Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for IC Realtime ICIPD2077P
Summary of Contents for IC Realtime ICIPD2077P
- Page 1 HD Network Mini PT Dome Camera User’s Manual Version 1.1.1...
- Page 2 Welcome Thank you for purchasing our Network camera! This user’s manual is designed to be a reference tool for your system. Please read the following safeguard and warnings carefully before you use this series product! Please keep this user’s manual well for future reference!
-
Page 3: Important Safeguards And Warnings
Important Safeguards and Warnings 1．Electrical safety All installation and operation here should conform to your local electrical safety codes. The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited power source is rated 12V DC or 24V AC in the IEC60950-1. (Refer to general introduction) Please note: Do not connect two power supplying sources to the device at the same time;... - Page 4 Do not touch the CCD (CMOS) optic component. You can use the blower to clean the dust on the lens surface. Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to dilute the mild detergent first and then use it to clean the device.
-
Page 5: Table Of Contents
Table of Contents General Introduction ........................1 Overview ........................1 Features ......................... 1 Specifications ........................ 2 Structure ............................4 Components ........................4 Framework and Dimension ..................4 Device Installation ........................6 Installation Steps ......................6 Restore Factory Default Setup Introduction ............. 8 SD Card Removal and Installation ................ -
Page 6: General Introduction
1 General Introduction 1.1 Overview This series network camera integrates the traditional camera and network video technology. It adopts video data collection, transmission together. It can connect to the network directly without any auxiliary device. This series network camera uses standard H.264 video compression technology, which maximally guarantees the video quality. -
Page 7: Specifications
1.3 Specifications Please refer to the following sheet for network camera performance specification. Model ICIP D2077P Parameter Main Processor High performance DSP Embedded LINUX System Support real-time network monitoring, local record, and remote Resources operation at the same time. User Interface Remote operation interface such as WEB, DSS, PSS System Status SD card status info, bit stream statistics, log, and software version. - Page 8 396 (18*22) detection zones; sensitivity level ranges from 0 to 100; area threshold ranges from 0 to 100. Motion Detect Activation event: video storage, image snapshot, log, email function and etc. Activation event: video storage, image snapshot, log, email function Video Loss and etc.
-
Page 9: Structure
2 Structure 2.1 Components You can refer to the following figure for structure components information. See Figure 2-1 Figure 2-1 Please refer to the following sheets for detailed information. Component Component Name Component 1 Device lens Component 2 Dome enclosure Sheet 2-1 Port Name... - Page 10 Please refer to the following two figures for dimension information. The unit is mm. See Figure 2-2 and Figure 2-3. Figure 2-2 Dimension illustration 1 Figure 2-3 Dimension illustration 2 Note: The figure of quick installation pedestal is not included in this chapter.
-
Page 11: Device Installation
3 Device Installation 3.1 Installation Steps Important Before the installation, please make sure the installation environments can at least support 3x weight of the camera. Figure 3-1 Please follow the steps listed below to install the device. Please refer to Figure 3-1 for reference. Step 1 Please take the installation position map in the accessories bag, and then paste it on the ceiling or the wall according to your monitor area requirements. - Page 12 Figure 3-2 GND threaded hole is set on the device of outdoor vandal-proof dome, please earth the GND port of the device to enhance the device reliability. The GND port is near the cable exit port on the rear of the dome.
-
Page 13: Restore Factory Default Setup Introduction
3.2 Restore Factory Default Setup Introduction Important Please use RESET button when device is running. See Figure 3-4 for the location of RESET button, which is the same for both vandal-proof dome and non vandal-proof dome. Step1 Take down the dome from the installation pedestal. Step2 Open the small cover on the back of the device, for vandal-proof dome (Figure 3-4), you need to dismantle two screws;... - Page 14 removal or installation. Step 1 Take down the dome from the quick installation pedestal. Step 2 Open the small cover on the back and reveal SD card slot. Step 3 SD card slot is flip, so open card cover according to the arrow on the card slot, then you can remove or install SD card.
-
Page 15: Quick Configuration Tool
4 Quick Configuration Tool 4.1 Overview Quick configuration tool can search current IP address, modify IP address. At the same time, you can use it to upgrade the device. Please note the tool only applies to the IP addresses in the same segment. 4.2 Operation Double click the “ConfigTools.exe”... - Page 16 In the configuration tool search interface (Figure 4-1), please select a device IP address and then double click it to open the login interface. Or you can select an IP address and then click the Login button to go to the login interface. See Figure 4-3. In Figure 4-3, you can view device IP address, user name, password and port.
-
Page 17: Web Operation
5 Web Operation This series network camera products support the Web access and management via PC. Web includes several modules: Monitor channel preview, system configuration, alarm and etc. 5.1 Network Connection Please follow the steps listed below for network connection. ... - Page 18 Figure 5- 2 Web login After you successfully logged in, please install WEB plug-in unit. Please refer to the Web Operation Manual included in the resource CD for detailed operation instruction. See Figure 5- 3. Figure 5- 3 Web monitoring window...
-
Page 19: Faq
6 FAQ I can not boot up Please click RESET button for at least five seconds to restore the device or factory default setup. operate properly. The water leakage The unauthorized front or rear cap remove many result in water occurred. -
Page 20: Appendix Toxic Or Hazardous Materials Or Elements
Appendix Toxic or Hazardous Materials or Elements Toxic or Hazardous Materials or Elements Component Name Cr VI PBDE Circuit Board ○ ○ ○ ○ ○ ○ Component ○ ○ ○ ○ ○ ○ Device Case ○ ○ ○ ○ ○ ○...