Table of Contents
Advertisement
Owner's Manual
The "Input" button is used to select an external digital
source by sequentially scrolling through four (4) digital
inputs: D1 uses an XLR connector for an AES/EBU digital
signal; D2 uses an RCA connector for a S/PDIF digital
signal; D3 uses a TosLink connector for an optical digital
signal and D4 uses a USB type B connector for use with
a computer equipped with a USB port and music player
software such as iTunes or Winamp. Note: you cannot
connect a USB flash drive or external hard drive to the
"D4" input. The display window will show "D1
"D2 SPDIF", "D3 TOS" and "D4 USB", depending on the
input selected; Four dashes "----" will replace the input
type after approximately 2 seconds. These dashes
indicate that the 650D is in the process of locking onto
an external digital signal – this may take several
seconds. Once the 650D successfully locks onto the
digital signal, the four dashes will be replaced by the
sampling rate of this digital signal. When the signal
cannot be locked onto, "----" remains in the display
window. The MOON 650D is capable of processing an
external digital input signal at one of the following six
(6) different sampling rates: 44.1kHz, 48.0 kHz, 88.2kHz,
96 kHz, 176.4kHz and 192kHz.
The "Random" button, when pressed, will play each of
the tracks on a compact disc in a completely random
order, as opposed to the sequential order as they
appear on the disc.
If you have already created a
program of selected tracks, it will play these
programmed tracks in a random order. The LED located
immediately to the left of the "Random" button will
illuminate when you've engaged the random mode.
The "Time" button allows you to scroll through the four
(4) different display modes for time related information.
Each time you press the "Time" button, the system
scrolls to the next time information mode. By default,
the 650D will display the elapsed time of the track
currently playing. The scrolling order is as follows: (i)
Elapsed time of the current track. (ii) Remaining time of the
current track (iii) Elapsed time of the entire compact disc (or
programmed tracks) (iv) Remaining time of the entire compact
disc (or programmed tracks).
If you want to turn the display off, press and hold the
"Display" button for 3 seconds. When the display is
turned off, it will still come back on for a short period of
time whenever you press any of the buttons located on
the front panel or the remote control, using the
brightness level that was previously established; the
display will automatically turn off again once you are
done. To turn the display back on, simply press and hold
the "Display" button for 3 seconds. Finally, the display
mode that you select will continue to be used until you
either select another mode or power down the 650D
using the main power switch located on the rear panel.
To load a compact disc into the 650D, press
AES",
the drawer. While the drawer is opening, the word
"OPENING" will appear in the display window, followed
by "OPEN" when the drawer is fully open. Place the CD
in the drawer with the label side facing up. To close the
drawer, press
display window followed by "LOADING" once the
drawer is closed. "LOADING" indicates that the 650D is
reading the CD's table of contents. Once the CD is
successfully read, the total number of tracks and total
playing time will appear in the display window. As a
result of various copy protection schemes, some CDs
will take longer to read than others. When you load an
incompatible CD (i.e. data only, SACD, DVD-A or DVD-
Video), the word 'BAD DISC' will appear in the display
window and the drawer will automatically open to eject
this CD.
Finally, if you inadvertently leave the drawer open,
it will automatically close after approximately three
(3) minutes.
Press
to begin playing a compact disc. Pressing
while a track is already playing will result in the current
track immediately playing again, starting from the
beginning. Press
forward through the compact disc's tracks.
you've located the track number, press
playing that track.
backward track change while a disc is already playing, it
will automatically start playing the track you select; you
need not press
Press
to pause the compact disc currently playing.
The disc will continue spinning and the laser will be
suspended in its current position. Press
time or
the compact disc from playing. The laser will return to
the start position of the disc.
again; "CLOSING" will appear in the
to search backward or
When you initiate a forward or
.
to resume playing the disc. Press
to open
to search
When
to begin
a second
to stop
9
Advertisement
Table of Contents
