Additional Operation Features - Braeburn 2100 User Manual

4
PROGRAMMING
Setting Your Energy Saving Programs–Tips Before Starting
4.4
• It is important for you to set the current time of day (note the AM/PM indicator in the display),
and the current day of week correctly to avoid problems with program execution. This must be
done prior to entering any program settings.
• The heating and cooling programs have both separate setpoint times and setpoint temperatures.
• This thermostat is pre-programmed with weekday and weekend setpoint times and temperatures
recommended by the Environmental Protection Agency and the U.S. Department of Energy
in their ENERGY STAR ® program. These settings provide efficient energy savings during normal
heating and cooling modes of operation. If you desire to use the setting in the table, no
further programming is necessary. Review these time and temperature settings prior to
establishing your personal program settings to maximize your savings, and minimize
programming requirements.
Time: 6:00 am
Heat: 70˚ F (21˚ C)
Cool: 75˚ F (24˚ C)
Time: 8:00 am
Heat: 62˚ F (17˚ C)
Cool: 83˚ F (28˚ C)
Time: 6:00 pm
Heat: 70˚ F (21˚ C)
Cool: 75˚ F (24˚ C)
Time: 10:00 pm
Heat: 62˚ F (17˚ C)
Cool: 78˚ F (26˚ C)
• Make sure you place the system switch in the HEAT or COOL modes of operation as appropriate.
You should not enter a program in the OFF position.
• When you place the system switch in the COOL or HEAT modes of operation, the appropriate
indicator will also appear in the LCD display when the system is running.
• When you place the system switch in the OFF mode the display will indicate OFF.
Programming Overview
4.4.1
Your thermostat contains separate Weekday and Weekend Program Groups that allow you to
change the daily setpoint times and temperatures to meet your individual schedule needs.
Weekday - allows you to program all the weekdays (M, TU, W, TH, F will show in display) at the
same time. Allows programming times and temperature settings for four setpoints (MORN,
DAY, EVE & NIGHT) to meet your weekday schedule needs.
Weekend - allows you to program all the weekend days (SA, SU will show in the display) at the
same time. Again allows programming times and temperature settings for four setpoints
(MORN, DAY, EVE & NIGHT) to meet your weekend schedule needs.
Entering Your Program
4.4.2
1. Place the system switch in the HEAT mode of operation.
2. Press the PROG button to enter Program
setting mode. The MORN setpoint of the Weekday
Program Group will be displayed. The display
will show M, TU, W, TH, F to indicate the
Weekday group is being programmed. The
hour portion of the setpoint time and the
AM/PM indicator will be flashing.
cont.
Time: 6:00 am
Heat: 70˚ F (21˚ C)
Cool: 75˚ F (24˚ C)
Time: 8:00 am
Heat: 70˚ F (21˚ C)
Cool: 75˚ F (24˚ C)
Time: 6:00 pm
Heat: 70˚ F (21˚ C)
Cool: 75˚ F (24˚ C)
Time: 10:00 pm
Heat: 62˚ F (17˚ C)
Cool: 78˚ F (26˚ C)
6
4
PROGRAMMING
Setting Your Energy Saving Programs
4.4
Entering Your Program
4.4.2
3. Press the or button to change the time to the desired hour in 1 hour increments,
press the PROG button to save. The minute portion of the setpoint time will begin flashing.
4. Press the or button to change the time to the desired minute in 10-minute increments,
press the PROG button to save. The SET TEMP will begin flashing.
5. Press the or button to change the setpoint temperature to the desired setting in 1˚ F
increments (0.5˚ C), press the PROG button to save. The thermostat will now display the
DAY setpoint time and temperature. Again, you will see the hour portion of the setpoint time
and the AM/PM indicator will be flashing.
6. Follow steps 3 through 5 to set the setpoint times and temperatures for the MORN, DAY,
EVE and NIGHT setpoints for the Weekday group in the HEAT mode.
7. After pressing the PROG button, you will enter the Weekend Program Group. The display
will show SA, SU to indicate the Weekend group is being programmed. The hour portion
of the MORN setpoint time and the AM/PM indicator will be flashing.
8. Follow steps 3 through 5 to set the setpoint times and temperatures for the MORN, DAY,
EVE and NIGHT setpoints for the Weekend group in the HEAT mode.
9. Place the system switch in the COOL mode of operation. The display will show COOL. Follow
steps 2 through 8 to program the setpoint times and temperatures for the Weekday and
Weekend groups in the COOL mode.
NOTE:
To erase all entered programs, current time of day, day of week and other user
settings, gently press the RESET button using a paper clip or a small pencil tip. This will
return all thermostat settings to their default values.
ADDITIONAL
5
OPERATION FEATURES
Review Set Temperature
5.1
1. Press and hold
or button. The current setpoint temperature will be displayed in the
place of the current room temperature, and the indicator SET TEMP will be displayed.
2. The display will return to normal operating mode when
the or button is released. Continuing to hold
the or button for 3 seconds or longer will allow the
user to temporarily override the current programmed
setpoint (See Temporary Program Override).
Temporary Program Override
5.2
1. Press and hold the
or button for 3 seconds. The entire display will flash once and the
SET TEMP indicator will be displayed. Release the
button again as desired to adjust the set temperature.
2. The display will return to normal operating mode after
15 seconds or you can press the RETURN button.
3. The program indicator (MORN, DAY, EVE OR NIGHT) will
be flashing in the display, indicating that a Temporary
Program Override is in effect. The Temporary Program
Override will reset when the next setpoint time occurs or
after 4 hours–whichever comes first.
cont.
cont.
cont.
or button and press the
7
or