loose. The
quality of termination for every RJ45 is essential. Poor terminations
leads to intermittent performance and longer install times.
Make sure you connect your RJ45 Cat5e cables correctly – Port 1
6
to Port 1, Port 2 to Port 2 (see diagram).
Finally, add the provided 5V power supplies to both
7
TRANSMITTER and RECEIVER. We do not recommend passing
power remotely over long cable distances as this can affect the
performance of the product.
You can power transmitter and receiver units
!
via a USB 5V lead (CAB-USB-5V) for screens
or sources with spare USB ports. This often
solves power availability problems especially
at the display end.
USB to 5V Cable
Part Number CAB-USB-5V
Cat 5e Cable Performance Guide
5m 10m 15m 20m 25m
Dual Cat5e/6/7 Point to Point HD Extenders
EX-2UTP-IR-50 1080p
16ft 32ft 49ft 65ft 82ft
1080p 1080i
* PLEASE NOTE – All cable distances are on the basis of a direct runs of
cable (no patch panels or wall outlets). Please use good quality, solid conductor,
Cat5e cable. Stranded pre-made patch leads will reduce effectiveness of this
product. Please ensure Cat5e cables are installed to local electrical regulations.
Close lying electrical cables can effect product performance.
30m 35m 40m 45m 50m
98ft 114ft 131ft 147ft 164ft 196ft
Cat 5e Wiring Guide
The quality of termination for every RJ45 is essential. Poor terminations
leads to intermittent performance and longer install times.
Extending HDMI using Cat5e to 50m (164ft)
with IR source control
SOURCE INPUT
1
2
Control System
For two way IR control of the DISPLAY
from the SOURCE LOCATION, connect an
IR RX receiver cable to the transmitter.
All IR signals travel through PORT 1 so the
display can be operated by your control unit
at the SOURCE LOCATION when an IR TX
emitter is attached from the RECEIVER to
the infrared sensor of the DISPLAY.
4
60m
3
An infrared signal can also be passed from the
transmitter balun location to the display. For example,
a control system transmitting a "TV off" command.
POWER
7
TRANSMITTER
6
PORT 2
PORT 1
5
RECEIVER
6
PORT 2
PORT 1
7
POWER
DISPLAY OUTPUT
5