Related Manuals for Viking VS 3725
Summary of Contents for Viking VS 3725
- Page 1 FEBERARY/06/2006 VS 3725 2-WAY LCD PAGER ALARM WITH REMOTE ENGINE STARTER Installation Manual MEGATRONIX VAN NUYS, CA U.S.A. VS3725IN...
-
Page 2: Installer Warnings
FEBERARY/06/2006 INTRODUCTION INSTALLER WARNINGS This Remote Starter with Alarm System is designed to be installed on fuel injected vehicles with an automatic transmission ONLY. Never install this remote starter on a manual transmission vehicle. This system must be installed and wired through a safety switch it will not start in any forward or reverse gear. -
Page 3: Installation Diagram
FEBERARY/06/2006 INSTALLATION DIAGRAM 5. Brown: Positive Output to Siren 4. Black: Ground to Vehicle Frame Two Way Transceiver Antenna 3. White: Parking Light Relay Output 10A Fuse 2. Red / White: Parking Light Power Input 3A Fuse 1. Red: +12V Input 4 Pin 9 Pin 1. - Page 4 FEBERARY/06/2006 14 PIN WHITE MINI CONNECTOR: 1. W h ite / V io le t W ire : ( ) P os itiv e S afety S h ut D o w n In p u t fo r B rak e s w itc h. 2.
- Page 5 FEBERARY/06/2006 NOTE: This wire must be connected to the vehicle side of the starter cut relay (when used). For the electrical neutral switch configuration, this connection must be made between the starter inhibit relay (when used) and the neutral safety switch as shown in the following diagram. Failure to connect this wire to the ignition switch side of the neutral safety switch can result in personal injury and property damage.
- Page 6 FEBERARY/06/2006 This wire is the ground trigger input wire for negative door pin switch. This wire is connection for "grounding" type factory door pins locate the "common wire" that connects the door pin switches. Make the connection of the GREEN Wire here. Violet wire –...
- Page 7 FEBERARY/06/2006 – (-) Neutral Safety Switch Input – When the BLACK/WHITE wire is grounded, the remote start unit is operable. When this wire is open from ground, the remote start is disable. 1. The optional “remote start toggle switch” can be added on to temporarily disable the Remote Start Device, it can prevent the vehicle from being remote started accidentally.
- Page 8 FEBERARY/06/2006 Ignition 3 output: + 12 V Constant Some newer vehicles use a third ignition wire Fused 25A Capable which is required to start and keep the vehicle’s Yellow Wire engine running. If this is the case, wire an IGN 3 relay (not supplied) as shown below: Ignition 3 Wire From Do not connect any vehicle circuits together, they...
- Page 9 FEBERARY/06/2006 This output is programmable. If programmed rearm a factory installed security system. This wire will supply a pulse whenever the remote start times out or is shut dowm using the transmitter and remote door locking.. White wire – (-) 200mA Dome Light Control Output – This wire becomes grounded when the dome light controls circuit active.
- Page 10 FEBERARY/06/2006 3 PIN DOOR LOCK CONNECTOR: INSTALL NEW DOOR LOCK MOTOR Blue Wire ( - ) Unlock Pulse Blue Wire (+) Lock Pulse ( - ) Lock Pulse +12V Green Wire ( + ) Unlock Pulse 3 Pin Plug To Alarm Green Wire NEGATIVE TRIGGER DOOR LOCK SYSTE...
- Page 11 FEBERARY/06/2006 2 STEP DOOR UNLOCK WIRE CONNECTION FOR 2 STEP DOOR UNLOCK WIRE CONNECTION FOR GROUND SWITCHED DOOR LOCKS POSITIVE SWITCHED DOOR LOCKS +12V 14-Pin OEM Door Master Lock Switch OEM Door Master Lock Switch 14-Pin Plug Pink Wire From Plug From Pink Wire...
- Page 12 FEBERARY/06/2006 Eight times Pink Wire = Pink Wire = Factory Pink Wire = Start Two step door Security Disarm Status Output unlock output Signal Output Nine times Black / Green Wire Black / Green Wire Black / Green Wire Black / Green Wire Channel 4 Output = Channel 4 Channel 4...
- Page 13 FEBERARY/06/2006 5. Finish by turning the ignition switch to “On” position. REMOTE START FEATURE PROGRAM MODE. 1. Turn the Ignition switch ‘On then Off 3 TIMES and stay in Off position. 2. Within 10 seconds, push and release the Valet switch 6 times and holding in on the 6 push until two long chirp from siren to confirm you are now in the start feature programming mode.
-
Page 14: Return To Factory Default Setting
FEBERARY/06/2006 4. Within 10 seconds, press and release button on the transmitter, one chirp to confirm the system in features “RPM Learning mode”. 5. Within 10 seconds, start the vehicle with the key. (While the engine is running, the parking light & LED will flash, If don’t, please check tach. -
Page 15: Mechanical Neutral Safety Switch Considerations
FEBERARY/06/2006 b. If the starter engages, immediately step on the brake pedal to shut down the system, recheck your VIOLET wire (starter output wire) connection. The heavy gauge VIOLET wire must be connected to the ignition switch side of the Neutral Start Switch. If the vehicle you are working on does not have an Electrical Neutral Safety Switch, it will be necessary to reconfigure the Remote Starts Wiring to accommodate this vehicle. - Page 16 FEBERARY/06/2006 METHOD 1 Ignition Key In Sensor Drivers Door Pin Switch Switch Closes with Key In Ignition Cylinder Key In Chime Module + 12 V Connected to (-) Negative 1N4003 To Hood Pin Switch Safety Input Wire Safety Shut Down White/ Black To connect to the key in sensor as shown in method 1: A.