Cooling Down; Handy Hints - Black & Decker KR540 Original Instructions Manual

ENGLISH
Slide the depth stop until the distance between the
end of the depth stop and the end of the drill bit is
equal to the length of the screw you will fit. Tighten
@ A B B C y z | | @ A B B C CP Q R R S S
   @ A B B C CP Q R R S S
   @ A B B C CP Q R R S S
   CP Q R R S S
   @ A B B C CP Q R R S S
   @ A B B C CP Q R R S S
   CP Q R R S S
   @ A B B C @ A B B C @ A B B C @ A B B C @ A B B C @ A B B C @ A B B C @ A B B C @ A B B C CP Q R R S S
   CP Q R R S S
   @ A B B C CP Q R R S S
   @ A B B C CP Q R R S S
   @ A B B C @ A B B C @ A B B C CP Q R R S S
   @ A B B C @ A B B C @ A B B C CP Q R R S S
   @ A B B C @ A B B C @ A B B C CP Q R R S S
   @ A B B C @ A B B C CP Q R R S S
   CP Q R R S S
   CP Q R R S S
   @ A B B C CP Q R R S S
   CP Q R R S S
   CP Q R R S S
   @ A B B C CP Q R R S S
   CP Q R R S S
   CP Q R R S S
   @ A B B C CP Q R R S S
   CP Q R R S S
   CP Q R R S S
   @ A B B C CP Q R R S S
  
   CP Q R R S S
   @ A B B C CP Q R R S S
   CP Q R R S S
   CP Q R R S S
   @ A B B C CP Q R R S S
   CP Q R R S S
   CP Q R R S S
   @ A B B C CP Q R R S S
   CP Q R R S S
   @ A B B C
the side handle.
PREPARING YOUR DRILL FOR OPERATION
Proceed as follows:
Fit the correct accessory for the job.
setting of the hammer switch, the speed switch or
the forward/reverse when your drill is in operation.
yy yy PP PP @@ @@ PP PP @@ @@ PP PP @@ @@ PP PP @@ @@ PP PP @@ @@ @@ @@ PP PP @@ @@ PP PP PP PP PP PP PP PP PP PP PP PP PP PP @@ @@ @@ @@ PP PP @@ @@ PP PP @@ @@ PP PP PP PP PP PP @@ @@ PP PP PP PP PP PP @@ @@ PP PP PP PP PP PP @@ @@ PP PP PP PP @@ @@ @@ @@ @@ @@ PP PP @@ @@ @@ @@ @@ @@ PP PP @@ @@ PP PP @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ PP PP @@ @@ @@ @@ @@ @@ PP PP @@ @@ @@ @@ @@ @@ PP PP @@ @@ @@ @@ @@ @@ PP PP PP PP @@ @@ PP PP PP PP
USING YOUR DRILL
PP PP PP @@ PP PP PP yy @@ @@ PP PP @@ @@ @@ PP PP PP PP @@ PP PP PP @@ PP PP PP @@ PP PP PP @@ @@ PP @@ @@ @@ PP @@ @@ @@ PP @@ @@ PP PP @@ @@ @@ PP @@ @@ @@ PP @@ @@ @@ PP @@ @@ @@ PP @@ PP PP @@ @@ PP @@ PP @@ PP PP
@@ @@ @@ @@ @@ @@ @@ yy @@ @@ PP PP @@ PP @@ PP @@ @@ @@ PP @@ @@ @@ PP @@ @@ @@ PP @@ @@ @@ PP @@ @@ @@ PP PP @@ PP PP @@ @@ PP PP PP @@ PP PP PP @@ PP PP PP @@ PP PP PP @@ PP PP PP @@ PP PP PP @@ PP PP PP @@ PP PP PP
when operation is continuous, depress the switch
again and release. While your drill is in operation, do
not touch the chuck.

HANDY HINTS

• Fit the correct size and type of drill or screwdriver bit.
• Always hold your drill using the handle and the
side handle.
8
KR540-600 UK p01-12
• Always hold your drill at right-angles to your work.
As a general
hammer switch to the hammer mode
rule, for large
screwdriving, set the hammer switch to the drill
size drill bits use
mode
low speeds and
• Set the forward/reverse switch to the correct direction.
for smaller drill
• Never change the direction of rotation when your
bits use high
drill is in operation.
speeds.
• After use, remove the drill bit and gently tap the side
of the chuck with a soft-faced hammer to remove
the dust. This will extend the life of the chuck.
Set the forward/
reverse switch

COOLING DOWN

to the desired
If your drill becomes too hot in use, allow your drill to
direction of
operate without load for 2 minutes.
rotation. Never
OVERLOAD
change the
Never use excessive force when using your drill. Too
much pressure can reduce the speed of your drill and
reduce its efficiency. This can result in an overload
which can cause damage to the motor of your drill.
To switch your
drill on, depress
EC DECLARATION OF CONFORMITY
the variable
We declare that units: KR540RE, KR540CRE, KR550RE,
speed on/off
KR550CRE, KR600RE, KR600CRE, KR650CRF conform to
switch.
98/37/EC, 89/336/EEC, EN55014, 73/23/EEC, EN55104,
Your drill stops
EN50144
when the switch
A weighted sound pressure 99dB (A)
is released.
A weighted sound power 112dB (A)
If continuous
Hand/arm weighted vibration 8.89m/s
operation is
required,
depress the lock-
on button while
Brian Cooke - Director of Engineering
the variable
Black & Decker Ltd, Spennymoor, County Durham
speed on/off
DL16 6JG United Kingdom
switch is
depressed.
The Black & Decker policy is one of continuous
To stop your drill
improvement to our product and as such we reserve
the right to change the product specification without
prior notice.
8
When drilling
wood and metal,
set the hammer
switch to the drill
mode
When drilling
masonry, set the
.
2
06-02-2001, 10:23
.
. When