Document Revision History Date Revision Changes 2010-03-15 V1.0 Release 2013-06-18 V1.1 Modified Product Contents ( Removed Data CD ) (WIZnet Co,. Ltd.) WIZ6000 User’s Manual - 2 -...
Page 3
CE for Class B ITE INFORMATION TO THE USER Hereby, WIZnet. Declares that this WIZ6000 is in compliance with the essential requirements and other relevant provisions of directive 1999/5/EC. WARNING: This is a class B product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
Page 4
Q&A Board. We will reply your questions as soon as possible COPYRIGHT NOTICE Copyright 2013 WIZnet Co., Ltd. All Rights Reserved. Technical Support: support@wiznet.co.kr Sales & Distribution: sales@wiznet.co.kr...
Page 6
Figures 1. WIZ6000 D ......................5 IGURE EVICE ERVER NTERFACE 2. WIZ6000 D ) ......................6 IGURE IMENSIONS UNIT 3. RJ-45 PIN A ..........................7 IGURE SSIGNMENT 4. S ................... 8 IGURE ERIAL ERMINAL ROGRAM CONFIGURATION 5. W ......................9...
Page 7
ONFIGURATION RAME FORMAT 7. S ..................12 ABLE ERIAL ONFIGURATION EPLY RAME FORMAT 8. S STX & ETX ......................12 ABLE ERIAL ONFIGURATION 9. S ......................13 ABLE ERIAL ONFIGURATION EPLY (WIZnet Co,. Ltd.) WIZ6000 User’s Manual - 7 -...
1. Introduction WIZ6000 is the external gate way module which provides a bridge for RS-232 or Ethernet to IEEE802.11 b/g wireless communications. Devices with the interface of RS-232C serial or Ethernet can established a wireless network which can enable remote monitoring, management and controlling.
Figure 1. WIZ6000 Device Server Interface 1.3.1 Hardware Installation STEP1: Connect the WIZ6000 to the HUB or PC by using a network cable. STEP2: Connect the WIZ6000 to the serial device by using the RS-232C serial cable. STEP3: Insert the power supply connector to the WIZ6000 by using the 5V / 2A DC power adaptor.
Hardware Trigger signal Input Receive Data Transmit Data EXT_GND External Power Ground (Internally shorted to GND) Ground Not connect Request To Send Clear To Send EXT_VCC External Power Input (5V) / Optional Table 5. RS-232 PIN Assignment (WIZnet Co., Ltd.) WIZ6000 User’s Manual...
3. Demonstration and Test In this chapter, an example is provided for you to test the functionality of WIZ6000. The testing environments are the followings: <Hardware> A PC equipped with a RS-232 serial port WIZ6000 Device Server Connect PC and module’s Ethernet port by using an Ethernet Cable (Direct or Crossover) Connect PC and module’s serial port by using a serial cable...
③ Connect to “WIZ6000” in the Wireless Network Setting of your PC Figure 5. Wireless Network Connection ④ Execute one more terminal program, and set IP address and Port number. Figure 6. Network Terminal Program configuration ⑤ Input any characters in the Hyper Terminal for Serial. (In the example below, “01234567890”...
Figure 8. Serial to Wireless LAN 구성 ⑥ In the same way, input any character at the screen of terminal program for network, and check if same character is displayed at the screen for serial. ( Ethernet to Serial ) (WIZnet Co., Ltd.) WIZ6000 User’s Manual...
Server IP of the module. If Server mode is not checked, Device Terminal will operate as client mode, and the module as server. For the IP address and port, please input your IP address and port number of WIZ6000 and click the “Connect” button to start a network communication.
Serial Configuration Serial Command Format It is possible to configure WIZ6000 by using serial command. RS-232C port’s Pin number 1 of WIZ6000 is Hardware trigger pin. ( ‘1’: H/W trigger disable, ‘0’: enable ) < Frame Format > Command Frame format...
<x> DHCP Start address_End address Start/End IP <Sxxx.xxx.xxx.xxx_xxx.xxx.xxx.xxx> DHCP Start address_End address Start/End IP <xxx.xxx.xxx.xxx_xxx.xxx.xxx.xxx> Wireless MAC address_Channel_TxRate_RSSI Active Client <Sxxxxxxxxxxxx_xx_xx_xx[:xxxxxxxxxxxx_xx_xx_xx:…]> List <IP address_MAC address> DHCP Client <Sxxx.xxx.xxx.xxx_xxxxxxxxxxxx[:xxx.xxx.xxx.xxx_xxxxxxxxxx List xx:…]> DNS Server 1:Enable, 0:Disable (WIZnet Co., Ltd.) WIZ6000 User’s Manual...
Page 24
[data byte] 7: 7bit, 8bit aBit_Parity_F [parity] 0: no parity, 1: Odd, 2: Even low_Stopbits [Flow] 0: no, 1: Xon/Xoff, 2: RTS/CTS [Stopbits]; 1: 1stop, 2:2stop <xxxxx> 0~65535 Time <Sxxxxx> 0~65535 Time <xxxxx> 0~255 Size <Sxxx> (WIZnet Co., Ltd.) WIZ6000 User’s Manual...
Page 25
There is not in command list <2> Wrong Parameter factor <3> ">" is wrong error code <4> Do not work in current mode No more add list. -Limit- <5> *WDS: 4 list *ACL: 16 list (WIZnet Co., Ltd.) WIZ6000 User’s Manual...
Page 26
If multi command input, response time be delayed For example DA, GA, DW, GW Notice Security Available mode AP/GW Mode AuthMode: 0-7 EncryptType: 0-3 Client Mode AuthMode: 1,3,5,7 EncryptType: 0,1,4 **Security Example parameter <GU5_2_0_0_12345678> <GU4_2_0_0_12345678_abcd_192.168.123.111_1812> (WIZnet Co., Ltd.) WIZ6000 User’s Manual...
WIZnet warrants our products and its parts against defects in materials and workmanship under normal use for period of standard ONE(1) YEAR for the WIZ6000 board and labor warranty after the date of original retail purchase. During this period, WIZnet will repair or replace a defective products or part free of charge.