Table of Contents
Advertisement
Eight times
Pink Wire =
Two step door
unlock output
Nine times
Black / Green Wire
Channel 4 Output =
Momentary output
Ten times
Black / Red Wire
Channel 5 Output =
Momentary output
Eleven
Black / Violet Wire
times
Channel 6 Output =
Momentary output
Exit
: Turn Ignition to 'ON' position, or leave it for 15 seconds. A 3 long chirps & 3 parking light flashes to
confirm exit.
Comfort Feature:
Some Vehicles have a special "COMFORT feature". When you lock the door with the key, you just have to
keep on turning the key on the door about 5 or 7 seconds and the window will close directly.
If your vehicle with "COMFORT feature" and you wish the door being locked and the window being closed
automatically at the same time by remote control, you can set the alarm feature
Channel 4 (5 / 6) Timer Control Output Programming.
Momentary output = The momentary output selection will output a negative signal from the Channel 4
(5/6) output immediately when the channel 4 (5/6) button is pressed and will continue until the button is
release.
Latched output = The latched output selection will output a negative signal as soon as the Channel 4 (5/6)
button is pressed and will continue until the button is pressed again.
Latched output / reset with ignition = The latched / reset with ignition output selection operates just like
the latched output but will reset or stop when the ignition is turned on.
Ground Output During Start (Crank) = This wire will provide a 200mA ground output while the starter
output of the remote start unit is active. This output can be used to activate the Crank Low/Bulb Test wire
found in some GM vehicles. This wire is also referred to as the ECM wake up wire in some vehicles.
Start Status Output = This wire will provide a 200mA ground output as soon as the module begins the
remote start process. It can be used with a relay to disconnect a sensor from the system.
Password Pin Code Setup:
1. Turn the Ignition switch 'On then Off 3 TIMES and stay in Off position.
2. Within 10 seconds, push and release the Valet switch 4 times and holding in on the 4
long chirp from siren to confirm you are now in the Alarm feature-programming mode.
3. Within 10 seconds, press and release the Valet switch 7 times again, [7] siren/horn chirp to indicate
your are in features "Password Pin Code Programming mode".
4. Within 10 seconds, begin to enter your chosen 9ths digit by pressing and releasing
9 times.
5. Finish by turning the ignition switch to "On" position.
If the new password code was accepted, the unit would report back the newly entered code, by flashing
the LED, The unit will report the new code three times with a one-second's pause between each code.
Note: If 10 seconds of inactivity expire, the unit will revert back to the last successfully stored code. A [3]
long chirps to confirm exit. Will revert back to the last successfully stored code
Delete Password Pin Code / Override Without Password Pin Code (Factory default setting):
1. Turn the Ignition switch 'On then Off 3 TIMES and stay in Off position.
2. Within 10 seconds, push and release the Valet switch 4 times and holding in on the 4
long chirp from siren to confirm you are now in the Alarm feature-programming mode.
3. Within 10 seconds, press and release the Valet switch 7 times, [7] siren/horn chirp to indicate your are
in features "Password Pin Code Programming mode".
4. Within 10 seconds, press and hold
Password Pin Code.
VS3725IN
Pink Wire = Factory
Security Disarm
Signal Output
Black / Green Wire
Channel 4
Output =
Latched output
Black / Red Wire
Channel 5 Output =
Latched output
Black / Violet Wire
Channel 6 Output =
Latched output
button for 3 seconds. A one long chirps to confirm Deleted the
12
Pink Wire = Start
Status Output
Black / Green Wire
Black / Green Wire
Channel 4
=Ground Output
Output =
During Start (Crank)
Latched output and
reset with ignition
"on"
Black / Red Wire
Black / Red Wire
Channel 5 Output =
Channel 5 Output =
Latched output and
30 seconds timer
reset with ignition
output
"on"
Black / Violet Wire
Black / Red Wire
Channel 6 Output =
Channel 6 Output =
Latched output and
30 seconds timer
reset with ignition
output
"on"
3
"with comfort feature".
FEBERARY/06/2006
th
push until one
button from 1 –
th
push until one
Advertisement
Table of Contents
