Related Manuals for ADS-tec VMT8000 series
Summary of Contents for ADS-tec VMT8000 series
- Page 1 Version 2.2 Translation of the original instruction manual Instruction manual Terminals VMT8000 series Effective as of 06.07.2015...
-
Page 2: Table Of Contents
4.5 Network connection 4.6 Serial interface COM1 4.7 Heater (optional) 5 Assembly 5.1 External device dimensions VMT8008 5.2 External device dimensions VMT8010 5.3 External device dimensions VMT8012 5.4 External device dimensions VMT8015 © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 3: Vmt8000 Series
LEGIC 9 Drives 10 Software & driver installation 11 Maintenance 11.1 Information on maintenance 11.2 Information on storage 12 Technical details 13 Service & support 13.1 ads-tec support 13.2 Company address © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 4: Notes
Furthermore, it is strictly forbidden to make any unauthorised alterations or technical modifications to the device. 1.3 Manufacturer The manufacturer of the product is ads-tec GmbH. The company is referred to in the following as ads- tec. 1.4 Relevant device documentation... -
Page 5: Safety Instructions
The symbol "Recommendation for use" indicates terms and/or conditions that strictly need to be observed to ensure optimised and/or zero-defect operation. Tips and suggestions for the efficient use of the device and software optimisation are also provided. © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 6: Symbols
StoraXe® and Big-LinX® are registered trademarks of ads-tec. All other third-party trademarks used are hereby acknowledged. In the case of infringement of trademark rights, ads-tec reserves the right to exercise all rights. 2.7 Copyright This instruction manual is protected by copyright. For the authorised user, simple usage rights are granted within the scope of the intent of the contract. -
Page 7: Environmental Conditions
2.8 Environmental conditions The device can be put into operation and used under the following conditions. Failure to observe any one of these conditions will invalidate the warranty. ads-tec cannot be held liable for any damages arising from improper use and handling. -
Page 8: Standards
This is a class A device. Class A devices may cause interference when used in residential environments. In this case, the operator can be requested to take appropriate measures and to pay any costs incurred as a result. © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 9: Operating And Safety Instructions
Hazard due to damage to device Damage caused by connected peripherals or data loss All cable lines (power supply, interface cables) should only be connected while the device is switched off and de-energised. © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 10: Operating Location
In the case of improper use, ads-tec shall not accept responsibility or liability for injury or damage that is directly or indirectly attributable to the handling of the device. -
Page 11: Treatment And Disposal Of Lithium Batteries
Recommendation for use: Always adhere to the safety measures applicable when handling components at risk of being damaged by electrostatic discharges. The provisions of DIN EN 61340-5-1 / DIN EN 61340-5-2 apply © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 12: Product Description
VMT8000 series 4 Product description 4.1 Device features Front view Description Display with touch function Front buttons Front USB Power-ON button © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... - Page 13 Rear view Description Service slot Mounting bracket (optional) Cover for third WLAN antenna Mounting points for device attachment Information: Detailed information on the device can be found in chapter "Technical details". © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen...
-
Page 14: 48 V Dc* Power Supply
Functional EMC protection is provided only if the PE-pin of the power supply is connected to earth. When mounting on mobile vehicles, a functional earth must be established for this purpose. * The UL marking only applies to 24 V DC power supply © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 15: Release Contact (Ign)
This function can be configured by using the Ignition Key Locking software tool. For example, the computer can be shut down in a time-controlled manner if voltage is no longer present at the ignition contact. Prefabricated supply cables are available from ads-tec for using the ignition function. -
Page 16: Autostart Function
It should remain closed when not in use in order to ensure the IP protection. Pos : 31 /D atentec hni k/Schnitts tell en/Netz werkansc hlus s RJ 45/Netz wer kansc hluss RJ 45 für VMT 60xx @ 2 \mod_1260451135970_6.doc @ 6856 @ © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 17: Network Connection
Ethernet network supporting the 10/100/1000Mbit standard by using the Ethernet 10/100/1000 BaseT network connector. The specifications of this network topology must be observed. If the drivers necessary for the function are not installed, they can be downloaded from the website www.ads-tec.de. 110/100Mbit... -
Page 18: Serial Interface Com1
The heater is controlled automatically by the firmware. If the temperature falls or rises to a predefined value, the heater is activated or deactivated. Intervention by the user is not necessary. © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 19: Assembly
Hazard due to excessive tightening torque - The device can be damaged if the tightening torque is not observed when the bracket is screwed on! Tighten the VESA bracket to max. 5 Nm! © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... - Page 20 VMT8000 series Description Bracket for Rittal housing connector top VESA 75 Standard bracket Table/vehicle bracket Mounting bracket left/right Bracket for Rittal housing connector bottom © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen...
-
Page 21: External Device Dimensions Vmt8008
VMT8000 series 5.1 External device dimensions VMT8008 Fig. 1: © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 22: External Device Dimensions Vmt8010
VMT8000 series 5.2 External device dimensions VMT8010 Fig. 2: © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 23: External Device Dimensions Vmt8012
VMT8000 series 5.3 External device dimensions VMT8012 Fig. 3: © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 24: External Device Dimensions Vmt8015
VMT8000 series 5.4 External device dimensions VMT8015 Fig. 4: © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 25: Putting Into Operation
Damage to the device can be caused by electrostatically sensitive components. All installation and service work performed on the device must be performed only under safe, secure and de-energised conditions. © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 26: Order Of Steps During Commissioning
6.5 Taking out of operation The device can be shut down using the ON/OFF pushbutton, the ignition function and using the software. The method to be used depends on the application case. © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 27: Available Interfaces
Functional EMC protection is provided only if the PE-pin of the power supply plug is connected to earth. When mounting on mobile vehicles, a functional earth must be established for this purpose. © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... - Page 28 Pos : 18 /D atentec hni k/Inbetri ebnahme/R eihenfolg e der Inbetriebnahme/R ei henfolge der Inbetriebnahme für VMT 60xx- Seri e @ 1\mod_1222073159179_6.doc @ 4100 @ : 19 /D atentec hni k/Inbetriebnahme/Betriebsber eitsc haft prüfen/Betriebsberei tsc haft prüfen für OPC /CPC/PLC/OTC/ITC /VMT- Serie(+M onitor e) / IPC 5100/5500/2400/1100 @ 0\mod_1158905578361_6.doc @ 381 @ © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen...
-
Page 29: Operation
Shift key (SHIFT) for activating the second keyboard level. This key must be pressed simultaneously with the desired function key. Resistive: The Shift key needs to be pressed. Afterwards the desired function key can be pressed. © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 30: Soft Keyboard
By using the soft keyboard, data can be entered via the touch screen like with an external keyboard. Graphical representation of soft keyboard © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 31: Touch Screen
Pos : 23 /D atentec hni k/Bedienung/Status-Anzeig en/SYS- LED/SYS- LED für VMT 60xx- Serie @ 2\mod_1260525540269_6.doc @ 6876 @ © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 32: Status Displays
Minimum / maximum value for static volume / display brightness is reached Pos : 24 /D atentec hni k/Sondergeräte-M odule/VMT 6000-Serie/R FID-Reader für VMT 6000- Seri e @ 2\mod_1260527463758_6.doc @ 6885 @ © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 33: Speakers
Button combination - increase volume Pos : 29 /D atentec hni k/Schnitts tell en/USB-Ansc hlus s/U SB-Ansc hl uss für VMT 60xx @ 2\mod_1260457598122_6.doc @ 6860 @ Button combination - reduce volume © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 34: Wireless
Additionally, the following security standards are supported: WEP 64 bit, 128 bit 802.11i WPA TKIP, CCMP (AES) WPA2 TKIP, CCMP (AES) WPA PSK (preshared key) WPA enterprise: EAP-TLS The specifications of this network topology must be observed. © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 35: Bluetooth (Optional)
As an option, the device can be equipped with a Bluetooth wireless module at the factory. The following Bluetooth standards are available: Option Name Range Option 1 Bluetooth 2.0 Approx. 100m Class 1 Option 2 Bluetooth 2.0 Approx. 10- Class 2 © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 36: Rfid Reader (As An Option)
For authentication, the transponder is raised to the position indicated in the image. The information on your transponder is read by the device and evaluated by a software solution. The MIFARE and LEGIC technology are used in the VMT series. Position of RFID reader © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 37: Rfid Configuration
Depending on hardware equipment, a MIFARE or LEGIC RFID reader is installed. 8.4.1 MIFARE To test the RFID function, select the "ads-tec RFID example application" via the pre-installed Configuration Center. Recommendation for use: Detailed information on the Configuration Center can be found in chapter "Configuration Center". -
Page 38: Legic
To test the RFID function, select a suitable editor (Notepad, Word) and hold the RFID tag up to the RFID reader. The corresponding information is output. Recommendation for use: The data that are output can be adjusted in advance in consultation with ads-tec to meet customer requirements . © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 39: Drives
Data loss might result in the event of non-compliance! © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 40: Software & Driver Installation
Install Windows and set up the basic data. With devices including touch screens, the touch screen driver as well as the soft keyboard should be installed in order to ensure their full functionality. © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 41: Maintenance
Earth Secure connection and According to VDE0113 connections correct operation 11.2 Information on storage Always observe the environmental conditions for storing batteries (no direct sun light, dry room, no frost,…). © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 42: Technical Details
*The figures given for the typ. current consumption do not take into consideration any peripherals connected to the Universal Serial Bus (USB) interfaces. ** The UL marking applies for operating temperatures up to max. 40°C, 24V DC power supply and for devices without heater. © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 43: Service & Support
In this case, maintenance and support is provided by the partner company.