Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
QUICK START GUIDE
FEATURES
• 1/3" 3.0 Megapixel Progressive Scan CMOS image sensor
• Up to 30fps live view @ 1920x1080 (2MP) / 15fps live
view @ 2048x1536 (3MP)
• 2.8~12mm Varifocal Lens (VTC-TNB36R3V) / 3.6mm
Fixed Iris Lens (VTC-TNB42R3F)
• 42 Infrared LED's with 150' IR Range (VTC-TNB42R3F) /
36 Infrared LED's with 120' IR Range (VTC-TNB36R3V)
• Wide Dynamic Range (WDR)
• True Mechanical Day/Night function by ICR
• 3D-DNR Noise Reduction
• On Board Motion Detection
• H.264/MJPEG Dual Streaming
• Onvif Compliance
• Remote Viewing via CMS, Web Browser, and iOS & Android
Apps
• Minimal Latency with up to 10 simultaneous user
connections
• IP66 Weather Resistance
• 12VDC & PoE (Power over Ethernet) Operation
*Refer to included CD for complete detailed User's Manual.
VTC-TNB42R3F
VTC-TNB36R3V
3.0 Megapixel Indoor/Outdoor
WDR IP IR Bullet Cameras
Advertisement
Table of Contents
Related Manuals for Vitek VTC-TNB42R3F
Summary of Contents for Vitek VTC-TNB42R3F
-
Page 1: Quick Start Guide
@ 2048x1536 (3MP) • 2.8~12mm Varifocal Lens (VTC-TNB36R3V) / 3.6mm Fixed Iris Lens (VTC-TNB42R3F) • 42 Infrared LED’s with 150’ IR Range (VTC-TNB42R3F) / 36 Infrared LED’s with 120’ IR Range (VTC-TNB36R3V) • Wide Dynamic Range (WDR) • True Mechanical Day/Night function by ICR •... -
Page 2: Components And Accessories
Components and Accessories Camera Drill Template Quick Guide Product Manual CD Screws Waterproof Cap Overview This camera series supports both fixed and varifocal lenses. Please note that the zoom and focus features mentioned below are only available on the varifocal lens version. Lens Power Cable Lens Cover... - Page 3 Network Cable & Power Connections First connect the Waterproof Cap to an Ethernet patch cable, then connect the cameras ethernet adaptor. If not powering the camera with PoE, also connect the power Cable to an approved 12VDC Power Supply. 12VDC Optional 12VDC Power Connection.
-
Page 4: Installation
Installation Before start, please make sure that the wall or ceiling is strong enough to withstand 3 times the weight of the camera. The mounting steps are as follows: 1. Attach the drill template to the place where you want to install the camera, then drill 3 screw holes and 1 cable hole (if you want to route the... - Page 5 Installation 3. Loosen the mount lock to adjust the Pan and Tilt of the camera, then tighten the mount lock to secure the viewing angle adjustments. 360° Pan 90° Tilt 4. To adjust the lens, start by removing the Lens Cover, then adjust the Focus and Zoom levers to achieve a clear image.
-
Page 6: Lan Configuration
LAN Configuration The camera can be accessed on the local network either using the IP-Tool or directly in a web browser. 1. Attach the drill template to the place where you want to install the camera, then drill 3 screw holes and 1 cable hole (if you want to route the cables through the mounting base) according to the drill template Accessing the Camera Using the IP-Tool... - Page 7 4. Double-click the IP address and then the system will pop up the web browser to connect IP-CAM . IE browser will download the Active X control automatically. After downloading, a login window will pop up as shown below: Input the user name and password to log in. Default user name: admin / Default password: 123456.
-
Page 8: Wan Configuration
2. Open the IE Browser and input the default address of IP-CAM and confirm. The IE browser will download Active X control automatical- 3. After downloading Active X control, the login dialog box will pop up. 4. Input the default username and password and then enter to view. WAN Configuration Access the camera by the router or virtual server for example.