Quartz Analog-Digital Chronograph Models - Type A; With Alarm Function; Includes Laptime (Sf 102.4, 102.6, 102.8) Quartz Ana-Digi Models - SCUDERIA FERRARI Pit Crew Operating Instructions Manual

QUARTZ ANALOG-DIGITAL CHRONOGRAPH MODELS – TYPE A
A
H
G
S
B
Figure A
1, 2 – Crown positions
Button A – EL Backlight
Button B – Mode Selection
Button C – Setting Mode
Button D – Start/Stop
H – Analog Hour Hand
M – Analog Minute Hand
S – Analog Seconds Hand
E – Upper Digital display – Mode/Calendar
F – Lower Digital display –Time/Setting
G – Chime ON Indicator
K – Alarm ON Indicator
ß
(
Button B)
Real Time Chronograph
This analog-digital model features analog Hour, Minute and Seconds
hands, and upper/lower LCD digital display with Calendar/Real Time
in 12-hour or 24-hour format, Alarm and Chronograph functions,
and EL backlight.
To select MODE:
Press Button B to cycle through the Modes in this order: REAL TIME à
CHRONOGRAPH à ALARM à TIME SETTING à REAL TIME.
To use EL Backlight: Press Button A at any time to illuminate the
dial for 3 seconds to make reading digital display possible in low light
conditions.

Includes Laptime (SF 102.4, 102.6, 102.8) quartz Ana-Digi models

E
C
M
1 – 2
D
F
Legend
ß ß
( (
Button B) Button B)
Alarm Time Setting

with alarm function

TIME SETTING
To set Digital TIME:
1. Press Button B three times to advance to TIME Setting Mode;
Seconds display will blink.
2. Press Button D to reset Seconds to 00.
3. Use Button C to advance through TIME Setting Sequence in
K
this order: HOUR à MINUTE à MONTH à DATE à DAY OF
WEEK à SECONDS. The active digital field in current Setting
Mode will blink.
4. Press Button D to adjust blinking number.
5. Press Button C to confirm new setting and advance to next field
in setting sequence.
6. Repeat steps 4 and 5 to complete TIME Setting sequence.
7. When finished, press Button B to exit TIME Setting mode.
NOTES: When setting the Time, "H" is displayed for 24-hour
format, and "A" or "P" for 12-hour format.
To select 12- or 24-hour format, press and hold Button C: The
display will cycle through time formats in this sequence: "A" (AM)
time à "P" (PM) time à "H" (24H) time à "A" (AM) time.
If you press D while Seconds display reads 30 to 59, Seconds are reset
to 00 and Time is set to next Minute; if you press D while Seconds
display reads 00 to 29, Minute does not change.
To set Analog TIME:
1. Pull crown out to position 2.
2. Rotate crown in either direction until hands indicate desired time.
3. Press crown back in to position 1, flush against case.
CHRONOGRAPH
In this Mode, watch functions like a stopwatch to measure intervals
of time.
NOTE: You can return to Real Time mode while Chronograph is
running by pressing button B.
To operate CHRONOGRAPH:
From Real Time Mode, press Button B once to enter
CHRONOGRAPH Mode; use Buttons C and D to operate
the Chronograph.
To measure the duration of a single, non-stop event:
1. Press Button D to start timing.
2. Press Button D a second time to stop timing; read elapsed time
in Lower digital display.
3. Press Button C to reset display to zero.
To measure the combined time of a series of shorter events:
1. Press Button D to start timing.
2. Press Button D a second time to stop timing and read elapsed
time in Lower digital display.
3. Press Button D again to resume measurement.
4. Press Button D a fourth time to stop chronograph again,
and read new elapsed time.
NOTE: Each time you stop timing, digital display will indicate total
accumulated time.
5. Repeat steps 3 and 4 to add additional intervals of time,
as needed.