Using The Sub Receiver - ELECRAFT K3 Owner's Manual

Using the Sub Receiver

The KRX3 option adds an independent, high-
performance sub receiver to the K3. It allows you
to monitor a second frequency, using different
bandwidths or modes. Diversity receive is possible
if the main and sub receivers use different antennas.
Dedicated Sub Receiver Controls
Tapping turns on the sub receiver (and
S U B
icon). VFO B then controls the sub's frequency, and
also serves as the TX frequency during SPLIT.
You should leave the sub off when not in use.
This turns off the -3 dB passive splitter used when
the sub shares the main receiver's antenna path.
Holding links the VFOs (whether the sub
S U B
receiver is on or off). The kHz decimal point of
VFO B flashes as a reminder. VFO A is the master,
moving both VFOs in tandem.
Holding for 2 seconds or longer turns on
S U B
diversity receive (pg. 38). The kHz decimal point of
VFO A flashes as a reminder. VFO A controls both
the main and sub frequencies in diversity receive,
but VFO B remains independent so it can be used as
the SPLIT transmit frequency.
SUB AF gain normally sets the sub's volume
SUB AF can be used as a
level. Alternatively,
main/sub balance control (see
).
AF With stereo headphones or dual speakers,
you'll normally hear main on the left and sub on the
right. CONFIG:L-MIX-R selects various alternate
combinations of main/sub audio mixing.
CONFIG:SPKRS must be set to
stereo speakers; otherwise, set it to
SUB RF gain normally sets the sub receiver's
RF GAIN level. If this knob is assigned to main/sub
squelch (CONFIG:SQ MAIN), then RF gain for
main/sub is controlled by the main RF gain control.
BSET: Additional Sub Receiver Settings
Normally, receive controls apply only to the main
receiver. This includes SHIFT, WIDTH,
, etc., as well as
A T T N
settings for the sub receiver, first hold
A will show , and the S-meter will show the
B SE T
sub receiver's signal level. After you've made the
desired sub receiver changes, tap
to exit .
B SE T
B S E T
CONFIG:SUB
if you use
2
.
1
P R E
. To change these
M O D E
. VFO
B S E T
or hold
A / B
The sub receiver's band cannot be set
independently unless
to
YES
when you tap
receiver band will always be set the same as
main.
Sub Receiver Antenna Selection
The sub receiver gets its RF input either from the
SU B
main receiver (sharing ANT 1-2 or RX ANT IN), or
from its auxiliary antenna input (see pg. 41).
When using
sub between
AUX input). When
icons show which antenna the sub is sharing
R X
with the main receiver. When
these icons will all be off (if CONFIG:KRX3 is set
for
A N T =B N C
ATU antenna,
A N T =A TU
Shortcut: If you're not in
quickly switch the sub between
holding
ANT on/off for the main path.)
The sub receiver's AUX antenna must be
well-isolated from the transmit antenna to avoid
activating the sub's carrier-operated relay.
Using the AUX input for the sub receiver
slightly improves sensitivity of both the main and
sub receivers because the splitter is not used.
Sub Receiver Band Independence
If CONFIG:VFO IND is set to
the sub receiver to a different band from main.
Hold
B S E T
sub receiver's band. If you only use band-
independence for the sub occasionally, you may
want to assign VFO IND to a programmable
function switch (pg. 21).
If the two receivers are sharing the main
antenna path, putting the sub receiver on a
, higher-frequency band than main may result in
signal loss in the sub. This is due to sharing of the
main receiver's low-pass filters. If you select an
incompatible band combination, the K3 briefly
displays
receiver signal loss, use the sub's AUX input.
37
CONFIG:VFO IND
. If it's set to , you'll see
N O
during
B A N D
, you can tap
B SE T
(shared) and
MA I N
is in effect, the
MA I N
A U X
) or will show the non-transmit
or (if KRX3 is set for
1 2
).
B SE T
. (Tapping
R X A N T R X A N T
, then tap up/down to select the
B A N D
as a warning. To avoid sub
U SE A U X
is set
=MA IN
, and the sub
B SE T
to switch the
A N T
(the sub's
A U X
- and
1 2
is in effect,
mode, you can
and by
MA I N A U X
turns RX
, you can set
YES