Table of Contents
Advertisement
14 PIN WHITE MINI CONNECTOR:
1. W h ite / V io le t W ire : (
2. B lac k/W h ite W ire : (
3 . W h ite / B lu e W ire : (
4 . W h ite / B la c k W ire : (
5 . W h ite / R ed W ire : T a c h. S ig n a l Inp ut
6 . Y e llo w W ire : (
7 . B la c k / V io le t W ire : (
8 . B ro w n / W h ite W ire : (
9 . W h ite W ire : (
1 0 . B la c k / R e d W ire : (
1 1 . B la c k / G ree n W ire: (
1 2 . G ray W ire : (
1 3 . P in k W ire: (
1 4 . O ran g e / W h ite W ire : (
IM P O R T A N T N O T E : D ire c tly c o n ne c t th e B L A C K /W H IT E w ire to the "G R O U N D " w he n this w ire is n ot
us e d.
Keep wiring away from moving engine parts, exhaust pipes and high-tension cable. Tape wires that pass
through holes on the firewall to prevent fraying. Watches out sharp edges that may damage wires and
causes short circuit.
CAUTION: Do not connect the wire harness to the control module until all wiring to vehicle is complete.
6 PIN HEAVY GAUGE WIRING CONNECTIONS:
Remember that the system does to start a vehicle is duplicate the functions of the ignition key switch!
Below, we will explain the three basic functions of the ignition switch. Since this installation will require
analysis of the ignition switch functions, we recommend making the three connections below at the ignition
switch harness directly.
Violet wire – Starter Output –
Careful consideration for the connection of this wire must be made to prevent the vehicle from starting
while in gear. Understanding the difference between a mechanical and an electrical Neutral Start Switch
will allow you to properly identify the circuit and select the correct installation method. In addition you will
realize why the connection of the safety wire is required for all mechanical switch configurations.
Failure to make this connection properly can result in personal injury and property damage.
In all installations it is the responsibility of the installing technician to test the remote start unit and assure
that the vehicle can not start via RF control in any gear selection other than park or neutral.
In both mechanical and electrical neutral start switch configurations; the connection of the VIOLET wire
will be made to the low current start solenoid wire of the ignition switch harness. This wire has +12 volts
when the ignition switch is turned to the "START" (CRANK) position only. This wire have 0 volts in all other
ignition switch positions.
VS3725IN
+
) P os itiv e S afety S h ut D o w n In p u t fo r B rak e s w itc h.
-
) N e utra l S a fe ty S w itc h In p ut &
-
(
) R e m o te S tart T o gg le S w itc h In p ut
-
) In s tan t S ta rt a nd T u rn O ff In pu t
-
) N e ga tiv e S a fety S h ut D o w n In pu t fo r H o o d p in s w itc h
-
) 2 0 0m A Ign itio n 3 C o n trol O u tpu t
-
)2 0 0 m A C h an n e l 6 P ro gra m m a b le O u tp ut
-
) 2 0 0 m A P ro g ram m ab le O u tp ut
1 . H o rn O u tp u t (F ac to ry D e fa ult S ettin g ) or
2 . F ac to ry S ec u rity R e a rm S ig na l O utp ut
-
) 2 0 0m A D o m e L igh t C on tro l O u tpu t
-
) 2 00 m A C h an n e l 5 P rog ra m m a b le
-
) 2 0 0 m A P ro gra m m a b le O utp ut
1. C h an n e l 4 P rog ram m ab le O u tp ut (F ac to ry D e fau lt S e ttin g) or
2 . . G ro un d O utp ut D u rin g S tart (C ra n k )
-
) 2 0 0 m A C ha n n el 3 (T run k )
-
) 2 00 m A P ro gra m m a b le O u tp ut
1 . 2 S tep s D o or U nlo c k O u tp ut (F ac to ry D e fa ult S e tting ) or
2 . F a c tory S ec u rity D is a rm S ig n a l O utp u t o r
3. S ta rt S ta tu s (S h o c k S e ns o r B y -P a s s C on tro l) O utp ut
-
)20 0 m A G ro u n de d O u tp u t W h e n
WIRING
4
FEBERARY/06/2006
Advertisement
Table of Contents
