Makita PLANER JOINTER 2004 Instruction Manual
Makita PLANER JOINTER 2004 Instruction Manual

Makita PLANER JOINTER 2004 Instruction Manual

132 mm (5 1/4") planer jointer

Advertisement

132
mm
(5%") MODEL
2004
NO.
MODEL
2 0 0 4
No, of
knives
Two on
each feed
INSTRUCTION MANUAL
width
-
c z k g
Feed ratelmin.
Table size fW
x
L )
Fence size
depth
-
120"
x 410"
Auto feed
9.7m 131'8ft')
(4.3/4")~(15.3/4")
132"
3mm
~
Manual
f5-1/4")
f118")
Rabbet depth
l2Omm x
8OOmm
500"
x 70"
infeed
6mm
1114"l
1 4 4 4 " ) x
131-1/2"1
119-5/8")
x
(2-3/4")
No load
Overall dimensions
Power
Continuour rating,
Input
Output
speed
fWx L x
HI
ws"$),
SUPPk
cord
8.500
800mm
x
423"
x
592"
4 2
kg
2.5m
'''0°
697
R/min.
131.1/2")
X
(16-5/8")
x
123.5/16')
(92.6 lbsl
18.2
f t . )

Advertisement

Table of Contents
loading

Summary of Contents for Makita PLANER JOINTER 2004

  • Page 1 INSTRUCTION MANUAL MODEL width Auto feed 132" 2 0 0 4 Manual f5-1/4") infeed Continuour rating, No, of knives Input Output Two on '''0° each feed (5%") MODEL 2004 c z k g Feed ratelmin. Table size fW depth 120" 9.7m 131'8ft') (4.3/4")~(15.3/4") f118")
  • Page 2 GENERAL POWER TOOL SAFETY RULES GENERAL SAFETY PRECAUTIONS KEEP GUARDS IN PLACE and in working order. 2. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to that keys and adjusting wrenches are removed from tool before turning KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents. 4.
  • Page 3 PRE LlMl NAR Y NSTR UCTl ONS Your electric tool i s precision built and manufactured to satisfy the highest standards. For maximum performance, tool life, and your safety, follow these instructions carefully. long VOLTAGE WARNING: Before connecting the tool t o sure the voltage supplied i s the same as that specified on the nameplate of the tool.
  • Page 5 Special Precautions with Planer- Jointer Jointing Operations Do not perform jointing operations on material shorter than narrower than inch b. Planing Operations Do not perform planing operations on material shorter than narrower than inch 5-1/4 (132 inches mm) in manual infeed or thinner than Maintain the proper relationships of infeed and outfeed table surfaces and cutter head knife path.
  • Page 6 Return Cut stock can be easily returned by means of the rollers on top. Support long stock a t the beginning and end of a cut to prevent gouging or rough end sur- faces. 1 . The depth of cut i s indicated in mm on the scale.
  • Page 7 Cutter Replacement First, unplug the planer-jointer from the power source. Removal Auto infeed table (Planer): First, left off the chip cover (guard). Manual feed table (Jointer): Remove cover (guard) after taking off safety cover Planer (guard) bolt. Jointer...
  • Page 8 2. Installation Hold the belt steady by hand and insert the cutter between the leaf spring and the drum so that the blade protrudes slightly above the table surface. Cutter Height Adjustment Make the drum stationary before per- forming the adjustment drum locking lever from the stopper;...
  • Page 9 After hooking the lever for drum locking onto the stopper, secure the hex bolts hold- ing down the blade holder: a total of 8 on the planer arid jointer sides, respectively. After all bolts have been secured, check your cutter height agian.
  • Page 10 To replace carbon brushes, use the screwdriver equipped to remove cap on the motor housing. Then replace the brush. HOW T O USE T H E SHARPENING HOLDER First, loosen the 2 wing nuts on the holder and insert blades Aand B as in figure that they contact side C and D.
  • Page 11 (mm) Width Pait 731013-7 136 15-3/8"1 136 (5-3/8'1 731203-2 . . . Material Tungsten-Carbide Dressing stone No. 741801-4 Part 155334-7 Part Sharpening holder 123006.2 Part Socket wrench 782203-5 Part...
  • Page 12 132mm(5%") PLANER JOINTER Model 2004...
  • Page 14 P H. Screw M5x16 IWilh Washer1 Torsion Spring 13 Sleeve Washer 6 Sleeve 8011 ~ 6 x 1 7 Drum Cover 135 Blade Holder Planer Blade 136 Gear 15 Helical Ball 6203LLB Bearing Washer 17 Drum P H Screw M4x8...
  • Page 15 250 V Fan 92 141025.7 O"llSs.l L13051-6 Ball Bearing 111066-7 ~31270-2 CDmDr&On Rubber Rn 4 1630024 301002-1 Insulation Washer Carbon Brush CB-150 5431504 For 1 W V . 643153.8 CB-153 6436504 Holder RuMar Pin 6 263005-3 FIELD ASSEMBLY (With Garter Spring 654020-2) 5233W.6 115 V.
  • Page 16 &24?c&k-*ud. Anjo, Aichi, h p 8 n PRINTED IN JAPAN 1979-9-1.000...

This manual is also suitable for:

2004

Table of Contents