Vermont Castings VWDV70NTSCSB Installation And Operating Instructions Manual page 42

VWDV70 Series Gas Fireplace
1. Press the ON/up button to turn
on the fi replace. The fl ame icon
on the LCD displays High.
2. Press the OFF/down button to
decrease the fl ame height and
turn off the fi replace. When the
OFF/down button is pressed
for three times, the fl ame icon
changes from High to Medium,
to Low, then to Off.
3. If the OFF button is held for
more than 3 seconds at any
fl ame height, the fi replace will
be turned off and the fl ame icon
disappears.
4. Sliding up and down on the arrow buttons can also
turn on or turn off the fi replace.
5. If the fi replace is shut off using the above methods in 3
and 4, all the settings will be remembered and will be
resumed next time the fi replace is turned on (Memory
Off).
Timer Mode
Figure 66
Press the TIMER button to enter timer mode. The fi re-
place will stay on for a period of time as specifi ed by the
timer and then be shut off by the transmitter when the
timer counts down to zero.
1. When the TIMER button is pressed, the Set Time ap-
pears in the frame of the button and fl ashes.
2. Use ON/up and OFF/down to
increase or decrease the Set
Time in 15 min. increments, be-
tween 0:00 to 6:00. Sliding up
and down on the arrow buttons
will increase or decrease the Set
Time in 1 hour increments.
3. Push the TIMER button again to
confi rm the Set Time, the trans-
mitter sends an ON signal to
turn on the fi replace.
4. The fl ashing stops and the ON/
up and OFF/down buttons be-
come fl ame height controller
again. The fl ame height will then
stay as set up by the ON/up and
OFF/down buttons.
5. The TIMER button can be used when the transmitter
is in Manual Mode or in Thermostat Mode. In both
modes, the fi replace will be shut down completely
when the timer counts down to zero.
6. To exit Timer Mode,
a. Push and hold the TIMER button for 3 seconds Or
42
TOUCH SCREEN REMOTE CONTROL OPERATION
Figure 65
Figure 66
b. Use the OFF/down buttons to decrease the Set
Time to zero Or
c. Slide down on the arrow buttons to exit TIMER
mode and shut off the fi replace.
Thermostat Mode
Figure 67
NOTE: The Command Center buttons will disable when
thermostat is being used.
Press the THERMO button to set the transmitter in ther-
mostat mode. The transmitter will automatically turn on
the fi replace when the room temperature is below the set
temperature and turn off the appliance when the room
temperature is above the set tem-
perature within one degree.
1. When the THERMO button is
pressed, the Set temperature
appears in the frame of the but-
ton and fl ashes.
2. Use ON/up and OFF/down to
increase or decrease the Set
temperature in 1 degree incre-
ments, between 45 degrees
and 90 degrees. Slide up and
down on the arrow buttons will
increase or decrease the Set
Temperature in 10 degrees in-
crements.
3. Press the THERMO button
again to confi rm the Set Tem-
perature. The transmitter will send out an On signal or
an Off signal depending on the relationship between
the Set temperature and the Room temperature.
4. The fl ashing stops and the ON/up and OFF/down but-
tons become fl ame height controller again. The fl ame
height will then stay as set up by the ON/up and OFF/
down buttons.
5. To exit Thermostat Mode:
a. push and hold the THERMO buttons for 3 sec-
onds or
b. slide down on the arrow buttons to exit Thermo-
stat mode and shut off the fi replace.
®
Smart Mode Option for Thermostat Mode
Figure 68
Press and hold the THERMO button and the ON/UP but-
ton at the same time for 3 seconds to toggle between
Smart Mode and the regular Thermostat Mode. The icon
"Smart Mode" will appear under the Set Temperature.
The transmitter will automatically adjust the fl ame height
according to the difference between the Set temperature
and the Room temperature. There is no manual fl ame
height adjustment. The fan speed will also automatically
adjust if turned on.
Figure 67
20306745