Model Copy; Model Name - FUTABA 8J Instruction Manual

GOAL of EXAMPLE:
Copy model 3 into model 5.
N O T E : T h i s i s o n e o f s e v e r a l
functions for which the radio requires
FRQ¿UPDWLRQ WR PDNH D FKDQJH
Where next?
*Radio will show "complete" and it shows that the copy was completed. Note that if the power switch is turned off prior to completion, the data will
not be copied.
)LUVW LW LV LPSRUWDQW WR FOHDU RXW DQ\ ROG VHWWLQJV LQ WKH PHPRU\ IURP SULRU XVH XVLQJ WKH MODEL RESET .
MODEL RESET FRPSOHWHO\ UHVHWV DOO GDWD LQ WKH LQGLYLGXDO PRGHO \RX KDYH FXUUHQWO\ VHOHFWHG 'RQ W ZRUU\  WKHUH LV QR ZD\
you can accidentally delete all models in your radio with this function. Only a service center can completely reset your
UDGLR V HQWLUH PHPRU\ DW RQFH 7R GHOHWH HDFK PRGHO LQ \RXU UDGLR V PHPRU\ IRU H[DPSOH ZKHQ VHOOLQJ  \RX PXVW SELECT
each model, reset that memory, then go SELECT the next memory, etc.
Note that when you COPY RQH PRGHO PHPRU\ LQWR DQRWKHU RU FKDQJH WKH PRGHO V W\SH \RX QHHG QRW GHOHWH DOO H[LVWLQJ GDWD
¿UVW E\ XVLQJ WKLV IXQFWLRQ COPY completely overwrites anything in the existing model memory, including MODEL NAME .
The MODEL TYPE function overwrites all data except name and RX MODUL .
GOAL of EXAMPLE:
Reset model memory 1.
N O T E : T h i s i s o n e o f s e v e r a l
functions for which the radio requires
FRQ¿UPDWLRQ WR PDNH D FKDQJH
Where next?
*Radio will show a "complete" and it shows that the reset was completed. Note that if the power switch is turned off prior to completion, the data will
not be reset.
STEPS:
Open the menu, then open MODEL
SELECT submenu.
Confirm you are currently using the
proper model memory. (Ex: 3)
Go to MODEL COPY and choose the
model to copy into. (Ex: 5)
&RQ¿UP \RXU FKDQJH
Close.
SELECT the copy you just made: see p. 27.
Rename it (it is currently named exactly the same as the model copied): see p. 29.
STEPS:
Confirm you are currently using the
proper model memory. (Ex: 1)
Open the menu, then open MODEL
SELECT submenu.
G o t o MODEL RESET a n d r e s e t t h e
memory.
&RQ¿UP WKH FKDQJH
Close.
Now that the memory is reset, name has returned to the default (Ex:
MODEL-0001 ).
NAME the model: p. 29.
COPY a different model into this memory: p. 27.
SELECT a different model to edit or delete: p. 27.
Change the MODEL TYPE to airplane or helicopter: see p. 30.
Change the receiver modulation [ SFHSS or FHSS ]: see p. 31.
Utilize servo REVERSE : see p. 35.
Adjust servo travel with END POINT : see p. 36.
Set up dual/triple rates and exponential ( D/R , EXP ): see p. 39.
28
INPUTS:
for 1 second.
if required to MODEL SELECT .
If SELECT does not indicate 3 , use MODEL
SELECT , p. 27.
to COPY . to 5 .
for 1 second.
Sure? displays. *
INPUTS:
2Q KRPH VFUHHQ FKHFN PRGHO QDPH DQG
number on top left. If it is not correct,
use MODEL SELECT .
for 1 second.
if required to MODEL SELECT .
to RESET . for 1 second.
Sure? displays. *