1. Manuals
  2. Brands
  3. Casablanca Manuals
  4. Fan
  5. Metropolitan
  6. Owner's manual

Casablanca Metropolitan Owner's Manual

Hide thumbs Also See for Metropolitan:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Owner's Manual
INTROduCTION
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
mOuNTINg ReCOmmeNdATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
FAN INSTALLATION
ConTRol fEATURES:
INTeLI•TOuCH 3 OPeRATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
TROubLeSHOOTINg INTeLI•TOuCH 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Safety and the proper operation of your Casablanca fan both require a thorough knowledge of the
product and proper installation; therefore, before attempting to install and operate your Casablanca
fan, read this owner's manual completely and carefully. Retain this manual for future reference.
CAuTION: To avoid possible electrical shock, make certain that electricity is turned off
at the circuit breaker or fuse box before attempting any installation procedure.
• CAuTION: RISK OF eLeCTRICAL SHOCK! All wiring must be performed in accordance with national and local
electrical codes. If you are unfamiliar with the wiring codes, you should use a qualified electrician. To avoid
overheating and possible damage to other equipment, do not install control to a receptacle, fluorescent light
fixture, motor operated appliance, or transformer-supplied appliance..
• This fan is designed to be installed on an existing electrical outlet box. The outlet box must be uL Listed for
ceiling fan installations, if it is not, a new box must be installed. Casablanca extension poles are available for
sloped or high ceiling installations.
• This ceiling fan requires a grounded electrical supply of 120 VAC, 60 Hz and a minimum 15 amp circuit. The
maximum current requirement for the fan with light fixture is 3.8 amps. The fan uses about 1 amp or 100 watts.
maximum light current is 2.8 amps or 340 watts of lighting.
• Where wire nuts are employed, be sure all bare wires are within the connectors. When installing the canopy
hatch, make sure all wires are within the canopy and that no wires are being pinched.
For best performance and for your warranty to be valid, use only genuine Casablanca blades, light fixtures, and accessories.
• The blades in each pack are matched for equal
weight to assure smooth fan operation. If more
than one fan is being installed, be careful not
to mix blades from different cartons.
• Inspect the contents of your carton for possible
shipping or handling damage and report any
such damage directly to your authorized
Casablanca dealer.
• It is always a good idea to have an assistant
to help with the installation.
• When cleaning, painting, or working near your
fan, be very careful of the fan and blades.
Always turn the power OFF to the ceiling fan
before servicing it, working on it, or replacing
light bulbs.
• Never insert anything into the path of the fan
blades while the fan is in operation.
• Never install a fan over a pool or spa.
• Never operate a fan that has been damaged in
any way. Contact Casablanca Fan Company
by calling toll free 1-888-227-2178, or contact
your local authorized Casablanca dealer for
assistance in obtaining service.
ConTEnTS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
READ AnD SAvE ThESE InSTRUCTIonS
SAfETy fIRST
BEfoRE yoU START
SAfE USE
(REmovE fUSE foR ThE
(TRIp BREAKER foR ThE
PN 6443Z HN0210
fUSE BoX
CIRCUIT yoU wIll BE
woRKIng on)
CIRCUIT BREAKER
CIRCUIT yoU wIll BE
woRKIng on)
18"
70"
84"
1

Advertisement

Table of Contents
loading

Related Manuals for Casablanca Metropolitan

Summary of Contents for Casablanca Metropolitan

  • Page 1 84″ Always turn the power OFF to the ceiling fan CIRCUIT BREAKER before servicing it, working on it, or replacing (TRIp BREAKER foR ThE CIRCUIT yoU wIll BE light bulbs. woRKIng on) • Never insert anything into the path of the fan blades while the fan is in operation. • Never install a fan over a pool or spa. • Never operate a fan that has been damaged in any way. Contact Casablanca Fan Company by calling toll free 1-888-227-2178, or contact your local authorized Casablanca dealer for assistance in obtaining service. PN 6443Z HN0210...

  • Page 2: Mounting Recommendations

    RECommEnDATIonS before mounting your Casablanca fan, read the following helpful recommendations. The location of the fan, air circulation, and fan size are all important factors to consider before installation. Location Ceiling fans have practical uses in almost every room in your home. We suggest you follow these mounting recommendations as you decide where to install your Casablanca fan. • For safety reasons, the fan blades must be a minimum of 7′ above the floor. • do not locate the fan in a doorway or above a swinging door. • In any installation, the tips of the blades must be at least 18″ from the wall in order to provide sufficient clearance for the blades. • In bedrooms, fans work best when mounted above the foot of the bed. • Over pool tables, be sure to provide plenty of clearance to avoid damage from pool cues. • In low ceiling locations, our optional Low Ceiling Adaptor (LCA)—available at extra cost—can be used to gain 3 ″. • In kitchens be sure to allow for open cupboard doors to clear the fan blades. • do not install a fan close to, or over, a pool or spa. High humidity combined with corrosive gases will destroy the finish and warp the blades.

  • Page 3: Installation Instructions

    (4) CRoSSBAR moUnTIng moUnTIng flAT wAShER BRACKET SCREw 1″(2) BRACKET geTTINg STARTed - CONTINued Installing a New Ceiling Fixture Outlet box using existing Ceiling Fixture Outlet box If you do not have an existing fixture located where you After turning the power OFF at its source (either circuit wish to place your Casablanca fan, an approved ceiling breaker or fuse box), lower the old fixture and disconnect fixture outlet box must be installed and wired. the wiring. Check the ceiling fixture outlet box to be sure that it is marked ‘Approved for ceiling fan mounting’. If it Warning: To reduce the risk of fire, electrical is not, a new box must be installed. shock, or personal injury, mount to outlet box marked acceptable for ceiling fan support.

  • Page 4: Crossbar Mounting Bracket Installation

    CRoSSBAR moUnTIng BRACKET InSTAllATIon CEIlIng fAn Proceed with installation as follows: AppRovED Step 1. Route the wires from the ceiling outlet box wIRIng BoX through the crossbar mounting bracket center hole. At- tach the bracket, with ground wire and ridges down, to the ‘Approved For Ceiling Fan Installation’ ceiling fixture BRACKET outlet box with the outlet box mounting hardware. CEIlIng Tighten the screws firmly, being careful not to bend the wIRIng bracket by over tightening. CRoSSBAR CAuTION: To reduce the risk moUnTIng of personal injury, use only the BRACKET mounting hardware provided with the approved outlet box to install the crossbar mounting flAT...

  • Page 5: Canopy Electrical Connections

    ® etropolitan Step 3. To hang the fan body in the canopy, hold the fan body firmly and insert the nylon ball into the canopy opening. Check that no wires were pinched. Rotate the fan body until the slot in the nylon ball fits into the pin opposite the canopy opening. BAll Note: Fan weighs 25lbs. SloT CAnopy ElECTRICAl ConnECTIonS Step 4. Attach the fan wires to the ceiling fixture outlet box wiring by twisting the bare ends of the wires together and then securing with a wire nut. Test that the connec- tion is secure by pulling on the wire nut. Connect in this 2 bLACK WIReS order: electrical Connections • gReeN leads from mounting plate and fan to gROuNd conductor of power source. Secure 2 WHITe WIReS with wire nut.

  • Page 6: Blade/Blade Holder Installation

    BlADE BlADE/BlADE holDER InSTAllATIon Step 9. Rotate the flywheel so that the screw holes can be accessed through the recessed area of the metal plate. Attach each blade/blade holder as- sembly to the motor. Tighten securely by hand only. 4/5 blade Combination Flywheel Your Casablanca fan includes our 4/5 combination flywheel. This flywheel accomodates your prefer- ence to use either 4 or 5 blades on your fan. If you desire a 4-blade fan, locate the square counterbo- res on the flywheel and use these threaded holes to mount the blades. If you desire a 5-blade fan, locate the round counterbores on the flywheel and use these threaded holes. BlADE holDER...
  • Page 7 ® etropolitan pREpARIng To InSTAll SwITCh hoUSIng CAp Step 10. Remove the three screws on the mounting plate. Set aside for Step 12. moUnTIng plATE SCREwS InSTAllIng ThE SwITCh hoUSIng CAp Step 11. Line up the three threaded holes in the rim of the switch housing with the three clearance holes in the mounting plate. Carefully slide the switch housing into the mount so that the thread-...

  • Page 8: Control Installation

    ® W-85 ContRol inStallation wAll ConTRol AnD hARDwARE (not to scale) (4) Wire Cap Wall Plate W-85 Switch bezels Switch mounting Screws White Wall Almond Wall Wall Control (1) White Screws (2) (2) White Plate(1) Plate(1) (1) Almond (2) Almond WaRning! BEZEl To avoid possible electrical shock, make cer- tain that electricity is turned off at the circuit breaker or fuse box before attempting any in- stallation or repair procedure CAuTION! NOT turning the power OFF at the circuit breaker or fuse box may cause damage to the electronics within the wall control and or the PC board on the fan.
  • Page 9 ® W-85 Wall Control Bezel replacement: - AlmonD ContinUED BEZEl Step 13c. Reinstall the rubber key pad on to the four (4) locating pins located on the almond bezel as shown in Figure #3 and #4. RUBBER KEy Figure #3 RUBBER KEy Step 13d. To attach the bezel back on to the front of the switch you will need to align the four (4) tabs on the bezel with the front of the wall control and by gently pressing on both top and button of the bezel at the same time, snap the bezel back on to the front of the switch as shown in figure #5. AlmonD loCATIng BEZEl pInS Figure #4 AlmonD BEZEl Step 13e. Check your work by pressing on the light, fan, reverse and power buttons, making sure that the buttons do not stick and that each switch functions properly.

  • Page 10: Single W-85 Installation

    W-85 ContRol inStallation inStalling thE W-85 Wall ContRol notE: W-85 Wall Control should only be installed on Casablanca's Inteli-Touch 3 fans with dOWNLIgHTS ONLY. ® The wall control installs in the same manner as an ordinary light switch, using an existing wall box and wiring. This controller is designed to signal the fan microcomputer as well as perform normal switching operations. For this reason the following precautions must be observed: 3. d o not use more than one fan per wall control. 1. u se only the Casablanca W-85 wall control. 4. N o other light fixtures or electrical appliances may 2. d o not use any additional control with your Inteli- be connected on the circuit controlled by the W-85 Touch 3 fan (for example, dimmer, or fan speed wall control. control). single W-85 installation CaUtion! ensure power is turned OFF at the breaker or fuse panel before starting installation.
  • Page 11 W-85 ContRol inStallation inStalling thE W-85 Wall ContRol notE: W-85 Wall Control should only be installed on Casablanca's Inteli-Touch 3 fans with dOWNLIgHTS ONLY. ® The wall control installs in the same manner as an ordinary light switch, using an existing wall box and wiring. This controller is designed to signal the fan microcomputer as well as perform normal switching operations. For this reason the following precautions must be observed: 3. d o not use more than one fan per wall control. 1. u se only the Casablanca W-85 wall control. 4. N o other light fixtures or electrical appliances may 2. d o not use any additional control with your Inteli- be connected on the circuit controlled by the W-85 Touch 3 fan (for example, dimmer, or fan speed wall control. control). single W-85 installation CaUtion! ensure power is turned OFF at the breaker or fuse panel before starting installation.

  • Page 12: Operation Lights

    ® oPERation PoWER The button is normally left in the on position. Always turn the power off during cleaning or servicing the fan and during thunderstorms. It is also used to exit or enter additional programs. The button must be left on to retain a previously set fan speed or light level. oPERation SPEED ContRol There are six individual speed settings for the fan; each speed is indicated by an audible tone of increasing pitch. fAn ConTRol To select the desired fan speed: ON - OFF: 1. With fan off, press and hold the button labeled . The fan blades A momentary will start rotating at the slowest speed, and will increase in steps. press of the FAN 2. Release the button when the desired speed is reached. button The fan speed is now in memory and will automatically come on at the ChAngE SpEED: same speed each time the button is used. To maintain this level Press and hold of speed, turn the fan on by pressing less than one second. To FAN button longer lower speed, turn fan off, then on by pressing and holding the than one second button until the desired speed is reached. When the fan is on, you may increase the speed by pressing and holding the button until the desired speed is reached, then release it.

  • Page 13: Changing Frequency Setting

    You will only have to change the dip switch settings in the remote if you are using more than one fan in the same area and want to control them separately. NOTe: dO NOT set dip switch setting in the remote to ‘0000’, this may cause frequency interference from other Casablanca Products. Step 1. Turn power OFF at the circuit breaker or fuse box and at the toggle switch, for the fan you want to change. Step 2. Remove the screws and switch plate from the existing switch box. Step 3. Remove the screws holding the switch in the switch box. DiP SWitChES DiP SWitChES SEt to ‘1111’...

  • Page 14: Operation Safe-Exit

    ® oPERation SaFE-Exit anD light-minDER PRogRam ® ® notE: both Light-minder and Safe-exit programs will always run at the same time. The Safe-Exit Program gives you about thirty seconds of light when you turn the lights off, enabling you to exit your home before the lights go out. To enter the Safe- Safe-Exit exit Program: 1) To operate the lights for Safe-exit Program – Press the button off for at least five seconds. 2) Turn the Power on. Immediately press the buttons in the following sequence: . Immediately press the button after an audio tone is heard from the fan controller. The lights will blink to indicate this command has been accepted. The lights will stay on for 30 seconds and then begin to dim. After thirty seconds have elapsed, the lights will turn completely off.

  • Page 15: Operation Fan-Minder ™ Program

    ® oPERation Fan-minDER PRogRam ™ The Fan-minder feature will add to your comfort when used in the bedroom. The program reduces the speed of the fan each two-hour interval to compensate for cooling night air. To enter the Fan-minder Program: 1. Turn the OFF for at least 5 seconds. 2. Turn the 3. Immediately operate the buttons in the following sequence: 4. The fan will respond with three descending tones. A timer is now initiated and the fan will reduce one speed for each two-hour interval. The fan will not, however, descend below the second lowest speed. 5. You may increase the fan speed by pressing and holding the button until the desired speed is reached, then release it. The fan will again reduce one speed for each 2 hour interval. 5. To cancel the Fan-minder Program, turn the OFF for three seconds.

  • Page 16: Troubleshooting Tips

    • Tighten the canopy screws and mounting plate assembly. make sure the wire nuts inside the canopy and switch housing are not touching the metal parts and that they have not fallen off the wire splices. Tighten as necessary. • Tighten the blade holders to the flywheel (or direct drive motor) and the blades to the bladeholder screws. • make sure all the screws in the motor housing are snug but not overly tight. Fan does not run on low speed • If fan is new, it may need to be “broken in.” Run at high speed for several days. This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. 1. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 2. This equipment has been tested and found to comply with the limits for a Class b digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna, Increase the separation between the equipment and receiver, Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Note: Any changes or modifications to the transmitter or receiver not expressly approved by Casablanca Fan Company may void one’s authority to operate this remote control.

  • Page 17: Product Specifications

    XLP-2000 ® ® model Number: 64xxZ blade Span: 44” & 54" blade Iron Pitch: 15° dimensions: A = 12" No. of blades: b = 12.2" Technology: Inteli•Touch 3 W-85 ® C = 3" NOTE: Dimension B d = 12" includes light fixture Airflow: 6,003 cfm and glass. e = 5.6" electricity use*: 119 watts Weight: 25 lbs. Airflow efficiency*: 50.5 cfm/watt...

Table of Contents