Quartz Analog Chronographs 1/1 Of A Second - Type E - SCUDERIA FERRARI Pit Crew Operating Instructions Manual

QUARTZ ANALOG CHRONOGRAPHS 1/1 OF A SECOND – TYPE E
Includes Formula Italia S (SF 204.1) and RedRev Evo (SF 162.1, 162.2) quartz chronograph models
F
H
E
S
Figure A
1, 2, 3 – Crown positions
Button A – Start/Stop
Button B – Reset
H – Hour Hand
M – Minute Hand
S – Normal Seconds Hand
C – Chronograph Seconds Counter
E – Chronograph Minutes Counter
F – 24-Hour Hand
D – Date Display
These chronograph models feature a minute counter (up to 30),
seconds counter, small 24-hour hand, and date display. They can be
used to time an event up to 29 minutes and 59 seconds in duration
to the nearest second.
Battery end-of-life indicator:
When the battery is almost exhausted, Seconds hand S will start to
move haltingly in two-second intervals, signaling the need to have the
battery replaced as soon as possible. When this happens, the watch
will still keep accurate time, however the stopwatch will not operate.
If battery end-of-life indication begins while a chronograph measure-
ment is being taken, the timing will stop, and the chronograph hands
will reset at their zero position.
To set the TIME and DATE:
NOTE: Before setting the time, make sure chronograph measurement
is stopped and both chronograph hands have been returned to zero
position at 12 o'clock.
1. Pull crown out to position 2.
2. Turn crown counterclockwise until previous day's date appears
in Display D.
NOTE: Do not set date when the time is between 9:00 PM and 1:00 AM,
otherwise the date may not change automatically on the following day.
3. The instant Seconds hand S reaches the 12 o'clock position, pull
crown out to position 3; watch stops.
with small chronograph minutes/seconds counters and 24-hour hand, and date
M
A
D
1 – 2 – 3
B
C
Legend
NOTES: If the crown is pulled out to position 3 while the chronograph
is running, the stopwatch function will stop automatically, and the
hands will reset to zero. When crown is in position 3, it may be turned
clockwise or counterclockwise to move Hour H and Minute M hands
in either direction.
4. Turn crown clockwise advancing Hour H and Minute M hands
past 12:00 midnight to advance Date D to current date; then
continue turning crown clockwise to set Hour H, Minute M and
24-Hour F hands to desired time, taking AM/PM time into account.
NOTES: 24-hour hand F will move in sync with Hour hand H, so
when setting the hour, make sure 24-hour time is set properly.
RECOMMENDATION: When setting Minute hand M, first advance
it 4 to 5 minutes ahead of desired time, then turn it back to the exact
minute.
5. Take an accurate time signal (from a radio news station, for
example). When the audible tone signals the exact time, push
crown back in to position 1; watch will restart, now set to the
exact time.
To RESET Chronograph Hands:
Before setting the time or running the stopwatch, make sure chrono-
graph counter hands C and E are in the zero position at 12 o'clock.
Follow these steps as needed to reset the counter hands following a
battery change or in the event of an error:
1. Pull crown out to position 3.
NOTE: If the chronograph is running or has been stopped while
running, when the crown is pulled out to position 3, the stopwatch
hands will be automatically reset.
2. Press Button A to move stopwatch hands C and E clockwise.
3. Press Button B to move stopwatch hands C and E counterclockwise.
NOTES: To move the hands quickly in desired direction, press and hold
Button A or Button B. Minute hand E is synchronized automatically
with Seconds hand C. To reset hand E, continue to move hand C until
hand E reaches the zero position.
4. Once Chronograph hands C and E have been reset to zero position,
push crown back into position 1.
Operating the CHRONOGRAPH
This stopwatch is able to measure and display time in 1 second
increments up to a maximum of 29 minutes/59 seconds. It will stop
automatically after running continuously for 30 minutes. Measured
time is indicated by Chronograph Minute E and Seconds C hands
which move independently of the center-mounted and 24-hour watch
hands.
Simple chronograph functions:
1. Press button A to start chronograph.
2. Press button A a second time to stop chronograph.
3. Press button B to reset chronograph to zero.
Accumulated time functions:
To measure the combined time of a series of shorter events, for
example the actual playing time of a basketball game, where play is
repeatedly interrupted:
1. Press button A to start chronograph.
2. Press button A a second time to stop chronograph and read
elapsed time.